SHOEI CWR-F2 Smoke Mirror Shield User Manual

Polski
Suomalainen
Svenska
MANUAL
shoei.com https://www.shoei-europe.com/uk/start

*The following drawings depict the CWR-F2 shield/visor.

The terms “right” and “left” in this manual are from the point of view of a rider who is wearing the helmet.

CWR-F2 / CWR-F2R Shield / Visor

If you pull the shield/visor completely down, it will be locked. It is recommended that the shield/visor remains in this position while riding your motorcycle. (Drawing A)
The fog can be removed by opening the shield/visor slightly as in Drawing B and riding a motorcycle at low speed to circulate air within the helmet.

WARNING
Do not ride a motorcycle at high speed with the shield/visor opened slightly. The shield/visor can be fully opened unexpectedly and can be very dangerous.
■ Opening the shield/visor
Press the shield/visor locking button to unlock the shield/visor, and then, open the shield/visor. (Drawing A)
■Removing the shield/visor

1. Open a shield/visor to a fully opened position as per Drawing 1.
2. While pulling the trigger down, pull the shield/visor toward the front of the helmet and hold up the shield/visor toward you to detach hooks (A) and (B) (Drawing 2).
3. Do in the same manner for the other side.

■Installing the shield/visor

1.  Adjust a shield/visor to a fully opened position and insert shield/visor hook (C) as per Drawing 4.

2. While pulling the shield/visor toward the front of the helmet, press an arrowed area of a shield/visor indicated in Drawing 5 until it clicks. Then, insert
   hooks (A) and (B) securely into the positions indicated in Drawing 6.

3. Do in the same manner for the other side.

4. Open and close a shield/visor a few times and make sure that all the hooks are fixed securely.

WARNING
If the hook and gear are not securely fastened in the shield/visor base, the shield/visor may come loose while riding and an accident may unexpectedly occur. After installing the shield/visor, open and close the shield/visor a few times to confirm that the hook and gear fit securely. With the shield/visor completely closed, confirm that the shield/visor locking knob engages with the shield/visor hook.

Replacement of CWR-F2 Shield / Visor Base

1. Remove a shield/visor. Then, remove 4 screws to remove the CWR-F2 Shield / Visor Base. Fix a replacement CWR-F2 Shield / Visor Base as follows.
2. Align a center of a hole in the bottom of the CWR-F2 Shield / Visor Base to a hole in a bottom of a shell and tighten a screw.
3. Then, align a center of a hole on the top of the CWR-F2 Shield / Visor Base to a hole in a top of a shell and tighten a screw.
4. Do in the same manner for the other side. Refer to <<Important Notice about Handling the CWR-F2 / CWR-F2R Shield / Visor>> for the extent and way of tightening.
5. Fix a shield/visor
6. Open and close a shield/visor a few times and make sure that all the hooks (A), (B), and (C) are fixed securely.

Adjusting CWR-F2 / CWR-F2R Shield / Visor

If a shield/visor doesn’t touch a window beading closely or doesn’t close after replacement of a shield/visor or CWR-F2 Shield / Visor Base, adjust CWR-F2 Shield / Visor Base in the following manner.

Check Point A:
Whether an inside of a top end of a shield/visor is in close touch with a window beading;

Check Point B:
Whether a bottom end of a shield/visor is in close touch with a lip of a window beading;
■In case a gap still remains after adjustment with a shield/visor adjustment lever: ❼Reset shield/visor adjustment levers of both sides to positions in the drawing. Loosen both screws on a right side of a helmet and move the CWR-F2 shield/visor base slightly toward the direction indicated in the drawing. Tighten the screws and fix it. Install the shield/visor and check that the window bead completely seals up around the shield/visor. ■In case a gap still remains even after adjusting up to ❼: ❽If the gap still remains, follow the same procedure to adjust the position of the CWR-F2 shield/visor on a left side of a helmet.

