MODERN FORMS F-RCBT-WT Smart Fans Instruction Manual
- June 5, 2024
- MODERN FORMS
Table of Contents
MODERN FORMS F-RCBT-WT Smart Fans
Package Contents
Pairing
NOTE:
Pairing must be completed within three (3) minutes of turning the power ON to
the fan receiever.
To pair your remote control:
- Power cycle your fan by removing power from the circuit breaker for 10 seconds and then re-enable power.
- Press and hold and buttons on the remote control for 4-5 seconds.
- The LED will blink green.
- The green LED along with audible beeps will indicate that the pairing is successful.
- Test remote control using the steps in section 2.
NOTE: A maximum of 10 remote controls or wall controls can be used with a fan.
Remote Control Operation
Remote Control Button Functions
button: Turns the light ON or OFF. Press or hold to increase the light level.
Press or hold to decrease the light level. button: Turns the fan ON or OFF.
Press or hold the button to increase fan speed. Press or hold the button to
decrease fan speed.
NOTE:
Your fan features 6 speeds. An audible tone will indicate when the speed is
increased or decreased. When the fan has reached the minimum/maximum speed
level the fan will beep twice.
button: Switch between Summer and Winter Mode.
SUMMER MODE (Counter-Clockwise):
A downward airflow creates a cooling effect (FIG. 3). This allows you to set
your air conditioner on a warmer setting without affecting your comfort.
WINTER MODE (Clockwise):
An upward airflow moves warm air off the ceiling area and re-distributes the
warm air that hovers around the ceiling to the living space. This should allow
for savings on heating costs (FIG. 4).
NOTE : On your fan, press the button while the fan is running
Breeze Mode
- Breeze Mode mimics the natural ebb and flow of winds in nature by varying the fan speed. NOTE: Breeze Mode always rotates your fan in the Summer (CCW) direction
- To start Breeze Mode, press and for 4 seconds. The LED will blink green and the fan will beep.
- To exit Breeze Mode and return to standard fan mode, press and for 4 seconds. The led will blink green and the fan will beep. Your fan will return to the direction and speed it was set to prior to entering Breeze Mode.
Unpairing
NOTE: Unpairing must be completed within 3 minutes of turning the power on to the fan receiver.
- When you re-engage power to the fans you want to unpair, press and hold the and buttons for 4 seconds.
- The LED will blink green, and the receiver will beep to indicate that unpairing is successful.
Fan Wi-Fi Reset
NOTE: This function only resets the Wi-Fi settings.
- Press and hold the buttons for 10 sec.
- The LED will blink green and the receiver will beep to indicate that Wi-Fi reset is successful.
- After the Wi-Fi resets, the fan will broadcast its factory set network name beginning with “ModernFormsFan.”
NOTE:
Changes to your Wi-Fi network settings (SSID or Security Passphrase) will
prevent your fan from connecting to the cloud. You can re-establish
connectivity by performing a Wi-Fi Reset and using the Modern Forms app to
reconfigure the fan to connect to the network with the new settings.
Factory Reset
- Press and hold the , and buttons for 10 seconds.
- The LED will blink green and the receiver will beep to indicate that the factory reset is successful.
NOTE:
This will remove remote control(s), wall control(s) “The bluetooth ® word mark
and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use
of such marks by Wangs Alliance Corporation is under license. Other trademarks
and trade names are those of their respective owners.”
Replacing the Batteries
- Step 1: Open the back of the remote with a flat screw driver.
- Step 2: Remove the back of the remote and put it aside.
- Step 3: Remove the old batteries from the remote.
- Step 4: Insert your new to new CR2032 batteries into the remote. Step 5: Push in the back of the remote – making sure it locks into place.
Using Power Switch
This process can be used when it is inconvenient to use one of the other processes.
NOTE: You must use a switch that cuts power to the fan receiver for this process to work. This will reset all fans connected to the switch being used.
- Turn off power at power switch for 3 seconds.
- Turn on power for 6 seconds. Turn off power.
- Turn on power. In approximately 6 seconds the receiver will beep. When the receiver beeps turn off power.
Repeat step 3 four additional times. On the fourth repetition the fan will beep three times indicating the fan has performed a factory reset.
NOTE : This will remove remote control(s), wall control(s) and Modern Forms app connections.
Rules and Regulations
CAUTION:
The user is cautioned that changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
Note:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
The cells shall be disposed of properly, including keeping them away from
children and even used cells may cause injury
FCC Supplier’s Declaration of Conformity
Brand name: Modern Forms Model number: F-RCBT-WT This device complies with
part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may
cause undesired operation.
WAC LIGHTING CO.
44 Harbor Park Drive, Port Washington, NY 11050 Tel:
1-866-810-6615
WARNING:
Chemical Burn Hazard. Keep batteries away from children. This product contains
a lithium button/coin cell battery. If a new or used lithium button/coin cell
battery is swallowed or enters the body, it can cause severe internal burns
and can lead to death in as little as 2 hours. Always completely secure the
battery compartment. If the battery compartment does not close securely, stop
using the product, remove the batteries, and keep it away from children. If
you think batteries might have been swallowed or placed inside any part of the
body, seek immediate medical attention.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>