Braber Equipment 35.410.005 Hydraulic Floor Jack Instruction Manual
- June 3, 2024
- Braber Equipment
Table of Contents
35.410.005 Hydraulic Floor Jack
Instruction Manual
35.410.005 Hydraulic Floor Jack
MODEL NO.| MODEL NO.| BASE SIZE| MIN. HEIGHT| MAX.
HEIGHT| TOTAL LIFT
---|---|---|---|---|---
35.410.005| 35.410.005| 59.2”x14.4”| 6.3”| 23.6”| 17.3”
35.410.010| 35.410.010| 59.2”x14.4”| 6.3”| 23.6”| 17.3”
SAFETY & WARNING INFORMATION
This is the safety notification symbol. This symbol will notify you of any
potential injury hazards. Please follow all instructions that follow this
symbol to avoid possible injuries and death.
WARNING Indicates a hazardous situation. If proper steps are not
followed, death or serious injury could result.
IMPORTANT: READ ALL INSTRUCTIONS BEFORE USE
Before operating this device, be sure to read all content within this manual,
ensuring that you understand the operating procedures, maintenance
requirements and all safety warnings. The owner and/or operator shall have an
understanding of the product, its operating characteristics, and safety
operating instructions before operating this device. Safety information shall
be emphasized and understood. If the operator is not fluent in English, the
product and safety instructions shall be read to and discussed with the
operator in the operator’s native language by the purchaser/owner or his
designee, making sure that the operator comprehends their contents.
WARNING: ACTIONS TO HELP PREVENT DANGEROUS SITUATIONS
- Study, understand and follow all instructions before operating this device.
- Do not exceed the rated capacity stated.
- Use only on hard-level surfaces.
- Support the vehicle with appropriate means immediately after lifting.
- Do not move or dolly the vehicle while it is on the jack.
- Lift only on areas of the vehicle as specified by the vehicle manufacturer.
- No alterations shall be made to this product.
- Failure to heed these markings may result in serious personal injury/property damage.
SETUP OPERATION & PREVENTIVE MAINTENANCE
SETUP
- Prior to each use, a visual inspection (See Pg. 5) shall be made to the device by checking for abnormal conditions, such as cracked welds, leaks, and damaged, loose, or missing parts.
- Consult the vehicle owner’s manual to determine the location of lift points.
- Be sure to set the vehicle in park with the emergency brake on and wheels securely choked.
- Be sure that the vehicle and the jack are on a hard, level surface.
ASSEMBLY
- Insert the bottom end of the T-handle into the handle fork and locking hole and securely tighten the bolt.
- Slightly turn the release valve while inserting to ensure the proper seating in the U-joint.
**LIFTING**
- Turn the release valve knob located on top of the T-handle clockwise to the closed position.
- Position the jack under the specified lift point.
- Press the foot pedal down to quickly lift the saddle to the contact point.
- Begin lifting by pumping the T-handle up and down.
- Immediately after lifting, support the vehicle with appropriately rated jack stands
- Turn the release valve located on top of the T-handle slowly counterclockwise to lower the vehicle onto the ground.
LOWERING
- Turn the release valve knob located on top of the T-handle clockwise to the closed position.
- Position the jack under the specified lift point.
- Press the foot pedal down to quickly lift the saddle to the contact point.
- Begin lifting by pumping the T-handle up and down.
- Remove the jack stands. Do not get under or let anyone get under the vehicle while lowering.
- Turn the release valve located on top of the T-handle slowly counterclockwise to lower the vehicle onto the ground.
MAINTENANCE
NOTICE:
- Use high-grade hydraulic oil only. Neveruse brake fluid, motor oil, transmission fluid, turbine oil or any other fluids. ISO-VG22 or equivalent hydraulic oil is recommended.
CHECK AND REFILL THE OIL
- With the jack in the fully lowered, level position, remove the unit cover, then remove the oil filler plug.
- The proper oil level should be just covering the inner cylinder as seen from the oil filler plug hole.
- Do not overfill. Always fill with new, clean hydraulic jack oil as recommended above.
- Reinstall oil filler plug, then reinstall the unit cover.
LUBRICATION AND CLEANING: Periodically clean and lubricate all moving
parts and pivot points.
AIR VENTING PROCEDURES
- With the jack in the fully lowered position, release the valve open, and remove oil filler plug.
- Pump the handle rapidly several times. Reinstall the oil filler plug.
- Turn the handle/release valve clockwise to the closed position.
- Pump the handle until the lift arm reaches maximum height and continue to pump several times to remove trapped air in the system.
- Turn the handle/release valve counterclockwise in one full turn and lower lift arm to the lowest position. Use the force on the saddle if necessary.
- Carefully and slowly loosen the oil filler plug to release pressurized air.
- Repeat the above steps until the trapped air is completely vented.
