ADA INSTRUMENTS Marker 70 Laser Receiver User Manual
- June 5, 2024
- ADA INSTRUMENTS
Table of Contents
ADA INSTRUMENTS Marker 70 Laser Receiver
OVERVIEW
FEATURES:
- The screw of the battery compartment cover
- Battery compartment cover
- On/Off button
- Loudspeaker
- Display
- LED indicator for the direction «down»
- LED center indicator
- Detection sensor
- LED indicator for the direction «up»
- Frequency adjustment button
- Sound button
- Place for mount installation
- LED indicators of detection
- Magnets
- Laser target
- Mount
DISPLAY
- Power indicator
- Indicator for the direction «up»
- Middle mark
- Indicator for the direction «down»
- Measurement accuracy indicator
- Sound alarm indicator
SPECIFICATIONS
- Working range may be reduced due to unfavorable environmental conditions (e.g. direct sunlight). The receiver can react to nearby pulsating light (LED lamps, monitors).
- Depends on the distance between the receiver and line laser.
INSTALLATION/BATTERY REPLACEMENT
Unscrew the screw from the battery compartment cover. Open the battery
compartment cover. Insert 2 batteries, type AAA/1,5V. Observe the polarity.
Close the cover. Fasten the screw.
Note! Remove the batteries from the receiver, if you are not going to work
with it for a long time. Long-term storage may cause corrosion and self-
discharge of batteries.
MOUNT FOR THE RECEIVER
The receiver can be securely fixed with the help of the amount (16). If
necessary, the receiver can be attached to steel parts using magnets (14).
ADJUSTMENT OF THE RECEIVER
The receiver must be adjusted to the frequency of the line laser before use.
All settings are saved after switching off.
Choose one of the pre-installed frequencies for the setting. Switch on the
receiver to enter this mode. Press and hold the sound button (11) for more
than 20 sec. All arrows (18 and 20), and the middle mark (19) will light up on
the display. Blinking sector shows the selected frequency variant. Press the
frequency adjustment button (10) to change the frequency variant. To save your
choice, press and hold the button (11) for more than 5 sec. If the receiver
doesn’t react on the laser beam, choose another frequency variant (the
distance to check is no less than 5 m). Sector, indicating the selected
frequency variant, will blink 3 times when switching on the receiver.
USAGE
Use the receiver mode in bright light, when the laser beam is poorly visible.
The minimum distance to use a receiver is 5 m. Switch on the detector mode on
the line laser. Switch on the receiver by pressing the On/Off button. Switch
on or switch off the backlight by short pressing the On/Off button. Press and
hold the On/Off button for more than 3 sec to switch Off the receiver. Select
the measurement frequency by pressing the button (10). The icon of the
selected mode for scanning beam will appear on the display: ±1 mm (one bar),
±2 mm (2 bars). Choose the sound (2 variants) or mute mode by pressing the
sound button (11). When the sound mode is selected, the loudspeaker icon is
shown on the display. Place the receiver sensor towards the laser beam and
move it up and down (horizontal beam scanning) or right and left (vertical
beam scanning), until arrows will appear on the display (LED arrows will light
up). There will be a sound alarm when the arrows will appear on the display
(if the sound is ON). Move the receiver towards the arrows. When the laser
beam is in the middle of the receiver, a continuous beep sounds and the
display shows the middle mark (LED center indicator lights up). Marks on the
sides of the receiver correspond to the middle position of the laser beam on
the receiver. Use them to mark the surface to be marked. When marking, the
receiver must be strictly in a vertical position (horizontal beam) or strictly
in a horizontal position (vertical beam). Otherwise, the mark will be shifted.
Laser target (15) is on the backside of the receiver. It is used as a template
without switching on the receiver.
CARE AND CLEANING
- Handle the receiver with care.
- Never immerse it into the water or other liquids.
- Clean with a dry soft cloth only after any use. Do not use any cleaning agents or solvents.
WARRANTY
This product is warranted by the manufacturer to the original purchaser to be
free from defects in material and workmanship under normal use for a period of
two (2) years from the date of purchase. During the warranty period, and upon
proof of purchase, the product will be repaired or replaced (with the same or
similar model at the manufacturer’s option), without charge for either part of
labor. In case of a defect please contact the dealer where you originally
purchased this product. The warranty will not apply to this product if it has
been misused, abused, or altered. Without limiting the foregoing, leakage of
the battery, and bending or dropping the unit are presumed to be defects
resulting from misuse or abuse.
The user of this product is expected to follow the instructions given in the operators’ manual. Although all instruments left our warehouse in perfect condition and adjustment the user is expected to carry out periodic checks of the product’s accuracy and general performance. The manufacturer, or its representatives, assumes no responsibility of the results of faulty or intentional usage or misuse including any direct, indirect, consequential damage, and loss of profits. The manufacturer, or its representatives, assumes no responsibility for consequential damage, and loss of profits by any disaster (earthquake, storm, flood …), fire, accident, or an act of a third party and/or usage in other than usual conditions.
The manufacturer, or its representatives, assumes no responsibility for any
damage, and loss of profits due to a change of data, loss of data and
interruption of business, etc., caused by using the product or an unusable
product. The manufacturer, or its representatives, assumes no responsibility
for any damage, and loss of profits caused by usage other than explained in
the users’ manual.
The manufacturer, or its representatives, assumes no responsibility for damage
caused by wrong movement or action due to connecting with other products.
WARRANTY DOESN’T EXTEND TO THE FOLLOWING CASES:
- If the standard or serial product number will be changed, erased, removed, or will be unreadable.
- Periodic maintenance, repair, or changing parts as a result of their normal runout.
- All adaptations and modifications with the purpose of improvement and expansion of the normal sphere of product application, mentioned in the service instruction, without the tentative written agreement of the expert provider.
- Service by anyone other than an authorized service center.
- Damage to products or parts caused by misuse, including, without limitation, misapplication or negligence of the terms of service instruction.
- Power supply units, chargers, accessories, wearing parts.
- Products, damaged from mishandling, faulty adjustment, maintenance with low-quality and non-standard materials, presence of any liquids and foreign objects inside the product.
- Acts of God and/or actions of third persons.
- In case of unwarranted repair till the end of the warranty period because of damages during the operation of the product, its a transportation and storing, the warranty doesn’t resume.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>