LITE-ON WCBN3610L Wireless IOT Module User Manual
- June 16, 2024
- LITE ON
Table of Contents
LITE-ON WCBN3610L Wireless IOT Module
Product Information
- Specifications
- Model Name: WCBN3610L
- Wireless Standard: 802.11 b/g/n
- Frequency Range: 2.412 ~ 2.462 GHz
- Operating Temperature: -20 to 85°C
- Operating Humidity: 5-90% (non-condensing)
- Storage Temperature: -40 to 85°C
- Storage Humidity: 5-95% (non-condensing)
- Product Features
- The WCBN3610L is a wireless IOT module that supports the 802.11 b/g/n standard.
- It operates in the 2.4GHz frequency range and has a maximum peak gain of 0.5.
- The module is designed for OEM integrators and complies with relevant regulations to ensure safe and reliable operation.
- Warnings
- ISED Statement:
- This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
- ISED Radiation Exposure Statement:
- This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. It should be installed and operated with a minimum distance of 20cm between the radiator and the user’s body.
- OEM Integrator Conditions:
- Ensure that the end user has no manual instructions to remove or install the module.
- This module is certified under Part 15 rules section 15.247 and RSS-247.
- Supported Antenna
- Antenna Number: Antenna 1
- Brand Name: LITEON
- Model Name: WCBN3610L
- Antenna Type: Printed Ant Murata
- Support: 2.4G
- Max Peak Gain: 0.5
Product Usage Instructions
- Installation
- Ensure that the device is powered off and disconnected from any power source.
- Locate an appropriate location for the module installation.
- Connect the antenna to the designated connector on the module.
- Carefully insert the module into the compatible slot or interface of your target device.
- Operation
- Ensure that the device is powered on and connected to a power source.
- Follow the instructions provided by your target device to configure the wireless settings.
- The WCBN3610L module will establish a wireless connection in the 2.4GHz frequency range.
- You can now use the wireless capabilities of your target device as intended.
- Maintenance
- To ensure optimal performance and longevity of the WCBN3610L module, follow these maintenance guidelines:
- Keep the module clean and free from dust or debris.
- Avoid exposing the module to extreme temperatures or humidity.
- Regularly check for any loose connections and reattach if necessary.
- Refer to the user manual of your target device for any specific maintenance instructions.
FAQs
- Q: What is the frequency range of the WCBN3610L module?
- A: The WCBN3610L module operates in the 2.4GHz frequency range.
- Q: Can I install the module myself?
- A: The module is intended for OEM integrators and should be installed by professionals or individuals with proper knowledge and experience.
- Q: What is the maximum peak gain of the supported antenna?
- A: The supported antenna has a maximum peak gain of 0.5.
PRODUCT FEATURES
- WiFi operates at ISM frequency bands (2.4GHz)
- Compact Form Factor: 18 x 20.5 x 3.2 mm ±0.1mm
- A bunch of UART/ SPI/ I2C interfaces for peripheral controllers
- Standards support: 802.11b, 802.11g, 802.11n, 802.11d, 802.11e, 802.11i
- Enterprise-level security complying with WPA/WPA2 certification
- Lightweight TCP/IP protocol suite
- One transmitter and one receiver 802.11n WLAN transceiver supports up to 150 Mbps downstream and 150 Mbps upstream PHY rates
- ARM Cortex-M development environment for customer applications
- HF/RoHS compliance
PRODUCT SPECIFICATIONS
MAIN CHIPSET
- MAC/ Baseband/ RF: RTL8720CM
FUNCTIONAL SPECIFICATIONS
ENVIRONMENTAL
- Operating
- Operating Temperature: -20 to 85 C Relevant Humidity: 5-90% (non-condensing)
- Storage
- Temperature: -40 to 85 C
- Relevant Humidity: 5-95% (non-condensing)
FCC
WARNINGS
FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in
conjunction with any other antenna or transmitter. For products available in
the USA/Canada market, only channels 1~11 can be operated. Selection of other
channels is not possible.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator & your body.
ISED Statement
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science, and Economic Development Canada’s license-exempt
RSS(s).
Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
ISED Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20cm between the radiator & your body.
For products available in the USA/Canada market, only channels 1~11 can be operated. Selection of other channels is not possible.
This module is intended for OEM integrators under the following conditions:
- Ensure that the end user has no manual instructions to remove or install the module.
- This module is certified under Part 15 rules section 15.247 and RSS-247.
- This module has been approved to operate with the antenna types listed below, with the maximum permissible gain indicated.
Antenna Number| Brand Name| Model Name| Ant. Type|
Connector| Support| Max Peak Gain
---|---|---|---|---|---|---
Antenna 1| LITEON| WCBN3610L| Printed Ant| Murata| 2.4G| 0.5
4 Label and compliance information
Label of the end product: FCC
- The host product must be labeled in a visible area with the following ” Contains FCC ID: PPQ-WCBN3610L”.
- The end product shall bear the following 15.19 statement: This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
USED
This transmitter module is authorized only for use in devices where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The end product must be labeled in a visible area with the following: “Contains transmitter module IC: 4491A-WCBN3610L” or “Contains IC: 4491A-WCBN3610L”
Information on test modes and additional testing requirements
This module has been approved under stand-alone configuration. OEM integrator
has limited the operation channels in channels 1-11 for the 2.4GHz band.
Separate approval is required for all other operating configurations,
including portable configurations concerning Part 2.1093/RSS-102 and different
antenna configurations The information on how to configure test modes for host
product evaluation for different operational conditions for a stand-alone
modular transmitter in a host, versus with multiple, simultaneously
transmitting modules or other transmitters in a host can be found at KDB
Publication 996369 D04. OEM integrator is still responsible for testing their
end product for any additional compliance requirements required with this
module installed (for example, digital device emissions, PC peripheral
requirements, etc.).
IMPORTANT NOTE: If these conditions cannot be met (for example certain
laptop configurations or co-location with another transmitter), then the
FCC/ISED authorization is no longer considered valid, and the FCC/IC No.
cannot be used on the final product. In these circumstances, the OEM
integrator will be responsible for re-evaluating the end product (including
the transmitter) and obtaining a separate FCC/ISED authorization.
Additional testing, Part 15 Subpart B and ICES-003 disclaimer
Appropriate measurements (e.g. Part 15 Subpart B compliance) and if applicable
additional equipment authorizations (e.g. SDoC) of the host product to be
addressed by the integrator/manufacturer. This module is only FCC/ISED
authorized for the specific rule parts 15.247, and RSS-247 listed on the
grant, and the host product manufacturer is responsible for compliance with
any other FCC/ISED rules that apply to the host product as being Part 15
Subpart B/ICES-003 compliant
The user manual of the end product should include: the FCC
- Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
- The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons.
- This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter.
ISED: This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license- exempt RSS(s).
Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
ISED Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20cm between the radiator & your body.
For products available in the USA/Canada market, only channel 1~11 can be
operated. Selection of other channels is not possible.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>