MOZA AirCross 3 and AirCross 3 Pro User Manual
- June 3, 2024
- Moza
Table of Contents
AirCross 3 & AirCross 3 Pro
User Manual
AirCross 3 and AirCross 3 Pro
Dear customer,
Thank you for purchasing our product. Please read the following instructions
carefully before first use and keep this user manual for future reference. Pay
particular attention to the safety instructions. If you have any questions or
comments about the device, please contact the customer line.
www.alza.co.uk/kontakt
+44 (0)203 514 4411
Importer
Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Prague 7,
www.alza.cz
MOZA AirCross 3/Pro Overview
1. Tilt Motor Lock | 13. USB-C Charging Port |
---|---|
2. Extension Port | 14. Battery Indicator Light |
3. Quick Release Plate | 15. Power Button |
4. Tilt Adjustment Slider | 16. OLED Screen |
5. Pan Motor Lock | 17. Joystick |
6. Foldable Safety Lock | 18. 1/4” Extension Port |
7. Smart Trigger | 19. Camera Control Port |
8. Quick Release Plate Knob | 20. AI Extension Port |
9. Quick Release Baseplate Knob | 21. Tilt knob |
10. Roll Knob | 22. Foldable Knob |
11. Roll Motor Lock | 23. Camera Control Button |
12. Pan Knob | 24. Function Button |
Preparation
Unfold the Gimbal
- Rotate the foldable Knob.
- Unfold the handle until it is locked.
- Tighten the knob to prevent the handle from loosening.
Attaching the Tripod
-
Screw the mini tripod into the screw hole at the bottom of the handle.
-
Expand the mini tripod
Battery Charging
Please charge the battery through the USB-C charging port using a USB-C cable
(Included) and a USB adapter (Not included). It is recommended to use a USB
adapter with QC2.0 or PD protocol to complete the charging quickly. The LED
light below the charging port will switch of after the charging is completed.
Unlock the Gimbal
Rotate the motor lock to the unlocked position, and then each motor can rotate
freely.
Make sure to prepare the camera before mounting, confirm the battery is fully charged and a memory card with sufficient storage space is inserted.
-
Place the camera on the quick-release plate with 1/4″ or 3/8” screws and keep the camera in the center. Remove the extra screws as a spare.
-
Slide the quick release plate onto the baseplate to the locked position.
-
Secure the quick-release plate and tighten the knob, make sure the quick-release plate is locked.
Note:
- When installing the camera, if the right side of the camera interferes with the tilt arm causing the installation to fail, loosen the knob of the quick-release baseplate and move it to the left until the camera can be installed successfully.
- After the camera is installed, move the quick-release baseplate to the right and make sure the camera’s right side is aligned with the tilt arm to achieve the best stability.
Balance Adjustment
1. Balancing the tilt axis vertically.
- Rotate the camera so that the lens is pointing upward.
- Unlock the tilt axis and loosen the knob, slightly adjusting the position of the tilt adjustment slider.
- The balancing is completed when the camera is steady while pointing upward, lock the tilt axis.
2. Balancing the tilt axis horizontal
- Rotate the camera so that lens is pointing forward.
- Unlock the quick-release plate, and slightly adjust the position of the plate.
- The balancing is completed when the camera is steady while pointing forward, lock the quick-release plate.
3. Balancing the Roll Axis
- Unlock the Roll axis.
- Slightly adjust the roll arm left and right until it’s completely horizontal.
- Lock the roll axis.
4. Balancing the Pan Axis
- Hold the gimbal at an angle of 45° horizontally, and turn the pan arm to a horizontal angle.
- Unlock the Pan axis and slightly adjust the pan arm left and right.
- The Pan axis is balanced when the camera is steady, lock the pan axis.
Operation
|
Power Button
Long press: Power on or off
One-click: Switch the follow speed, 5 levels from slow to fast
Double-click: Enter or exit sleep mode.
