MODERN FORMS PD-92950 Stormy 929 LED Pendant Instruction Manual
- June 9, 2024
- MODERN FORMS
Table of Contents
MODERN FORMS PD-92950 Stormy 929 LED Pendant
Important Safety Instructions
CAUTION: To prevent electrical shock, ensure electricity has been turned off at the circuit breaker before beginning.
- Read all instructions before installing.
- System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
- When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
- Retain installation instructions for future maintenance reference.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or accessories designated for use by dweLED. Substitution of parts or accessories not designated for use with this product by dweLED could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any parts are damaged or missing.
MAINTENANCE NOTE: Coastal conditions may cause mineral and residue build- up on the fixture. We recommend that customers in coastal areas clean all external surfaces of the fixture once every two weeks with a wet cloth
HARDWARE
Wire Connector Qty: 5pcs+1Extra
| Mounting Screw Qty:1 extra| Plastic Anchor
Qty: 2pcs+1 extra|
Wood Screw
Qty: 2pcs+1 extra
---|---|---|---
PREPARATION
-
Shut off the power at the circuit breaker and remove existing fixture, including the crossbar.
-
Carefully unpack your new fixture and lay out all the parts on a clear .area. Be careful not to lose any small parts necessary for installation.
MOUNTING THEFIXTIJRE (Fig. 1)
-
Remove the mounting screw (8) from the fixture.
-
Drill holes in the wall aligned with the key holes located in the mounting back plate, insert the plastic anchor (0 ).
-
Secure back plate to the junction box using standard junction box screws that comes with the junction box. Fasten the back plate to the wall with the plastic anchors using the wood screws(Q provided.
Note: the side of the mounting plate marked “GNO• must face out. -
Choose the u,mp body assembly, Short metal tube 8, Rods and Lamp canopy. Thread the fixture wire through Short metal tube B, Rods and lamp canopy, rotating them. Make sure all are tightened.
CONNECTING THE WIRES (Fig. 2)
-
Cut the extra wire. Connect the driver input wires with junction box wires as shown in Fig.4, making sure that all wire connectors (A) are secured. If your outlet box has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
-
Hook the safety cords to the back plate as shown in Fig. 2.
-
Assembly the Short metal tube A on the fixture.
-
Assembly the Long metal tube and the etched acrylic on the fixture.
COMPLETING THE INSTALLATION
-
Secure the fixture to the mounting back plate using the mounting screws (8).
-
For slope ceiling application, rotate swivel at the top of the stem to ensure luminaries are aiming down (Fig.3).
Note: The fixture exceeds 20lbs, and must be installed using an outlet box U.L. approved for up to 100 lbs.
NOTE: OIMMING WIRING INFORMATION (Fig. S) -
To utilize ELV or TRAIC dimming: use black (hot), white (neutral) and bare copper ground wires (ground).
-
To utilize 0-1 OV dimming: use purple (dim+), pink or gray (dim-), b lack (hot), white (neutral) and bare copper ground wires (ground).
Customer Support
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>