VONROC GG502DC Cordless Glue Gun Instruction Manual

VONROC GG502DC Cordless Glue Gun

SAFETY INSTRUCTIONS

Read the enclosed safety warnings, the additional safety warnings and the instructions. Failure to follow the safety warnings and the instructions may result in electric shock, fire and/or serious injury. Save the safety warnings and the instructions for future reference.

The following symbols are used in the user manual or on the product:

GENERAL SAFETY WARNINGS FOR POWER TOOLS IN HOUSEHOLD USE

• This glue gun is not intended for use by children and persons with physical, sensory or mental limitations or a lack of experience or knowledge. This glue gun can be used by children aged 8 or older and by persons who have physical, sensory or mental limitations or a lack of experience or knowledge if a person responsible for their safety supervises them or has instructed them in the safe operation of the glue gun and they understand the associated dangers. Otherwise, there is a danger of operating errors and injuries.
• Supervise children. This will ensure that children do not play with the glue gun.
• Children must not be allowed to clean and perform maintenance on the glue gun without supervision.

ADDITIONAL SAFETY INSTRUCTIONS FOR GLUE GUNS

• Do not allow persons unfamiliar with the glue gun or these instructions to operate the device.
• Before each use of the unit, check the glue gun, cable and plug. If damage is detected, do not use the glue gun. Never open the glue gun yourself, and have repairs carried out only by a qualified repair person using only identical replacement parts. Damaged glue guns, cables and plugs increase the risk of an electric shock.
• Do not leave the switched on glue gun unat­tended.
• Keep the glue gun away from rain or moisture.
• The penetration of water into the glue gun increases the risk of an electric shock.
• Do not touch the hot nozzle. Danger of burns. The mains plug of the glue gun must match the socket outlet. Never modify the plug in any way. Unmodified plugs and matching outlets will reduce the risk of electric shock.
• Do not misuse the cord to carry the glue gun, hang it up, or for pulling the plug out of the outlet. Keep the cord away from heat, oil, sharp edges or moving parts.
• Damaged or entangled cords increase the risk of electric shock. Have your glue gun repaired only through a qualified repair person and only using original replacement parts. This will ensure that the safety of the product is maintained.
• After use, place down the glue gun in a safe manner and allow it to cool down completely before packing it away. The hot nozzle can cause damage and/or burns.
• Do not use the cable for pulling the plug out of the socket outlet. Keep the cable away from heat or oil. Damaged or entangled cables increase the risk of an electric shock.

FOR THE CHARGER

Intended use
This glue gun has an integrated lithium-ion battery, which you can charge with the included USB charging cable (USB-mains adapter not included)

• The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of expe­rience and knowledge, unless they have been given supervision or instruction
• Children being supervised not to play with the appliance
• Do not recharge non-rechargeable batteries! During charging, batteries must be placed in a well ventilated area!
• Integrated batteries may only be removed for disposal by qualified personnel. Opening the housing shell can destroy the power tool. To remove the battery from the power tool, press the On/Off switch (6) until the battery is fully discharged. Unscrew the screws on the housing and remove the housing shell in order to remove the battery. To prevent a short circuit, disconnect the connectors on the battery one at a time and then isolate the poles. Even when fully discharged, the battery still contains a residual capacity, which can be released in case of a short circuit.

RESIDUAL RISKS
Even when the power tool is used as prescribed it is not possible to eliminate all residual risk factors. The following hazards may arise in connection with the power tool’s construction and design:

• Health defects resulting from vibration emission if the power tool is being used over longer period of time or not adequately managed and properly maintained.
• Injuries and damage to property to due to bro-ken accessories that are suddenly dashed.

MACHINE INFORMATION

Intended use
The glue gun is intended for the quick gluing of clean, dry and grease-free materials with hot-melt adhesives. The tool is intended for hobby use at home only.

TECHNICAL SPECIFICATIONS

DESCRIPTION

The numbers in the text refer to the diagrams on page 2-3.

1. Trigger
2. Base
3. Nozzle
4. Heat up LED indicator
5. On/off switch
6. Glue gun charging contacts
7. Battery and charger LED indicator
8. Base charging contacts
9. Drip tray
10. Micro USB charging port
11. Glue sticks
12. Charger cable

OPERATION

The machine must be charged before first use.Charging the device (Fig. B-C) Plug the charger cable (12) (included) into an adapter (not included). Plug the charger cable (12) in the micro USB charging port (10). See figure B

• Place the glue gun in to the base and make sure the glue gun charging contacts (6) and base charging contacts (8) are connected. See Fig. C.
• The charger LED indicator (7) will lighten up and show the charging status.