---|---
|
Joystick
Control the rotation of the gimbal
Menu:
Top Button: Option-up
Down Button: Option-down
Left Button: Return
Right Button: Confirm
| Camera Control Button
Press halfway: Autofocus
One-click: Start recording
Press and hold for 3 seconds: take a photo
| Function Button:
One Click: Follow mode (Pan-Tilt Follow, All Lock)
Double Click: Sport Gear Mode
Triple Click: Inception Mode
Long Press: Enter/Exit Menu
| Trigger Button
One Click: Start/Stop AI Follow Mode
Double Click: Re-centre
Triple Clicks: Selfie Mode
Press and Hold: All Lock
One Click and Hold: Pan-tilt Follow
Advanced Features
Please visit www.gudesn.com for the complete user manual. It will guide you:
- Language Switch
- Camera Control
- Button Customization
- Motor Output
- FPV, Sports Gear Mode, Manual Positioning
- User Configuration
- Calibration and Firmware Updated
MOZA Master App
Scan the code or search in the app store to download the MOZA Master App. MOZA Master provides functions like Virtual Joystick Control, Motion Sensing Control, Parameter setting, Time-Lapse, Panorama, Calibration, and Firmware Updated.
Specification
Model | AirCross 3 / AirCross 3 Pro |
---|---|
Weight | 1.3kg without a tripod |
Dimension (WDH) | Unfold: 170190310 mm Folded: 52225270 mm |
Battery Type | Li-ion intelligent Battery (built-in), 24.718Wh |
Battery Capacity | 3400mAh |
Standard Voltage | 7.27V |
Charging Voltage | 5V/2A, 9V/2A |
Working Hours | 20H |
Fast-charging time | 1.4H |
Bluetooth | 2.400 GHz -24835 GHz |
Environmental requirements | Working temperature: -10°C -50°C Charging |
temperature: 5°C -40°C
Safety Caution
- This power is powered by a built-in battery, please do not disassemble it, and do not put it into liquid or fire in order to avoid damage or risk of injury.
- Before powering on the gimbal, please adjust the balance following the instructions in this document. If the gimbal works in an unbalanced state for a long time, the surface temperature of the motor can get hot, which will seriously shorten the battery life.
- Do not let children touch and use this product, and do not use fingers to obstruct the motor operation to avoid finger injury.
- This product is not waterproof or dustproof, please keep the gimbal clear of dust and water to avoid damage.
Warranty Conditions
A new product purchased in the Alza.cz sales network is guaranteed for 2 years. If you need repair or other services during the warranty period, contact the product seller directly, you must provide the original proof of purchase with the date of purchase.
The following are considered to be a conflict with the warranty conditions,
for which the claimed claim may not be recognized:
- Using the product for any purpose other than that for which the product is intended or failing to follow the instructions for maintenance, operation, and service of the product.
- Damage to the product by a natural disaster, the intervention of an unauthorized person, or mechanically through the fault of the buyer (e.g., during transport, cleaning by inappropriate means, etc.).
- Natural wear and aging of consumables or components during use (such as batteries, etc.).
- Exposure to adverse external influences, such as sunlight and other radiation or electromagnetic fields, fluid intrusion, object intrusion, mains overvoltage, electrostatic discharge voltage (including lightning), faulty supply or input voltage, and inappropriate polarity of this voltage, chemical processes such as used power supplies, etc.
- If anyone has made modifications, modifications, alterations to the design, or adaptations to change or extend the functions of the product compared to the purchased design or use of non-original components.
EU Declaration of Conformity
Identification data of the manufacturer’s / importer’s authorized
representative:
Importer: Alza.cz a.s.
Registered office: Jankovcova 1522/53, Holešovice, 170 00 Prague 7
CIN: 27082440
The subject of the declaration:
Title: Stabilizer
Model / Type: AirCross 3 & AirCross 3 Pro
The above product has been tested in accordance with the standard(s) used
to
demonstrate compliance with the essential requirements laid down in the
Directive(s):
Directive No. 2014/53/EU
Directive No. 2011/65/EU as amended 2015/863/EU
WEEE
This product must not be disposed of as normal household waste in accordance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE – 2012/19 / EU). Instead, it shall be returned to the place of purchase or handed over to a public collection point for the recyclable waste. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. Contact your local authority or the nearest collection point for further details. Improper disposal of this type of waste may result in fines in accordance with national regulations.
References
- Alza.cz – rychlý a pohodlný nákup odkudkoliv | Alza.cz
- Alza | Alza.co.uk
- Alza.cz – rychlý a pohodlný nákup odkudkoliv | Alza.cz
- Alza.cz – rychlý a pohodlný nákup odkudkoliv | Alza.cz
- Alza.cz
- alza.de
- alza.hu
- alza.sk
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>