Satel INT-TSG2 4.3 Inch Touchscreen Keypad User Manual
- June 5, 2024
- Satel
Table of Contents
Satel INT-TSG2 4.3 Inch Touchscreen Keypad User Manual
INT-TSG2
SATEL sp. z o.o. • ul. Budowlanych 66 • 80-298 Gdańsk • POLAND
tel. +48 58 320 94 00
www.satel.eu
Full manual is available at www.satel.eu. Scan the QR code to go to our website and download the manual.
Changes, modifications or repairs not authorized by the manufacturer shall void your rights under the warranty.
The declaration of conformity may be consulted at www.satel.eu/ce
The following symbols may be used in this manual:
– note,
– caution.
This manual contains basic information on how to use the INT-TSG2 keypad with factory default settings. The functions available in the user menu of the keypad allow you to control your alarm system, regardless of its configuration. In addition, the user screens can be prepared by the installer for customization of the keypad functionality. The installer can create new user screens and add widgets that you will use for day to day operations of the alarm system. The installer may also personalize the look of the screen to better suit your preferences in terms of widget, font and background colors. Pictures selected by you may be used as the background image.
Ask the installer for instructions on how to use your individually configured keypad.
The instructions must include all the changes from the default settings. The
installer should
also instruct you on how to operate the alarm system by using the INT-TSG2
keypad.
1. LED indicators
2. Using the touch screen
The touch screen displays information about the system status, while allowing
you to operate
and program the alarm system, as well as control the home automation
equipment.
In order to control the alarm system, you can use:
- user screens and additional screens created for you by the installer,
- user menu created by SATEL.
After 10 minutes of inactivity, the keypad screen can turn off (this setting
is available in the
service menu). Use the gestures described below.
Swipe up / down
Tap the screen and slide your finger up or down to:
-
swipe the screen up / down (move between the screensaver / user screen / user menu
home screen), -
scroll through a list.
Swipe right / left
Tap the screen and slide your finger right or left to swipe the screen right /
left (go to the previous / next screen). When the screensaver is active, swipe
right / left to start / end the slide show.
Swipe right from the edge (return to the previous screen)
Tap the screen close to the left edge and slide your finger right to return to
the previous screen. This gesture is supported in the user menu and the
service menu. You will not be able to exit the service mode by using this
gesture.
3. Screensaver
The screensaver is displayed:
- when you swipe down on the user screen,
- when you swipe right on the slide show,
- 60 seconds after the last operation is performed on the screen (except when in the service menu).
You will be logged out when the screensaver is displayed.
The screensaver on a keypad with factory default settings (Fig. 1) shows the
date and time.
The installer can add to the screen additional widgets that will indicate the
alarm system status (see “Widgets” p. 7).
Tap the screen to view the user screen.
Swipe left to start the slide show.
3.1 Slide show
The keypad can run a slide show of images, if the installer installed in the
keypad a memory
card on which the images had been saved.
Tap the screen to view the user screen.
Swipe right to view the screensaver.
3.2 Trigger the panic alarm
When the screensaver or slide show is displayed, tap the screen and hold for 3
seconds to trigger the panic alarm. The installer defines whether the alarm
triggered will be loud (signaled by the alarm system) or silent (without
signaling). The silent panic alarm is useful when the control panel reports
events to the monitoring station, but unauthorized persons should not be aware
of the alarm being triggered.
4. User screens
When the screensaver or slide show is displayed, tap the screen to go to the user home screen. Only one user screen is available in the keypad with factory default settings. The installer can add more user screens and set one of them as the user home screen, i.e. one that is displayed first. Swipe left / right to go to another user screen (if more user screens were added by the installer). Information on which user screen is currently displayed is represented graphically on the bottom of the screen.
The user screen includes:
- status bar (see p. 7),
- widgets used to operate the alarm system, indicate the alarm system status, etc. (see “Widgets” p. 7).
To run a function with a widget, you may be required to enter a code. If this is the case, the keypad will be displayed (see p. 8). When you enter the code, the function will be run and you will be logged in. If you are already logged in, you will not be required to enter your code again when trying to run a function with a widget.
The following widgets are available on the user home screen in the keypad with factory default settings.
Consult the installer about which additional widgets may help you to operate
the alarm
system or control the home automation devices connected to the control panel.
Only the installer can create new user screens, add widgets to the screen,
etc.
The installer can configure the keypad so that the access to the user screen
is code protected
(a keypad will open before the screen is displayed).
Two different background pictures may be applied to user screens.
5. Additional screens
Additional screens differ from the user screens only in that each of them can
have a different
background picture. For this reason, the additional screens may be used to
display site plans.
If pictures other than the ones offered by SATEL are to be displayed, the
installer must save
them on a memory card and install the card in the keypad.
To display an additional screen, tap a link widget.
6. Status bar
The status bar is displayed on the top of the user screen and the additional
screen.
It includes:
- screen title (optionally, if added by the installer),
- time,
- the icon. If you are not logged in, tap the icon to log in (keypad will open – see p. 8).
If you are logged in, tap the icon to log out or go to the user menu.
7. Widgets
The following widgets may be displayed on the screen.
Text – the widget displays any text that was added by the installer or
system element name.
Partition status – the widget displays the partition status represented
by icons.
Zone status – the widget displays the zone status represented by either:
– icons selected by SATEL (indicator) – different statuses are displayed,
– text messages (text) – messages inform only about normal and violated
states,
– icons selected by the installer (icon) – only normal and violated states are
displayed.
Output status – the widget displays the output status represented by
either:
– icons selected by SATEL (indicator),
– text messages (text),
– icons selected by the installer (icon).
Temperature – the widget displays the temperature. Information about the
temperature is sourced from an ABAX 2 / ABAX wireless detector. The widget is
not available in the VERSA system.
Date/time – the widget displays the date and time in the format specified
by the installer.
Switch – the icon for the widget is selected by the installer. Tap the
widget to enable / disable an output.
Rectangle – the widget displays a rectangle that can be translucent and
have different colors. As an additional graphic element it may be used e.g. to
highlight a part of the screen.
Macro – the icon for the widget is selected by the installer. Tap the
widget to run a macro command. The macro command is a sequence of actions to
be performed by the control panel. Macro commands are created by the
installer.
8. On-screen keypad
The on-screen keypad is displayed when it is required to enter a code e.g. to access the user menu. You may be required to enter the code to access the user screen or the additional screen or to run a function with a widget.
9. User menu
Swipe up on the user screen / additional screen to go to the user menu. Since the access to the user menu is code-protected, the keypad will open first. Enter the code. The menu will open immediately if you have already logged in on the user screen.
9.1 User menu home screen
9.1.1 INTEGRA system
The following functions are available on the user menu home screen.
9.1.2 VERSA system
The following functions are available on the user menu home screen.
9.2 QWERTY keyboard
The QWERTY keyboard is used to enter text. It is displayed e.g. when you
search for items
on certain screens.
The text entered is displayed in the field above the keys.
In addition to the typing keys, the following special keys are available.
9.3 Terminal
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>