SYNCHRO 152Y Remote Controller with Control Box User Manual
- June 5, 2024
- SYNCHRO
Table of Contents
Remote controller: 152Y Control box (works with remote controller) :152Y
152Y–USER’S MANUAL
I.ELECTRONICS OVERVIEW
Remote controller: 152Y Control box (works with remote controller) :152Y
II. PAIRING THE WIRELESS REMOTE
STEP 1
Push in on bottom of remote to release battery cartridge and install three AAA
batteries into the remote battery compartment.Push in firmly to close.
STEP 2
- Plug the base into a power source and press the Pairing Button/Program Button on the control box approximately in 1s, ensure the Pairing Lamp – White (Third) flashing.
- Pairing Button/Program Button
- Pairing Lamp – White (Third)
STEP 3
- Press “SW” until the backlight LED flashing ,release it and then press “HEAD UP” ,never release until the backlight LED is lighting all long,the remote is pairing and release it.
- Second, Press “BACK UP”, never release until the backlight LED is lighting all long and then release.
- First, Press “SW” button until the backlight LED flashing and then release.
- When the Pairing Button/Program Button on the control box and the backlight LED on the remote stop flashing, and the buzzer on the control box has a “DI” sound, pairing is completed.
- If the function on the remote can not be operated, repeat the pairing again.
III. FUNCTIONAL OPERATING FOR WIRELESS REMOTE
| MARK | STEP1 | STEP2 | FUNCTIONAL | DESCRIPTIONS |
|---|
| Press “SW” in 3s until the
backlight LED flashing and then press the “BUTTON” in STEP 2| TV| MEMORY
POSITON|
The backlight LEDs all OFF before operating.
• Press（TV,ZG,M）until the backlight LED is lighting andl the memory position
is completed.
• When the backlight LED is lighting and press again, clearl the corresponding
memory position.
• TVl & ZG have the memory position, M no memory position.
ZG
M
BACK UP| PAIRING| Pairing the remote and control box.
Press LEG UP 3 seconds| CONTROL SWITCHING| Control Switching is the backlight
LED of “SW” is OFF.
Press SW 3 seconds| Control Switching is the backlight LED of “SW” is ON.
Press BOTTOM LED 3 seconds| Control Switching is the backlight LED of “SW” is
FLASHING.
IV. FUNCTIONAL OPERATING FOR WIRELESS REMOTE
Power supply:
Input: 100-240V ~,50/60Hz
Output: 29.0V 1.8A
Motor: By pairing the remote control with the control box, the motor can be controlled up and down
Product interface description
The interfaces in the red box below are only used for engineering testing and are not open to consumers.
FCC/ISEDC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment .
This transmitter must not be colocated or operating in conjunction with any
other antenna or transmitter
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>