DAMAGED EQUIPMENT
Any jack that appears to be damaged in any way, is found to be worn or
operates abnormally SHALL BE
REMOVED FROM SERVICE UNTIL REPAIRED: It is recommended that necessary
repairs be made by a manufacturer’s or supplier’s authorized repair facility
if repairs are ermitted by the manufacturer or supplier
ALTERATIONS
Because of potential hazards associated with this type of equipment, no
alterations shall be made to the product.
ATTACHMENTS AND ADAPTERS: Only attachments and/or adapters supplied by
the manufacturer shall be used.
INSPECTION, STORAGE & TROUBLESHOOTING
INSPECTION
- Visual inspection shall be made before each use of the device by checking for abnormal conditions, such as cracked welds, leaks, and damaged, loose, or missing parts.
- Other inspections shall be made per product operating instructions.
- This device shall be inspected immediately if the device is believed to have been subjected to an abnormal load or shock. It is recommended that this inspection be made by a manufacturer’s or supplier’s authorized repair facility.
- Owners and/or operators should be aware that repair of this equipment may require specialized knowledge and facilities. It is recommended that an annual inspection of the product is made by a manufacturer’s or supplier’s authorized repair facility and that any defective parts, decals, or safety labels or signs be replaced with the manufacturer’s or supplier’s specified parts.
STORAGE
This Jack should be stored in a dry location on a level surf
TROUBLESHOOTING
SYMPTOM | POSSIBLE CAUSES | SOLUTION |
---|---|---|
Jack will not lift the load. | 1. Release valve is not tightly closed. |
2. Low oil level.
3. Defective or worn internal parts.
4. Load exceeds the maximum allowance.| 1. Tighten the release valve.
2. Check and add oil. Follow “Check
and Refill Oil” instructions on Pg.4.
3. Discontinue use and contact a local repair center.
4. Use a higher-capacity jack.
Jack will not hold the load.| 1. Release valve not tightly closed.
2. Power unit malfunction.| 1. Tighten the release valve.
2. Discontinue use and contact a local repair center.
Jack will not descend to a minimum height, or will ot remain in the lowered
position.| 1. Air trapped in the system.
2. Reservoir oil overfilled.| 1. Vent air out of the system. Follow “Air
Venting Procedures” on Pg. 4.
2. Check and ensure proper oil level. Follow the “Check nd Refill Oil”
instructions on Pg.4.
Jack will not lift to max height.| 1. Low oil level.| 1. Check and ensure
proper oil level. Follow the “Check and efill Oil” instructions on Pg.4.
Jack will not function properly after trying the olution.| 1. Internal
malfunction or structural damage.| 1. Stop usage and contact an authorized
repair center.
REPLACEABLE PART LIST
PART NUMBER
REF | 35.410.005 | 35.410.010 | Front Wheel Assembly | 2 |
---|---|---|---|---|
1 | Saddle | 1 | ||
2 | Return Spring | 1 | ||
3 | 105.103B.003 | 105.104B.003 | Fork Return Spring | 1 |
4 | Power Unit Assembly | 1 | ||
5 | Handle Assembly | 1 | ||
6 | Rear Caster Assembly | 2 | ||
7 | 105.103B.002 | 105.104B.002 | Cover Plate | 1 |
* Items not identified by part number are not available for replacement.
WARRANTY INFORMATION
TWO YEARS LIMITED WARRANTY
For a period of two (2) years from your purchase date, BE AG & INDUSTRIAL
will repair or replace (at its option) without charge, your BE AG & INDUSTRIAL
product if it was purchased new and the product has failed due to a defect in
material or workmanship which you experienced during normal use of the
product. This limited warranty is your exclusive remedy.
If this BE AG & INDUSTRIAL product is altered, abused, misused, modified, or
undergoes service by an unauthorized technician, your warranty will be void.
We are not responsible for damage to ornamental designs you place on this BE
AG & INDUSTRIAL product and such ornamentation should not cover any warnings
or instructions or they may void the warranty. This warranty does not cover
scratches, superficial dents, and other abrasions to the paint finish that
occur under normal use.
To access the benefits of this warranty, contact the dealer or retailer where
the unit was purchased. For further assistance, you can contact BE AG &
INDUSTRIAL at warranty@brabereq.com for
confirmation that this warranty applies. Thereafter, you may be advised to
return the product under warranty, freight prepaid, to the dealer or directly
to the BE AG & INDUSTRIAL service department .
Subject to the law in your state:
- Your sole and exclusive remedy is the repair or replacement of the defective product as described above.
- BE AG & INDUSTRIAL is not liable for any incidental damages, including but not limited to, lost profits and unforeseeable consequences.
- The repair and replacement of this product under the express limited warranty described above is your exclusive remedy and is provided in lieu of all other warranties, express or implied. All other warranties, including implied warranties and warranties of merchantability or fitness for a particular purpose, are disclaimed and, if the disclaimer is prohibited, these warranties are limited to two years from your date of purchase of this product.
PARTS@BRABEREQ.COM
TOLL FREE PHONE
FRAIS: 1-877-588-3311
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>