VANTRUE VP03 Dash Cam Hardwire Kit User Guide
- June 13, 2024
- VANTRUE
Table of Contents
VP03 Dash Cam Hardwire Kit
User Guide
VP03 Dash Cam
Hardwire Kit User Guide
VP03 Dash Cam Hardwire Kit
Hey, find us here:
|
---|---
www.vantrue.net/contact|
www.vantrue.net/contact
Product View
A.
Red Wire to Fuse Box
B. Black Wire to the Ground
C. Yellow Wire to ACC
D. Four Types of Fuses Adapters(ATO, MINI, LP MINI, MICRO 2)x2
E. VP03 Type C USB Dash Cam Hardwire Kit
F. Hardwire Kit Switch
Specifications
| Name | Description |
|---|---|
| Connector | Type C USB |
| Input Voltage | DC 12V-24V |
| Output Voltage | 5V |
| Output Current | 2A |
| Working Temperature | -22°F to 167°F |
| Cable Length | 3.5m |
| Low Voltage Protection | 12V vehicle: 11.6V-12V |
24V vehicle: 23.2V-24V
Switch Button Instruction
-
Automatically cut off when voltage below11.6v or 23.2v with switch button turning right.
-
Automatically cut off when voltage below 12V or 24V with switch button turning left.
Installation
Please read this manual before installation.
Step 1, Find the correct fuse slot for your hardwire kit:
- 12V-30V rated power fuse
- ACC fuse
The location and layout of the car fuse box and the type of fuse used may vary
from vehicle to vehicle. Please refer to your vehicle manual and consult the
original vehicle manufacturer or professional auto parts installer for
details. We recommend that you ask professional help to install to avoid
installation errors.
| NO. | Amp. | Circuits Protected |
|---|---|---|
| 1 | 7.5A | Power Window |
| 2 | 15A | Fuel Pump |
| 3 | 10A | Alternator |
| 4 | 7.5A | ABS/VSA Unit |
| 5 | 15A | Injection |
| 6 | 20A | Front Fog Lights |
| 7 | — | Not Used |
| 8 | — | Not Used |
| 9 | 7.5A | ODS |
| 10 | 7.5A | METER |
| 11 | 10A | SRS |
| 12 | 10A | Right Headlight High Beam |
| 13 | 10A | Left Headlight High Beam |
| 14 | 7.5A | Small Light (Interior) |
| 15 | 7.5A | Small Light (Exterior) |
| 16 | 10A | Right Headlight Low Beam |
| 17 | 10A | Left Headlight Low Beam |
| 18 | 20A | Headlight High Beam Main |
| 19 | 15A | Small Lights (Main) |
| 20 | — | Not Used |
| 21 | 20A | Headlight Low Beam Main |
| 22 | — | Not Used |
| 23 | — | Not Used |
| 24 | — | Not Used |
| 25 | 20A | Door Lock |
| 26 | 20A | Driver’s Power Window |
| 27 | 20A | HAC Option |
| 28 | — | Not Used |
| 29 | 15A | ACC |
| 30 | 20A | Front Passenger’s Power Window |
| 31 | — | Not Used |
| 32 | 20A | Rear Right Power Window |
| 33 | 20A | Rear Left Power Window |
| 34 | — | Not Used |
| 35 | 7.5A | ACC Radio |
| 36 | 10A | HAC |
| 37 | 7.5A | Daytime Running Light |
| 38 | 30A | Front Wiper |
The fuse control box will contain many different fuses, including cigarette
lighter, interior lights, car stereos, etc. Please refer to your owner’s
manual to find the fuse box, then test if a fuse is ignition switched or
always on with a circuit tester or multimeter.
Step 2, Connect to car fuse box
-
Crimp the red wire onto the Add-A-Fuse.
-
Please identify the rated power fuse on the fuse panel, such as the fuses for appliances and reading lights. The power rated fuse will remain energized when the ignition is off. Once identified, connect the red wire to the 12V-30V rated power fuse.
-
Connect the yellow cable to ACC fuse.
Note: If your ACC fuse slot does not fit the ACC fuse socket that comes with the hardwire kit, you can cut off the fuse socket that comes with it and wrap the yellow ACC wire around your car’s ACC fuse socket, then insert it into the fuse box.
-
Fix the black wire(GND)under a metal bolt or screw in your vehicle.
Step 3, Test your installation according to below steps
- Insert the TYPE-C end into the dash cam, start the ignition, waiting for the dash cam to start.
- After the dash cam starts, turn off the car and unplug the key to check if the dash cam is turned off or goes into parking mode.
- After confirming that the dash cam is off or in the parking mode, restart the car to check whether the dash cam can start recording normally.
If all the above steps pass the test, it indicates that the normal circuit and
ACC signal test passed.
Step 4, Route the power cable
Carefully route the power cable around the windscreen and tuck it under the
trim. 
Warranty & Support
The Vantrue dash cam hardwire kit comes with a full 12 months warranty. If you
have any questions regarding your product, please do not hesitate to contact
the customer service staff of your purchase channel, or contact us at
support@vantrue.net. Queries are typically
answered within 12-24 hours.
VANTRUE is firmly committed to always improving our products, services, and
user experience. If you have any thoughts on how we can do even better, we
welcome your constructive feedback and suggestions.
Connect with us today at support@vantrue.net
Thank You for choosing Vantrue!
Made in China
http://www.vantrue.net
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>