LITE ON NIUS 802.11 b/g/n, 1T1R 2.4GHz Module User Manual

LITE ON NIUS 802.11 b g n 1T1R 2 4GHz Module
USER MANUAL
802.11 b/g/n, 1T1R 2.4GHz Module
Model: NIUS WN3602M-PLUS (3.3V/5V)
NXP 88MW320
Version 1.0

PRODUCT FEATURES

• IEEE 802.11b/g/n, 1×1 SISO 2.4 GHz
• Compact Form Factor: 30x17x1mm (PCB) ±0.1mm
• Integrated CPU, memory, MAC, DSSS/OFDM baseband, direct conversion RF radio, encryption
• CMOS and low-swing sine wave input clock
• Low-power with deep sleep and standby modes
• Integrated T/R switch, PA, and LNA
• HF/RoHS compliance

PRODUCT SPECIFICATIONS

MAIN CHIPSET
NXP 88MW320-A0-NAPE/AZ

FUNCTIONAL SPECIFICATIONS

WiFi Function

802.11g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps
802.11n: MCS 0 to 7
Media Access Control| CSMA/CA with ACK
Modulation Techniques| 802.11b: CCK, DQPSK, DBPSK
802.11g: 64QAM, 16QAM, QPSK, BPSK
802.11n: BPSK, QPSK, 16QAM, 64QAM
Network Architecture| Ad-hoc mode (Peer-to-Peer)
Infrastructure mode
Operation Channel| 2.4GHz
11: (Ch. 1-11) – United States
13: (Ch. 1-13) – Europe
14: (Ch. 1-14) – Japan
Frequency Range| 802.11bg
2.412 ~ 2.462 GHz
Transmit Output Power – 1×1(Tolerance: +-1.5dBm)| 802.11b: 11b(1M~11M) :16dBm
| 802.11g:
11g(6M~18M) :16dBm
11g(24~54M): 15dBm
802.11n:
11n(MCS0~MCS7) :13dBm
Receive Sensitivity| 802.11b: (IEEE Standard <-76dBm)
typical: -87.5dBM(1M)
802.11g: (IEEE Standard <-65dBm)
Typical: -73dBm(54M)
802.11n: 20MHz (IEEE Standard <-64dBm)
Typical: -71dBm
Security| WPA, WPA2, WPS, WEP 64/128, IEEE 802.11x, IEEE 802.11i
Operating Voltage| 5V or 3.3V ±10% supply voltage
Power Consumption
(Average)| 165mA@16dBm
Antenna Type| Printed Antenna

PIN DEFINITION

PIN| Name| Type|
---|---|---|---
1| UART2 RX| I|
2| UARTO RX| I|
3| UARTO TX| 0|
4| 5V| P| 5V Power in
5| 3.3V| P| 3.3V Power in
6| GND| GND| Ground
7| RESET| I| IC Reset
8| BOOT| I/O|
9| GPI010| I| JTAG-TRST
10| GPIO9| I| JTAG-TDI
11| GPIO8| I/O| JTAG-TMS
12| GPIO7| I| JTAG-CLK
13| GPIO6| 0| JTAG-TDO
14| UART1 RX| I|
15| UART1 TX| 0|
16| UART2 TX| 0|

MECHANICAL

WN3602M (3.3V)

WN3602M (5V)

Unit : mm ; Tolerance : +/- 0.1mm

RECOMMEND FOOTPRINT

ENVIRONMENTAL

Operating
Operating Temperature: 0 to 70 °C
Relevant Humidity: 5-90% (non-condensing)
Storage
Temperature: -40 to 85 °C
Relevant Humidity: 5-95% (non-condensing)

WARNINGS

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.
For products available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20cm between the radiator & your body.

ISED Statement
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development
Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

This module is intended for OEM integrators under the following conditions:

1. Ensure that the end-user has no manual instructions to remove or install-module.
2. This module is certified pursuant to Part 15 rules section 15.247 and RSS-247.
3. This module has been approved to operate with the antenna types listed below, with the maximum permissible gain indicated.

Antenna| Frequency Band| Antenna Type| Brand| Model
Number| Gain(dBi)
---|---|---|---|---|---
1| 2400-2483.5MHz| Printed Antenna| LITEON| WN3602M| -0.9

4. Label and compliance information
Label of the end product:
FCC
The host product must be labeled in a visible area with the following ” Contains FCC ID: 2AIBX-NIULL”.
The end product shall bear the following 15.19 statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
ISED
This transmitter module is authorized only for use in devices where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final  end product must be labeled in a visible area with the following: “Contains transmitter module IC: 21700-NIULL” or “Contains IC: 21700-NIULL” Content le module d’émission IC: 21700-NIULL

5. Information on test modes and additional testing requirements
This module has been approved under a stand-alone configuration.
OEM integrator has to be limited the operation channels in channels 1-11 for the 2.4GHz band.
The separate approval is required for all other operating configurations, including portable configurations with respect to Part
2.1093/RSS-102 and different antenna configurations
The information on how to configure test modes for host product evaluation for different operational conditions for a stand-alone modular transmitter in a host, versus with multiple, simultaneously transmitting modules or other transmitters in a host can be found at KDB Publication 996369 D04.
OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the  FCC/ISED authorization is no longer considered valid and the FCC/IC No. cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC/ISED authorization.

6. Additional testing, Part 15 Subpart B and ICES-003 disclaimer
Appropriate measurements (e.g. Part 15 Subpart B compliance) and if applicable additional equipment authorizations (e.g. SDoC) of the host product to be addressed by the integrator/manufacturer.
This module is only FCC/ISED authorized for the specific rule parts 15.247, RSS-247 listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC/ISED rules that apply to the host product as being Part 15 Subpart B/ICES-003 compliant.

7. The user manual of the end product should include:
FCC:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter.

ISED:
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.
ISED Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

References

• Anatel — Agência Nacional de Telecomunicações

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>