NOTE: Be sure that the metal contacts (6+8) in the glue gun and base are clean before charging.

LED Charger status
Red Battery charging in progress.
Green Battery charging finished, battery fully charged.

• After the battery is fully charged remove the charger plug from the outlet and remove the small plug from the base.
• Fully charging the battery may take up to 2 – 3 hours.

Inserting glue sticks (11) (Fig. D)
Always use the correct diameter glue stick.

1. Insert a glue stick through the opening at the back of the glue gun.
2. Guide the glue stick into the glue chamber until it stops.

The glue gun will stop dispensing glue when the glue stick in the chamber is almost used up. To refill the chamber, set the glue gun in the base and insert a new glue stick.

Switching the machine on and off (Fig. A)

• Press and hold the on/off switch (5) to turn on the glue gun until the heat up LED indicator (4) will light on in RED.
• Allow approx. 25 seconds for the glue to melt and reached the operating temperature and the heat up LED indicator (4) will turn green.
• The glue gun is ready for use.

NOTE: The heat up LED indicator appeared RED and you feel resistance from the trigger during application, then the glue gun will be required to reheating for a few seconds.

Using the glue gun

• Hold the glue gun firmly and place the nozzle close to the surface where glue will be applied.
• Pull the trigger (1) until glue flows from the nozzle (3), do not over-apply.
• When the desired amount of glue has been applied, release the trigger (1). Tilt the nozzle (3) slightly to the side and carefully pull the nozzle away from the object. This helps avoid strings of glue clinging to the work.
• Between application use the base to temporarily store the glue gun, glue gun will automatically charge.

NOTE: The glue gun will be automatically shut-off after approximately 5 minutes if not in use. You need to press the ON/OFF switch to restart.

Using the drip tray

• The built-in drip tray (9) on the base (2) will catch any drips while the glue gun is heating or cooling down.
• With your hand, simple to slide the drip tray out from base. Like shown in figure E.

NOTE: Always turn the glue gun off and place on its base when you are finished using the glue gun.

MAINTENANCE

Before cleaning and maintenance, always switch off the machine and remove the mains plug from the mains.

Clean the machine casings regularly with a soft cloth, preferably after each use. Make sure that the ventilation openings are free of dust and dirt. Remove very persistent dirt using a soft cloth moistened with soapsuds. Do not use any solvents such as gasoline, alcohol, ammonia, etc. Chemicals such as these will damage the synthetic components.

Clean the glue gun metal contact
Always check before each use to see that the metal contacts are clean to give a best contact performance when charging. Any residue should be cleaned from the metal contacts using the following steps.

1. Remove the glue gun from the base and set aside.
2. Carefully scrape the cooled glue from the metal contacts using a cotton swab or any non-metallic utensil.

Be sure to check the contacts on both the glue gun and the base for any glue residue. Never use metallic utensils to clean the contacts.

ENVIRONMENT
Faulty and/or discarded electrical or electronic apparatus have to be collected at the appropriate recycling locations.

Only for EC countries
Do not dispose of power tools into domestic waste. According to the European Guideline 2012/19/EC for Waste Electrical and Electronic Equipment and its implementation into national right, power tools that are no longer usable must be collected separately and disposed of in an environmentally friendly way.

WARRANTY

VONROC products are developed to the highest quality standards and are guaranteed free of defects in both materials and workmanship for the period lawfully stipulated starting from the date of original purchase. Should the product develop any failure during this period due to defective material and/or workmanship then contact VONROC directly.

The following circumstances are excluded from this guarantee:

• Repairs and or alterations have been made or attempted to the machine by unauthorized service centers;
• Normal wear and tear;
• The tool has been abused, misused or improperly maintained;
• Non-original spare parts have been used.

This constitutes the sole warranty made by company either expressed or implied. There are no other warranties expressed or implied which extend beyond the face hereof, herein, including the implied warranties of merchantability and fitness for a particular purpose. In no event shall VONROC be liable for any incidental or consequential dam-ages. The dealers remedies shall be limited to repair or replacement of nonconforming units or parts.

The product and the user manual are subject to change. Specifications can be changed without further notice.
WWW.VONROC.COM

References

• VONROC Gereedschap & Tuin artikelen

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>