AV Access HDW100 1080P Wireless HDMI Extender User Manual
- June 5, 2024
- AV Access
Table of Contents
HDW100
1080P Wireless HDMI Extender
User Manual
Disclaimers
The information in this manual has been carefully checked and is believed to
be accurate. AV Access Technology Limited assumes no responsibility for any
infringements of patents or other rights of third parties which may result
from its use.
AV Access Technology Limited assumes no responsibility for any inaccuracies
that may be contained in this document. AV Access Technology Limited also
makes no commitment to update or to keep current the information contained in
this document.
AV Access Technology Limited reserves the right to make improvements to this
document and/or product at any time and without notice.
Copyright
Copy, Reproduce, Distribute, and/or Edit of this document or part of it as
well as utilization of its contents and communication thereof to others
without express authorization are prohibited. Offenders will be held liable
for the payment of damages. All rights created by patent grant or
registration of a utility model or design patent are reserved. Copyright ©2017
AV Access Technology Limited All rights reserved.
Trademarks Notice
All products or service names mentioned in this document may be trademarks of
the companies with which they are associated.
Contact Us
Email: [email protected]
Important Safety Instructions
- Do not expose this device to rain, moisture, dripping, or splashing. No objects filled with liquids, such as vases, shall be placed on the device.
- Do not install or place this unit in a bookcase, built‐in cabinet, or in another confined space. Ensure the unit is well ventilated.
- To prevent the risk of electric shock or fire hazard due to overheating, do not obstruct the unit’s ventilation openings with newspapers, tablecloths, curtains, or similar items.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other devices (including amplifiers) that produce heat.
- Do not place sources of naked flames, such as lighted candles, on the unit.
- Clean this device only with a dry cloth.
- Unplug this device during lightning storms or when unused for long periods of time.
- Protect the power cord from being walked on or pinched, particularly at plugs.
- Only use attachments/accessories specified by the manufacturer.
- Refer all servicing to qualified service personnel.
Introduction
Overview
The 1080P Wireless HDMI extender set extends HDMI signals from a source device
to a display device wirelessly up to 200 meters or through a Cat 5e/6 cable up
to 120
meters. Great for homes and offices.
Features
- Transmits 1080P HDMI signals up to 200 meters wirelessly.
- Transmits 1080P HDMI signals up to 120 meters through a Cat 5e/6 cable.
- HDMI loop‐out on the transmitter to connect to a local display allows easy monitoring of the source signal.
- IR extension allows you to control the source device from a remote location.
Package Contents
Before you start the installation of the product, please check the
package contents:
1 x Transmitter; 1 x Receiver; Others: 2 x Antennas; 2 x Power Adapters (DC 5V
1A);
2 x Exchangeable US Plugs; 1 x IR Emitter; 1 x IR Receiver; 4 x Mounting Ears
(with Screws); 1 x User Manual
Application
Note:
| “Work Mode” Switch Settings | Fig 1 | Fig 2 |
|---|---|---|
| Transmitter | Wireless | Wire |
| Receiver | Wireless | Wire |
Panel Layout
Installation
The device can be placed on a stable surface. To install the device in a suitable location, perform the following:
- Position and install the mounting brackets using the mounting screws provided.
- Repeat the above step for the other side of the device.
- Attach the brackets to the surface you want to hold the device against using the screws (not included).
Specifications
Technical
Input A/V Port| Transmitter: 1 x HDMI
Receiver: 1 x LAN, 1 x WLAN
Input Resolutions| Up to 1080P@60Hz
Output A/V Port| Transmitter: 1 x HDMI, 1 x LAN, 1 x WLAN
Receiver: 1 x HDMI
Output Resolutions| Up to 1080P@60Hz
Compliance| HDMI 1.3, HDCP 1.4
transmission distance| Wireless: 200m/656ft (line of sight)
Wired: 120m/394ft
General
Operating
Temperature| +32°F ~ +113°F (0°C ~ +45°C)
10% ~ 90%, non‐condensing
Storage Temperature| ‐4°F ~ 140°F (‐20°C ~ +70°C)
10% ~ 90%, non‐condensing
Power Supply| DC 5V 1A
Power Consumption| TX: 3.5W (Max) RX: 1.6W (Max)
ESD Protection| Human body model:
• ±8kV (air‐gap discharge)
• ±4kV (contact discharge)
Product
Dimension (W x H x D)| 140mm x 21mm x 80mm/5.5” x 0.83” x 3.15″ each for TX
and RX (Antennas not included)
Net Weight| TX: 0.31kg; RX: 0.30kg
Gross Weight| 1.10kg
FAQs
-
What should I do when the Link LED is on, but there’s no video output on the remote display?
• Check and ensure the Work Mode switches on both transmitter and receiver(s) are set to the same positions (both at “Wireless” or “Wire”).
• Check and ensure the HDMI source is powered on, and the transmitter’s HDMI In LED is on.
• Connect the HDMI source device directly to the display to see if there’s signal output. -
How to deal with poor video quality?
• Check if the HDMI cables are connected properly. Use different HDMI cables if necessary.
• Change the angles of the antennas on the transmitter and receiver to make the antennas parallel to each other (refer to Fig a). Operation in Fig b&c is not recommended.
• Decrease the distance between the
transmitter and receiver to ensure it is within the available transmission
range.
• Remove other wireless signals and move any obstacles that are blocking the signal line‐of‐sight. -
Why does the IR remote controller seem not sensitive enough?
Avoid pressing and holding the IR remote controller’s buttons. Try to short press them intermittently instead.
Warranty
Products are backed by limited 1‐year parts and labor warranty. For the following cases, AV Access Technology Limited shall charge for the service(s) claimed for the product if the product is still remediable and the warranty card becomes unenforceable or inapplicable.
- The original serial number (specified by AV Access Technology Limited) labeled on the product has been removed, erased, replaced, defaced, or is illegible.
- The warranty has expired.
- The defects are caused by the fact that the product is repaired, dismantled, or altered by anyone that is not from an AV Access Technology Limited authorized service partner. The defects are caused by the fact that the product is used or handled improperly, roughly, or not as instructed in the applicable User Guide.
- The defects are caused by any Force Majeure including but not limited to accidents, fire, earthquake, lightning, tsunami, and war.
- The service, configuration, and gift s promised by the salesman only but not covered by a normal contract.
- AV Access Technology Limited reserves the right to interpret these cases above and to make changes to them at any time without notice. Thank you for choosing products from AV Access.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to a radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. The
distance between user and products should be no less than 2ocm
IC Statement
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science, and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions: (1) This device
may not cause interference. (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
Distance Statement
The distance between user and products should be no less than 20CM.
www.avaccess.com [email protected]