tuya KW02 1080P POE IP Doorbell Instruction Manual

tuya KW02 1080P POE IP Doorbell

Function

Outdoor doorbell

• Resolution: 2Mega pixels, 140 Horizontal angle
• Night vision: IR CUT no color deviation, B/W night vision
• Unlock: Power on or off unlock, unlock delay time setting by indoor monitor

7, 10.1 inch capacitive touch 1024*600 indoor monitor

• Connect: Connect up to 2 outdoo doorbells and 6 indoor monitors, the indoor monitors can talk to each other
• Network: Master indoor monitor connects 2.4G WiFi 802.11 b/g/n
• Power adapter: Outdoor doorbell and indoor monitor share a 12V2A power adapter
• Function: Take photo, take video, unlock, lock delay, motion detection calendar, adjust brightness, contrast, color
• TF Card: External TF card to save photos or videos, leave messages

TuyaAPP

20 App users can connect to the system, users can talk to visitors anytime and anywhere, and take photo or video, monitor, unlock

• Message: Push photo to APP when motion detection or call
• Playback: Video recording after the call or motion detection
• Third-Party: Amazon echo, Google Home, Cloud storage

Outdoor camera

Packing list

Installation diagram

The outdoor doorbell is installed at a height of 1.4~ 1.7 meters, try to avoid the sunshine and rain, Using 2 screws or tape fixed the outdoor doorbell on the wall, wooden board, door, It can also be installed on the 86 box.

1. Use the drill bit to drill three holes. One hole is large enough to pass through the 4pin cable, use anchors if user install outdoor doorbell on brick or concrete.
2. Remove the screws from the rain cover
3. The rain cover is separated from the doorbell
4. The 4pin cable goes through the hole in the wall
5. Fix the rain cover with two screws
6. Plug the rain cover on the doorbell and fix the bottom screws
7. Fix the hanging plate to the wall with two screws
8. Insert the MicroSD card to the slot of indoor monitor
9. Connect the other end of the 4pin cable to Doorl or Door2 of the indoor monitor
10. Connect the indoor monitor to a 12V 2A power adapter
11. Hang the indoor monitor to the hanging plate

Schematic diagram of connect the lock

Note: Unlock voltage is 12V. Pis check the ower supply specification to purchase separately. Please set the unlock delay time in the master indoor monitor.

Connect outdoor doorbell and indoor monitor

Dool, Door2:
Connect the 4pin cable, the other end of the 4pin cable connects to the doorbell.

In: Connectthe4pin cable, the other end ofthe4pin cablemnnectstothe “Out” of the last indoor monitor Out: Connectthe4pin cable, the other end ofthe4pin cable mnnects to the “In” of the next slave

1. The 4pin port of the outdoor doorbell same as that of the indoor monitor. The other end ofthe4pin cable is connected to “Doorl” of the indoor monitor. If there are two outdoor doorbell, the other outdoor doorbell is connected to “Door2”
2. Connect up to 2 outdoor doorbells and 6 indoor monitors.
   Note: Enter “Settings”-> “System Settings” of the indoor monitor, the device ID of the master indoor monitor connected to the outdoor doorbell is 1. The slave indoor monitors are sequentially set to 2, 3, 4, 5, 6.

Indoor monitor operation introduction

1. Settings
   System setting:

   • Device ID: Master indoor monitor setting connected to outdoor doorbell, Master indoor monitor ID setting to 1. ID of Slaves are setting sequentially 2,3,4, 5, 6
   • Standby clock switch: on/off
   • Language: English, Russian, French, Spanish, German and Simplified Chinese
   • Key tone: on/off
   • Ring back: on/off
   • Advanced settings: Format SD disk, Factory Settings, Software upgrade, restart system.
   • Information: Software version, Release date, SD remain space, UUID

2. Click “Monitoring” button or after visitor presses the “call” button of the outdoor doorbell.

   • Monitor next doorbell
   • Adjust the brightness, saturation
   • Zoom out
   • Talking: User is talking with the visitor

3. After clicking “Inter call”, user can call another indoor monitor.

4. Click “recording” to display the record of the call, message, and Motion. Short press the file to play video or browse the photo, long press to ‘delete’, “All delete”, “All read”

