Q-BEAM Brightsmith Max 14 LED Aluminum Flashlight with Lanyard Instruction Manual
- June 5, 2024
- Q-BEAM
Table of Contents
Brightsmith Max 14 LED Aluminum Flashlight with Lanyard
READ THE MANUAL FULLY BEFORE USING
BEFORE FIRST USE: Open and remove the battery sticker to allow batteries
to operate.
BATTERY REPLACEMENT: Install batteries by first unscrewing tail cap.
Remove battery compartment. Insert 3 AAA batteries into the battery
compartment; two with positive (+) ends toward head of flashlight, one with
negative (-) ends toward the head of flashlight (Fig. 1). Re-insert battery
compartment into flashlight with positive (+) end toward flashlight head.
Make sure spring is in place in the tail cap. Replace the tail cap by screwing
in securely. Use alkaline batteries for maximum brightness and life.
NOTE: Do not mix old and new batteries. Do not mix alkaline, standard
(carbon-zinc),or rechargeable (nickely cadmium) batteries.
PUSH-BUTTON SWITCH: Simply push the button switch to activate lighting
modes: High, Low, Strobe, Off.
BULB REPLACEMENT: LEDs (Light Emitting Diodes) never need replacement.
WARNINGS & CARE INSTRUCTIONS
Warnings:
- Use only as directed
- To prevent damage to eyesight, never look into light when light is on.
- DO NOT submerge light in water. Water-resistant in normal rain.
- DO NOT allow children to handle or operate.
- DO NOT use this product for other than its intended use.
- DO NOT install in gas tight enclosures.
- DO NOT attempt to charge or operate this light if cord, plug, battery, bulb, or any part of light is damaged or corroded.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Product Specifications
- 14 White LEDs
- 3 Light Modes: High, Low, & Strobe
- 3 AAA alkaline batteries, included
- Lumens – 78
- Beam – 35 meters
- Run Time – 4 hours
VIATEK® 1-YEAR LIMITED WARRANTY
Viatek® warrants this product to be free of manufacturing defects. Should any
such defect develop or become evident within one year from the date of
purchase, Viatek® will replace the entire product or, at its option, repair or
replace the defective part(s) without charge.Contact Viatek® customer service
at 888.784.2835 or at cs@viatek.com to determine whether it is necessary to
return the unit. To return, securely pack the entire unit. Be sure carton
clearly identifies sender by name and address. Attach a letter or card
describing defect and the original sales receipt. Mail prepaid to Viatek
Consumer Products Group, Inc. 6011 Century Oaks Dr. Chattanooga, TN 37416.
This warranty is void if damage or malfunction is due to abuse or failure to
operate product in accordance with instructions and on recommended electrical
current. This warranty gives you specific legal rights and you may also have
other rights which vary from state to state. If you have any questions, or
would like to learn more about Viatek®, please contact us at 888.784.2835 or
at cs@viatek.com.
Register your product online at viatekproducts.com/register-your-product-warranty
Customer Service / Le service a la clientele / Servicio al Consumidor
888.784.2835 (+1.423.402.9010)
DO NOT DISPOSE OF BATTERIES IN FIRE. ALWAYS DISPOSE OF BATTERIES PER LOCAL & FEDERAL GUIDELINES.
For questions, assistance, or replacement parts, do not return to your retailer. Contact Viatek® customer service below. For refunds on items not purchased from Viatek® directly, please contact your retailer.
VIATEK CONSUMER PRODUCTS GROUP, INC. All specifications are subject to change without notice. All rights reserved. Viatek Consumer Products Group, Inc. 6011 Century Oaks Dr. Chattanooga, TN 37416
References
- Viatek Consumer Products - Store – Viatek Consumer Products Group, Inc
- Register Your Product – Viatek Consumer Products Group, Inc
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>