WARNING

With the shield/visor completely closed, check that the shield/visor is locked after adjusting the position of the CWR-F2 shield/visor base. If the CWR-F2 shield/visor base is positioned extremely toward the back, the shield/visor may not be locked.

Shield/visor adjustment lever

During usage, if a gap occurs between the shield/visor and the window beading even when the shield/visor is closed, lower the adjustment levers of the shield/visor base as shown in the drawing, and you can reduce the gap between them. There are levers on the left and right and they can each be used for adjustment.
By default, the adjustment levers are set in the standard positions. By setting the adjustment levers in the adjusted positions, the shield/visor moves backward.
If a shield/visor is adjusted too tight, a window beading may deteriorate. Make adjustments by watching a condition of a gap carefully.
*In case, the gap even remains by using the shield/visor adjustment lever, loosen the screws to adjust the position of the shield/visor base.

CWR-F2R Tear-off Button

CWR-F2R Tear-off Button is used to equip CWR-F2R Tear-off Film (optional) for races. Please note that the CWR-F2R tear-off buttons are not attached to the CWR-F2 shield/visor.
When damaged, it may be replaced with an optional CWR-F2R Tear-off Button.
When using CWR-F2R Tear-off Film (optional), adjustment of the Tear-off Button is required before fixing the Tear-off Film. Manual enclosed in CWR-F2R Tea- off Film explains how to adjust or how to affix.
*****Tear-off Button turns anticlockwise. Don’t turn it clockwise.

Important Notice about Handling the CWR-F2 / CWR-F2R Shield / Visor

1. Dirt and scratches on the shield/visor may obstruct your view while riding and can be very dangerous! If the shield/visor gets dirty or scratched, stop using it immediately. Remove the shield/visor and clean or replace it.
2. The shield/visor should be cleaned with a solution of mild, neutral soap and water. Rinse well with pure water then wipe dry with a soft cloth. Do not use any of the following cleaning materials: hot water over 40℃; saltwater; any acidic or alkali detergent; benzine, thinner, gasoline, or other organic solvents; glass cleaner; or any cleaner containing organic solvents. If any of these cleaners are used, the shield’s/visor’s chemical nature may be altered and safety may be hindered.
3. Do not ride with a shield/visor that is fogged. This may obstruct your view and can be very dangerous. If the shield/visor is fogged, open the lower air intake to circulate air within the helmet and remove the fog from the shield/visor. The use of the PINLOCK©  EVO lens is also effective in stopping fog.
4. Always use SHOEI’s genuine PINLOCK © EVO lens for CWR-F2/CWR-F2R. For fitting the PINLOCK © EVO lens, please read the instructions enclosed in it.
5. After cleaning or replacing the base plates, close the shield/visor and make sure that it touches the window beading all around. If there is a gap between the shield /visor and the window beading, adjust the position of the base plate and eliminate the gap, because it may cause a roll-in of wind or noise.
6. For tightening screws, apply the No.2 size Phillips head screwdriver vertically and rotate it carefully. If an improperly sized screwdriver or electric screwdriver is used, a screw head may be broken. Use a genuine screw made of aluminum for replacement. If a screw is tightened too much, it may be broken. (Recommended torque: 0.8 N.m or about 8 kgf. cm)Size(No.2)
7. Do not place stickers or adhesive tape on the shield/visor.

357
Printed in Japan 20210128
HEAD OFFICE 8th Floor, 1-31-7 Taito, Taito-Ku, Tokyo 110-0016, JAPAN
Tel: +81 3 5688 5170　Fax: +81 3 3837 8245
SHOEI SAFETY HELMET CORPORATION 3002 Dow Avenue, Suite 128, Tustin, California 92780, U.S.A.
Tel: +1 714 730 0941　Fax: +1 714 730 0942
SHOEI Distribution GmbH Elisabeth-Selbert-Straße 13, 40764 Langenfeld, Germany
Tel: +492173 39975-0　Fax: +492173 39975-66

References

• kgf.cm
• SHOEI WORLDWIDE
• SHOEI WORLDWIDE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>