5. Working modes
   Note: The indoor monitor needs to insert the TF card and the message is enabled.

6. Door settings
   Note: Below setting by the main indoor monitor, the slave synchronizes the settings.

   • Enable switch: Please check whether the outdoor doorbell is connected. If only one outdoor doorbell is connected, please turn off the enable of the unconnected outdoor doorbell.
   • Unlock delay: Set the time of close lock.
   • Record mode: Take video or photo when visitor calls or motion detection is triggered.
   • Motion detect switch: Motion detection enabled or disabled.
   • Motion detect sensitivity: low/medium/high
   • Motion detection duration: After triggering motion detection, setthe recording time
   • Message switch: Turn on/off the leave a message.
   • Message time: Set the leave a message time.
   • Signal mode: PAL/NTSC/Automatic
   • Signal type: The outdoor doorbell is AHD1080, if user connect to other analog outdoor doorbells, please select the signal format, Select automatic detection, so that the door phone can be used normally. Support AHD1080/AHD720/1Vl720/TVl1080/CVl720/CVl1080/CVBS.
   • Ring setting: Can setting by slave indoor monitor Setthe ringtones for 3 time periods, the ringing time of the ringtone, choose one of 10 ringtones, Ringer volume 0~ 10

App Download

1. Search “Tuya Smart” or “Smart life” from APP store or Google Play according to phone system.
2. Scan the QR code below to download

APP register & login

1. Please register when using APP for the first time.
2. After logging on the APP, please add devices after creating a family. At the bottom right corner of the APP homepage, click “Me”-> “Home Management”-> “Create a home”, fill in the information and save it. The user who adds the device will become family-owned and can set the family owner or general members.
3. After the homeowner adds the device, the home members will add the device automatically. After adding this doorbell, all home members have an unlocked function than shared accounts. Users can add 20 administrators or home members.
4. The video doorbell is a device with a higher security level, the device must be removed from the original account before it can be bound to another account.

Add Master indoor monitor to APP

Note: only the master can connect to the Tuya Smart APP, the slave cannot be connected. Click “Settings” to enter “Network Settings” to enter the network setting.

Indoor monitor has two network pairing modes 1. EZ Mode 2. AP Mode

1. Click”+” on the top right of the homepage.

2. Select “Add Manually”->”Security & Video Surveillane” -> “Smart Doorbell”.

3. Select item 3 “EZ mode”

4. Confirm that the indoor monitor is in the network configuration mode, check it, and click “Next”.
   The indoor monitor only connect 2.4G WiFi, cannot connect 5G WiFi signal!

5. Select the 2.4GHz WiFi to be connected, enter the WiFi password then click “Next”.

6. Enter the “Adding device … ” then “Scan devices.” -> “Register on Cloud.”-> Initialize the device.”, Wait for about 1 minute.

7. It shows that the added successfully, user can modify the device name, and click “Done” to finish the adding the device.

AP Mode A
Select “AP Mode” then click the “return” W icon, the indoor monitor will restart system, and then return to the network setting interface, will display hotspot Smartlife-XXXXXX, the password is 12345678.

1. Click”+” on the top right of the homepage.

2. Select “Add Manually”->”Security & Video Surveillane” -> “Smart Doorbell”.

3. Select the second item “AP Mode”

4. Check this check box and click “Next”.

5. Select 2.4GHz WiFi, enter the WiFi password, and click “Next”.

6. Click the “Go to Connect” icon.

7. Connect to the Smartlife-XXXXXX hotspot, enter the password “12345678”,
   Click the “Back” icon in the upper left comer to return to the APP.

8. Enter the “Adding device  ” then “Scan devices.”> “Register on Cloud”Initialize the device”. This process takes about 1 minute.

9. It shows that the added successfully, user can modify the device name, and click “Done” to finish the adding the device.

Help and service

Users can click “Me” of hompage on the APP to enter “service and help”.

1. “Voice third-party service”, user can choose multiple smart product voice control products, each third party, the third-party service have detailed connection tutorials.
2. “Home Management” can create a home or join a home and set permissions
3. “Message Center” can view alarm information
4. If user are not familiar with the app or device, pis check “Help and Feedback”.

Live video

Click on the device on the homepage of APP to enter the living screen, user can take photos, talk, video, unlock, playback(stored in the MicroSD Card), and view albums.

1. Modify icon, name, and location of the device.
2. View IP address, ID, time zone.
3. Configure the device automation.
4. Connect Amazon Echo or Google Home.
5. 1 Turn on/off the light of the doorbell button 2 The screen horizontal mirroring.
6. Adjust the volume of the doorbell
7. Motion detection on/off, set the alarm sensitivity and the alarm time period.
8. Check the capacity of the memory card, and format the memory card.
9. The device will push the alarm information list to the APP after30 minutes
10. Please check the common problems carefully.
11. Enter the mobile phone number or email address of the user you wantto share, click “Finish”, the shared user cannot unlock.
12. After removing the device, the device will not be displayed on the device list

Motion detection and call push

1. After the visitor presses the call button, push notifications on line
2. The mobile phone standby state is pushed notifications as follows

FCC WARNING

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC’s RF Exposure guide lines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>