VANTRUE VP05 Dash Cam Hardwire Kit User Manual
- May 15, 2024
- VANTRUE
Table of Contents
VANTRUE VP05 Dash Cam Hardwire Kit
Specifications
- Name: Dash Cam Hardwire Kit (Model NO.: VP05)
- Connector: Hardwire Kit
- Input Voltage: 12.4V – 24.4V
- Output Voltage: 12.0V – 11.6V Output: DC 5V 2500mA
- Output Current: 24.0V – 23.6V
- Working Temperature: N/A
- Cable Length: N/A
- Low Voltage Protection: Yes
- Switch Button Instruction: Voltage protection regulation for 12V and 24V vehicles
Product View
- A. Red Wire to Fuse Box
- B. Black Wire to the Ground
- C. Yellow Wire to ACC
- Four types of Fuses Adapters (ATO, Mini, ACN, Micro2)(2 sets)
- E. Type C USB Dash Cam Hardwire Kit
- F. Hardwire Kit Switch
Installation
- Read the manual before installation.
- Turn off the car and unplug the key before installation to avoid short circuits.
- Find the correct fuse slot for your hardwire kit, such as the 12V-30V rated power fuse and ACC fuse.
- Refer to your vehicle manual or consult a professional for specific fuse locations and types.
- Seek professional help for installation to prevent errors.
Caution
Ensure proper installation to avoid damage or malfunction. Follow safety precautions during installation.
Warranty & Support
Contact customer service for warranty-related queries or support needs.
FAQ
Q: Can I install the hardwire kit without professional help?
- A: While it is possible, we recommend seeking professional assistance to ensure correct installation and avoid errors.
Q: What should I do if the dash cam does not power on after installation?
- A: Check the connections and ensure all steps were followed correctly during installation. If issues persist, contact customer support for assistance.
Product View
- A. Red Wire to Fuse Box
- B. Black Wire to the Ground
- C. Yellow Wire to ACC
- D. Four Types of Fuses Adapters (ATO, Mini, ACN, Micro2)(2 sets)
- E. Type C USB Dash Cam Hardwire Kit
- F. Hardwire Kit Switch
Specifications
Switch Button Instruction
- 12V vehicle: With the hardwire kit switch turned from left to right, protection voltage will be regulated from 12.4V→12V→11.6V.
- （12V vehicle voltage protection regulation)
- 24V vehicle: With the hardwire kit switch turned from left to right, protection voltage will be regulated from 24.4V→24V→23.6V.
- （24V vehicle voltage protection regulation)
- Every time the voltage switch button, the display screen will first display the present set protection voltage, followed by the present voltage of the car battery in 2 seconds.
- When the voltage of the car battery reaches the present set protection voltage, it will automatically cut off in five minutes and stop the power supply for the dash cam.
- Notice: The error of displaying voltage is ± 0.2V, which will not affect the voltage protection function of the Hardwire Kit.
Installation
- Please read this manual before installation. When installing and wiring, please turn off the car and unplug the key to avoid a short circuit during operation.
Step 1, Find the correct fuse slot for your hardwire kit:
- 12V-30V rated power fuse
- ACC fuse
- The location and layout of the car fuse box and the type of fuse used may vary from vehicle to vehicle.
- Please refer to your vehicle manual and consult the original vehicle manufacturer or professional auto parts installer for details.
- We recommend that you ask for professional help to install it to avoid installation errors.
The diagram of the simplified fuse box is below:
- According to the instructions of the fuse box, test the fuse panel to find the location of the ACC fuse and 12V-30V rated power to fuse with a circuit tester or multimeter.
- Then remove the original fuse and insert it into the fuse box.
Step 2, Connect to the car fuse box
- Crimp the red wire, and yellow wire onto the Add-A-Fuse.
- Please identify the rated power fuse on the fuse panel, such as the fuses for appliances and reading lights. The power-rated fuse will remain energized when the ignition is off. Once identified, insert the red wire to the 12V-30V rated power fuse.
- Insert the yellow wire into the Add-A-Fuse ACC fuse.
- Note: The location and layout of the car fuse box and the type of fuse used may vary from vehicle to vehicle. Please refer to your vehicle manual for details.
- Note: The location and layout of the car fuse box and the type of fuse used may vary from vehicle to vehicle. Please refer to your vehicle manual for details.
- Fix the black wire(GND)under a metal bolt or screw in your vehicle.
Step 3, Test your installation according to the below steps
- Insert the TYPE-C end into the dash cam, start the ignition, waiting for the dash cam to start.
- Note: If the dash cam doesn’t turn on after startup, please check whether the cable is well connected. Then you can contact VANTRUE service staff for help.
- After the dash cam starts, turn off the car and unplug the key to check if the dash cam is turned off or goes into parking mode.
- Note: Some vehicles require turning off the engine and opening the driver’s door to trigger the ACC power-off signal, and a few vehicles only trigger the ACC power-off signal after a while after turning off and locking the vehicle.
- These two types of vehicles require checking whether the dash cam is turned off or enters parking mode after the AC power is turned off.
- After confirming that the dash cam is off or in the parking mode, restart the car to check whether the dash cam can start recording normally.
- If all the above steps pass the test, it indicates that the normal circuit and ACC signal test passed
Step 4, Route the power cable
- Route Hardwire Kit Type C USB cable Carefully route the power cable along the A-pillar and the windscreen and tuck it under the trim.
- Route fuse box wires
- Tie up the wires and put them in the fuse box. Please note that the Hardwire Kit switch button should be put in which is easily adjustable, not in the fuse box.
Caution
- Before using the product, please read all precautions and operation instructions to ensure use it correctly and safely.
- Some cars are unable to obtain ACC signal changes during ignition and shutdown, and these cars cannot transmit ACC signals to the dash cam during parking monitoring, which may result in some functions not being able to work properly.
- Before installation, please check the product labels to differentiate red wire, black ground wire, and yellow ACC wire.
- Connecting the wrong wire, reverse wiring, or missing wires can result in abnormal product functionality.
- Please stay away from high temperatures and humid environments to avoid product function caused by abnormal environments when using the product.
- Once product damage and functional failure are found, please do not continue to use the product to avoid causing damage to the vehicle power supply, vehicle battery, and dash camera.
- Please use the product within the scope permitted by the law.
Warranty & Support
- The Vantrue dash cam hardwire kit comes with a full 12-month warranty. If you have any questions regarding your product, please do not hesitate to contact the customer service staff of your purchase channel, or contact us at support@vantrue.net .
- Queries are typically answered within 12-24 hours. VANTRUE is firmly committed to improving our products, services, and user experience.
- If you have any thoughts on how we can do even better, we welcome your constructive feedback and suggestions. Connect with us today at support@vantrue.net
- Thank You for choosing Vantrue!
Hey, find us here:
Documents / Resources
|
VANTRUE VP05 Dash Cam Hardwire
Kit
[pdf] User Manual
VP05 Dash Cam Hardwire Kit, VP05, Dash Cam Hardwire Kit, Cam Hardwire Kit,
Hardwire Kit, Kit
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>