zoOZ S2 Stick ZST10 700 Series Z-Wave Plus Static USB Controller User Manual
- June 5, 2024
- ZOOZ
Table of Contents
USER MANUAL
S2 STICK ZST10 700 SERIES
FEATURES
- Z-Wave Plus Static USB Controller
- The latest S2 security protocol for a truly private network
- Works with SmartStart Z-Wave devices
- NEW 700 chip for better performance than ever
- Extended range up to 2500 feet in open space
- Faster, more secure, and lower power than the 500 series
- Use it with the home automation soare of your the choice to make a DIY Z-Wave hub
- No drivers needed: works out of the box on Windows, Linux, and MAC OS
SPECIFICATIONS
- Model Number: ZST10 700
- Z-Wave Frequency: 908.42 MHz
- Power: 4.75-5.25 VDC
- SDK: 7.13
- Range: Up to 400 feet indoors
- Operating Temperature: 14-104° F
- Installation and Use: Indoor only
- Dimensions: 3.5” x 1” x 0.4”
SET-UP
Use this S2 700 Z-Wave USB Stick as a Z-Wave radio for your DIY smart home system. Simply connect it to a USB port on your PC, laptop, or Raspberry Pi and match it with home automation soare (host soare) of your choice to enjoy a fully secure, private Z-Wave Plus mesh network.
Questions? ask@getzooz.com
WINDOWS SET-UP
Windows 2000, XP, Vista, 7, 8 (32 / 64 bit)
The device will display in Device Manager under Ports.
You can access it through the Windows CreateFile API using “//.//COMxxx” where
xxx stands for the COM port number assigned by Windows.
UZB.INF and UZB.CAT is listed in the Z-Wave SDK which uses the standard usbser.sys or usbser64.sys Windows driver.
LINUX SET-UP
Linux
The device will display as “/dev/ttyUSB0”, you can discover it with the “does
| grep tty” command.
MAC OS SET-UP
MAC OS
The device will display as “/dev/cu.USB modem” under Apple: System
preferences: Network.
SerialAPI Mode:
Once the S2 stick is plugged into the USB port of the host computer, it
automatically enrolls in the SerialAPI mode and remains active (awake), always
listening for commands sent from the host soware and relaying them to the
Z-Wave devices in the network. It acts as a Z-Wave signal adapter for your
smart home system, translating any Z-Wave reports and notifications sent by
devices in your network to your smart home interface.
To get a full list of supported SerialAPI functions, go to support.getzooz.com and search for S2 Stick SerialAPI functions.
S2 STICK AS SECONDARY CONTROLLER
You can use the S2 stick as a secondary controller with your existing Z-Wave
system if it accepts additional controllers. To enroll the S2 stick in your
current system, send the inclusion command and put the S2 stick into learning
mode, using the SerialAPI mode.
FACTORY RESET
The S2 stick can only be reset by the host soare while it’s in SerialAPI mode.
The device is reset once an appropriate command from the host soare is sent to
reset the Z-Wave network.
There is no way to manually reset the S2 stick if it’s not controlled by the
host soare.
WARNING
- This product should be installed indoors upon completion of any building renovations.
- Do not install the S2 Stick in a place with direct sun exposure, high temperature, or humidity.
- Keep away from chemicals, water, and dust.
- Ensure the device is never close to any heat source or open flame to prevent fire.
- Ensure the device is connected to an electric power source that does not exceed the maximum load power.
- No part of the device may be replaced or repaired by the user.
This product can be included and operated in any ZWave network with other Z-Wave certified devices from other manufacturers and/or other applications. All nonbattery-operated nodes within the network will act as repeaters regardless of vendor to increase the reliability of the network. This product features the latest Security 2 (S2) framework to remove smart home network hacking risks. This device is equipped with a unique authentication code for trusted wireless communication.
WARRANTY
This product is covered under a 5-year limited warranty once registered. To
read the full warranty policy or file a warranty claim, please go to:
www.getzooz.com/warranty
FCC NOTE
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. STORE INDOORS WHEN NOT IN USE. SUITABLE FOR DRY LOCATIONS ONLY. DO NOT IMMERSE IN WATER. NOT FOR USE WHERE DIRECTLY EXPOSED TO WATER.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions:
- This device may not cause harmful interference,
- This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in any given installation.
If this equipment causes harmful interference to radio or television reception, the user may try to correct the interference by taking one or more of the following measures:
– Reorient or relocate receiving antenna
– Increase the separation between equipment and receiver
– Connect the equipment into a separate outlet or circuit from the receiver
– Consult the dealer or an experienced radio/TV technician for additional
assistance
All brand names displayed are trademarks of their respective holders.
© Zooz 2022
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>