cannice H876-08 Wireless Over-Ear Headphones User Guide

: June 5, 2024
: cannice

cannice H876-08 Wireless Over-Ear Headphones User Guide

Start here

Following items are included

cannice H876-08 Wireless Over-Ear Headphones User Guide - Following items
are included

Product overview

cannice H876-08 Wireless Over-Ear Headphones User Guide - Product
overview

Status indicator

cannice H876-08 Wireless Over-Ear Headphones User Guide - Status
indicator

Pairing

Pair one phone

Note: When the earphone and phone have been paired once, they will automatically connect when the earphone is on and Bluetooth is activated on the phone.

Make sure the earphone is turned off and within 1 meter of your phone, press and hold the Multifunction button until the LED indicator flashes red and white alternately (About 5 seconds), then release Multifunction button.
Activate Bluetooth on your phone (See below for more details).

iPhone

a. On your phone, open the Settings menu.
b. Select Bluetooth . If Bluetooth is off, turn it on. The iPhone will search for new devices automatically.

Android phone

a. On your phone, open the Settings menu.
b. Select Bluetooth (For old Android phone, Bluetooth is found in the Wireless & Networks ). If Bluetooth is off, turn it on. Select Search for Devices if your phone does not automatically search for new devices.

Pair another phone

Multipoint technology enables you to pair another phone and take a call from either.

To pair with another mobile phone, follow the steps for “Pair one phone”. After pairing successfully, restart the earphone to connect to 2 paired mo bile phone automatically.

Calling switch When the first phone call rings, press the Multifunction button once to answer the call, if the seconds call rings at this moment, you can answer the second phone by double click Multifunction button, and on hold the first phone call.

cannice H876-08 Wireless Over-Ear Headphones User Guide - Pair another
phone

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: ( 1 ) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Call

Answer a call
Press the Multifunction button once.
Reject a call
Press and hold the Multifunction button for about 2 seconds.
End a call
Press the Multifunction button once.
End current call and answer new call
When a new call rings during a call, press the Multifunction button once to answer new call and end current call simultaneously.
On hold current call and answer new call
When a new call rings during a call, double the Multifunction button to hold current call and answer new call.
Reject the new call hold the current call
If new call comes in during active call, long press the Multifunction button for 2 seconds to reject the new call and keep the active call

Switch between the earphone and phone
Press the multifunction button for about 2 seconds during a call, the call will be switched to the mobile phone, redo this operation again, the call will be switched to the earphone.

Siri open(Need phone support)
In standby mode double the Multifunction button, wait for phone prompt and then tell the phone to dial the name of a stored contact.

Music

(Need media player support).

Music play / pause
Press Multifunction button once to play / pause music. (Some phones may require you to start a media player first) .

Track back/ forward
Press the Volume “+” for 2 seconds once to skip track backward, press Volume “-” for 2 seconds once to skip track forward.

Basic operation

Charging

Your new earphone has enough power to pair and make a few calls. It takes 2 hours to fully charge the earphone; while charging, the battery indicator light is red, the indicator light stays white charging is complete.

Note: The lifetime of the battery will be significantly reduced if your earphone is left uncharged for a long period. We recommend that you recharge your earphone at least once a month.

cannice H876-08 Wireless Over-Ear Headphones User Guide -
Charging

Clear paired list

Press volume “+” and volume “-” button at the same time 3s,The red light flashes three times a second

ANC

Power Off state ANC On: When the headphone is turned off, The headset is IN ANC passthrough state. Press ANC button to enter ANC ON

ANC Off: When the headset is OFF, after Passthrough/ANC ON mode is ON, press the ANC button for 2 seconds in any state to enter ANC OFF

Power On state ANC Passthrough: When the headset is off, long press the ANC button to enter ANC Passthrough mode, and short press the ANC button to enter ANC ON, so as to loop switch between the two modes

ANC On: The headset is IN ANC passthrough state. Press ANC button to enter ANC ON

ANC Off: When the headset is OFF, after Passthrough/ANC ON mode is ON, press the ANC button for 2 seconds in any state to enter ANC OFF

Safety and care

Using earphone at high to moderate volumes for extended periods of time will result in permanent hearing damage .It is advised you keep volume levels moderate to low at all times for your safety.

Do not use while driving a car, cycling, operating machinery, or performing other activities that require hearing surrounding sounds.

Do not use earphone in thunderstorm weather, the earphone may not work properly in the condition, and increase the risk of being hit by lightning .

Earphone may not work properly under high temperature or high humidity conditions.

Do not use any corrosive cleaner/oil to clean the earphone. If the earphone comes in contact with liquids, quickly wipe away .If submersed in water, do not turn the earphone on until completely dried.
Tips: liquid submersion voids the warranty.

Keep the earphone and packaging out of reach of children .

Battery protection statement

Do not immerse the battery in water or allow it to get wet.
Do not use or store the battery near sources of heat such as a fire or heater.
Don’t use any chargers other than those recommended.
Do not put the battery into a fire or apply direct heat to it.
Do not place the battery in a microwave oven or pressurized container.
Don’t use the battery if it gives off an odor, generates heat, becomes discoloured or deformed, or appears abnormal in any way. If the battery is in use or being recharged, remove it from the device or charger immediately and discontinue use.

Operating environment: