dyson N358J Purifier Humidify+Cool User Manual
- June 5, 2024
- dyson
Table of Contents
- Getting started
- Assembling your machine
- Filling the water tank
- Power and continuous monitoring
- Information menu
- Auto purify mode
- Auto humidify mode
- Oscillation
- Airflow speed and direction
- Sleep timer
- Night mode
- Deep cleaning your machine
- Changing your HEPA+Carbon filter
- Looking after your machine
- Alerts
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
dyson N358J Purifier Humidify+ Cool autoreact
User manual
SV12 JN.
00000 PN.000000-00-0000.00.00
VERSION NO.01
Dyson purifier humidify plus cool
auto react
Getting started
The layout of the remote control with the standby button on the top left, the Auto purify mode button below, then the Airflow speed toggle up and down button. Below that is the Oscillation button and finally at the bottom is the Sleep timer button. On the top right-hand side is the Information menu button, then going downwards, the Auto humidify mode button, humidity control toggle button, Airflow direction and then Night mode button at the bottom.
Assembling your machine
Use both hands to lift your machine out of the box, by its base. Do not lift
out by the loop amplifier.
Assemble your machine with the filters that are supplied.
Your machine comes with a permanent catalytic filter and a HEPA+Carbon filter.
Push the HEPA+Carbon filter into the outer cover and position on the base.
Push firmly until both outer covers click into place.
Place the remote control on top of the machine with the buttons facing down.
Plug in and switch on.
The purifying humidifying fan with the filter covers open showing a HEPA plus
carbon filter located in the filter covers and a catalytic filter. Arrows
demonstrate that the catalytic filter is fitted directly to the base of the
machine and the filter covers will need to be assembled onto the base of the
machine.
Filling the water tank
Before you remove the water tank, make sure humidification modes are turned
off and the water tank is empty.
Keep the cap dry
Keep the cap on the water tank dry when you run a Deep clean cycle or fill the
tank. It contains power connections and should not be washed. If wet, wipe
thoroughly with a dry cloth. Make sure the cap and connections are completely
dry before refitting.
Remove the tank
Push down the Water tank release buttons on the sides of your machine.
Slide the water tank out of your machine.
Carry the water tank by its handle to the tap, and unclip the cap.
Fill the tank
Fill the water tank to the Max level with cold tap water.
Replace the tank
Replace the cap and secure the cap clips in place.
Make sure the cap is completely dry. If wet, wipe thoroughly with a dry cloth.
Slide the water tank back into your machine until it clicks securely in place.
Power and continuous monitoring
Stand-by on/off
Press the Standby on/off button on your Dyson purifier humidifier fan or
remote control to stop your machine. It will continue to monitor the air
quality.
Continuous monitoring
Continuous monitoring is turned off by default. Once turned on, it will always
be active until you turn it off again.
With continuous monitoring turned on, your Dyson purifier humidifier fan will
gather air quality, temperature and humidity information, which is displayed
on the LCD screen.
Continuous monitoring on/off
Press and hold the Auto mode button on the remote control for 5 seconds to
turn it on. The LCD screen will indicate when continuous monitoring is on or
off.
Information menu
Press this button to scroll through the information being monitored by your
Dyson purifying humidifying fan.
Information about air quality, temperature, humidity. Filter and evaporator
levels are shown.
When a particular type of pollutant causes air quality to decrease, an icon
for the pollutant will show on the LCD screen.
The remote control with the information button on the top right.
Indoor air quality – 12 seconds
Monitor the current air quality with a graph showing the last 12 seconds of
data.|
---|---
Particulate matter (PM10)
Larger microscopic particles up to 10 microns in size, are suspended in the
air we breathe. These include dust, mold, and pollen.
Nitrogen dioxide and other oxidizing gases
These potentially harmful gases are released into the air by combustion, for
example, the burning gas when cooking and in vehicle exhaust emissions.
Indoor humidity
The amount of water vapor in the air, is shown as a percentage.
Particulate matter (PM2.5)
Microscopic particles up to 2.5 microns in size, are suspended in the air we
breathe. These include smoke, bacteria and allergens.
Volatile organic compounds
VOCs are typically odours that may be potentially harmful. These can be found
in cleaning products,
paints and furnishings.|
---|---
Monitor the ambient temperature to help maintain
a comfortable environment. Indoor temperature
Indoor air quality – 24hrs
Monitor the current air quality with a graph showing the last 24 hours of
data.
Filters
The remaining filter life is shown on the LCD screen and will indicate when
your filters need replacing.
Evaporator
The status will show how full the evaporator is with limescale and how soon a
deep clean cycle is required.
Auto purify mode
Set your Dyson purifying humidifying fan to Auto purify mode and the onboard
sensors will intelligently adjust the settings of your machine according to
the air quality.
Air quality: your machine will pause when the target air quality has been
reached, switching on again when the air quality levels drop. Airflow speed:
the airflow speed will increase until the target air quality and temperature
have been reached. Night mode: your machine will only run with airflow speeds
from 1 to 4.
The remote control with the Auto purify button on the left hand side, below the Standby button.
Auto humidify mode
Set your Dyson purifying humidifying fan to Auto humidify mode and the onboard
sensors will intelligently adjust the settings of the machine according to the
temperature and humidity of your room.
Room humidity: your machine will pause when the target room humidity has been
reached, switching on again when the room humidity levels drop.
Airflow speed: the airflow speed will increase until the target humidity level
has been reached.
To turn off Auto humidify mode or to change the humidity levels manually,
press the Humidity control button.
The remote control with the Auto humidity button on the right-hand side, below
the information button.
Oscillation
Press the Oscillation button and select the angle of oscillation to 0°, 45°,
90° or Breeze mode.
Pause the oscillation at any point by pressing the Oscillation button.
Press the Oscillation button again to resume.
To reset the Oscillation direction to the centre, press and hold the
Oscillation button for two seconds.
The remote control with the oscillation button on the left above the sleep timer.
Airflow speed and direction
Press the Airflow speed button to increase and decrease the airflow speed.
Press the Airflow direction button to change the direction of airflow from
front to back.
Change the airflow direction for your personal comfort.
Select the Airflow direction to Fan mode for airflow from the front for
purifying and cooling.
Set the Airflow direction to Diffused mode, for airflow from the bock for
purifying without cool air.
Your machine will continue to purify and humidify (if selected) in both Fan
and Diffused modes.
The remote control with the Airflow speed toggle button on the left-hand side, below the Auto, purify button. The Airflow direction button is on the right above the Night mode button.
Sleep timer
Your Dyson purifying humidifying fan will turn off automatically after the
selected amount of time.
To set the time: press the button to scroll through the time options.
Once activated, press the Sleep timer button once to see the time selected.
To cancel the Sleep timer: press the Sleep timer button to scroll through all
the options and select the cancel option.
The remote control with the sleep timer button on the bottom left.
Night mode
In Night mode, your Dyson purifying humidifying fan will continue to monitor
and respond to changes in air quality and temperature, but only using its
quietest settings – and with its LCD screen dimmed.
If Auto purify mode or Auto humidify mode hove been set, Night mode will
reduce the airflow speed to a range from 1 to 4.
The remote control with the Night mode button on the right at the bottom.
Deep cleaning your machine
To always get the best performance from your Dyson purifying humidifying fan,
it is important to carry out regular deep cleaning to remove any limescale.
Before and after long periods where humidification is not used, we recommend
you run an additional Deep clean cycle.
In hard water areas you may need to run the Deep clean cycle more frequently.
We recommend you use filtered water to always get the best performance from
your machine.
Your machine will alert you when it needs you to carry out a Deep clean cycle.
The LCD screen on your machine will alert you and the Deep clean cycle button
will light up.
To cancel the Deep clean cycle at any point, press and hold the Deep clean
cycle button for five seconds.
Keep the cap dry
Keep the cap on the water tank dry when you run a Deep clean cycle or fill the
tank. It contains power connections and should not be washed. If wet, wipe
thoroughly with a dry cloth. Make sure the cap and connections are completely
dry before refitting.
Step 1
Remove the water tank
Press the Deep clean cycle button on the front of your machine and your
instructions will be shown on the LCD screen.
Push down on the Outer cover release buttons to remove the outer covers.
The inner door will spring open. Put the Outer covers to one side as you carry
out the Deep clean cycle.
Push down the Water tank release buttons on the sides of your machine.
Slide the water tank out of your machine and unclip the cap.
Step 2
Remove the evaporator
Remove the evaporator from your machine, place it in the water tank and refit
the cap.
Step 3
Make a descaling solution
Carry the water tank by its handle to the tap.
Remove the cap and evaporator. Fill the water tank halfway to the Max level
with cold tap water.
Measure out 150g of citric acid and place it in the water tank.
Agitate gently until all the citric acid has dissolved.
Place the evaporator in the water tank. Fill the water tank to the Max level
with cold tap water.
Step 4
Replace the cap
Replace the cap and secure the cap clips in place.
Wipe off any excess water to avoid drips.
Make sure the cap is completely dry. If wet, wipe thoroughly with a dry cloth.
Step 5
Replace the tank
Slide the water tank back into your machine until it clicks securely in place.
When prompted by the LCD screen, press the Deep clean cycle button.
The Deep clean cycle will start and the LCD screen will show a countdown
timer.
Step 6
Remove the water tank
When the LCD screen shows the Deep clean cycle is complete, push down the
water tank release buttons on the sides of your machine. Slide the water tank
out of your machine. Carry the water tank by its handle to the tap.
Step 7
Rinse
Unclip the cap, take the evaporator out of the water tank and rinse under a
cold tap.
Wipe away any excess water to avoid drips and place the evaporator to one
side.
Rinse the water tank under a cold tap. Wipe the inside of the tank to remove
any excess solution and any debris.
Step 8
Refill
Refill the water tank to the Max level and wipe off any excess water and
replace the cap, making sure that the cap clips are secured.
Step 9
Reassemble
Push the evaporator back into your machine, making sure that it is securely in
position.
Close the inner door and replace the outer covers.
Make sure the cap is completely dry. If wet, wipe thoroughly with a dry cloth.
Slide the water tank back into your machine and make sure it is securely in
place.
Changing your HEPA+Carbon filter
Supplied with a HEPA+Carbon filter.
To change your HEPA+Carbon filter, push down on the buttons on either side of
your machine to release the outer cover. Push down on the tabs to remove the
filter.
Push the replacement filter into the outer cover and make sure the tabs click
into place.
Put the outer covers into position on your machine and push firmly until they
both click securely into position.
Plugin and switch your machine, and reset your filter life.
The purifying humidifying fan with the filter covers open showing a HEPA plus
carbon filter located in the filter covers and a catalytic filter. Arrows
demonstrate that the catalytic filter is fitted directly to the base of the
machine and the filter covers will need to be assembled onto the base of the
machine.
Resetting your filter life
It’s important to reset your filter life after you have replaced your filter.
Press and hold the Night mode button on the remote control.
The LCD screen on your machine will count down from five, ending with default
screen.
The filter life has been reset and your machine is ready to use.
Looking after your machine
To always get the best performance from your Dyson purifying fan, it’s
important to regularly clean it and check for blockages.
Cleaning your machine
If your machine is dusty, wipe with a damp lint-free cloth.
Look for blockages in the air inlet holes on the filter and the small aperture
inside the loop amplifier.
Use a soft brush to remove dust and debris.
Don’t use detergents or polishes to clean your machine.
Alerts
Continuous alert icon
Switch off and unplug your machine.
Leave for 10 seconds and then plug your machine back in and switch it on.
If the alert icon continues to show on the LCD screen, contact Dyson.
Temporary alert icon
If the alert appears on the LCD screen and then disappears, continue to use
your machine.
If any other alert icons show on the LCD screen, contact Dyson for further
advice.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>