HENRAC TECH 805 Robotic Vacuum Cleaner User Manual
- June 5, 2024
- HENRAC TECH
Table of Contents
Robotic Vacuum Cleaner
Model: 805
User Manual
Thank you for purchasing the 805 Robot Vacuum Cleaner, read all instructions before using this product, and keep it properly for future reference.
Safety Instructions
To reduce the risk of injury or damage, read these safety instructions
carefully and keep them at hand when setting up, using, and maintaining this
device.
WARNING SYMBOLS USED This is the safety alert symbol. This symbol alerts
you to potential hazards that could result in property damage and/or serious
bodily harm or death.
- This device can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of this device in a safe way and understand the hazards involved.
- Children should be supervised to ensure they do not play with this device.
- Cleaning and maintenance should not be performed by children without adult supervision.
- This device is only to be used with the power supply unit provided.
- For the purposes of recharging the battery, only use the detachable power supply unit provided with this device.
- The battery must be removed from this device before this device is disposed of. To remove the battery from this device, first, remove the screws on the bottom, then remove the main PCB and unscrew the battery cover using a screwdriver. Remove the battery by disconnecting the quick connector.
- The used battery should be placed in a sealed plastic bag and disposed of safely according to local environmental regulations.
- The external flexible cable or cord of the power supply unit cannot be replaced; if the cord is damaged, the power supply shall be disposed of
- This device is for indoor use only.
- This device is not a toy. Do not sit or stand on this device. Small children and pets should be supervised when this device is operating.
- Store and operate this device in room temperature environments only.
- Clean with a cloth dampened with water only.
- Do not use this device to pick up anything that is burning or smoking.
- Do not use this device to pick up spills of bleach, paint, chemicals, or anything wet.
- Before using this device, pick up objects like clothing and lose paper. Lift up cords for blinds of curtains, and move power cords and fragile objects out of the way. If this device passes over a power cord and drags it, an object could be pulled off a table or shelf
- If the room to be cleaned has a balcony, a physical barrier should be used to prevent access to the balcony and to ensure safe operation.
- Do not place anything on top of this device.
- Be aware that this device moves around on its own. Take care when walking in the area where this device is operating to avoid stepping on it.
- Do not operate this device in areas with exposed electrical outlets on the floor.
- Do not expose the electronics of this device, its battery, or the integrated Charging Base. There are no user-serviceable parts inside.
- Do not use this device on an unfinished, unsealed, waxed, or rough floor. It may result in damage to the floor and this device. Use only on hard floor surfaces or low-pile carpet.
- This device has been designed to be used on floors without scratching them. We still recommend that you test this device on a small area of the room to be cleaned to ensure no scratches are made before the whole room.
Notice
This symbol on the device or its packaging indicates: Do not dispose of
electrical appliances as unsorted municipal waste; use separate collection
facilities. Contact your local authority for information regarding the
collection systems available. If electrical appliances are disposed of in
landfills or dumps, hazardous substances can leak into the groundwater and get
into the food chain, damaging your health and well-being. When replacing old
appliances with new ones, the retailer is legally obliged to take back your
ole appliances for disposal at least free of charge.
FCC Statement
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Product features
This product is particularly designed with superpower vacuuming possibilities;
it can be used for a variety of dust cleaning with a user-friendly experience.
Considerate designs
This Robotic Vacuum Cleaner is with easy set-up and operation procedure to let
you turn on the switch by flipping over the dustbin cover and clean the room
by simply touching the On/Off button on the middle of the cleaner, dustbin is
located at the top center of the cleaner under the cover.
Washable dustbin
The dustbin and HEPA filter can be easily removed and cleaned by running
water, simply wash the dustbin after each usage to avoid dust blowing away and
causing second-time pollution.
What’s in the Box
Product components
Robot Vacuum Cleaner Anatomy
-
Top
-
Bottom****
Dust Collector
****
Remote Control
Dust Collector
| Remote buttons | Functions |
|---|---|
| (Standby) Rest button | If the robot is under standby status, by pressing this |
button, the robot goes to rest status, if the robot is under rest status, by
pressing this button; the robot goes to standby status.
Forward button| The robot cleaner moves forward and automatically stops when
detecting obstacles.
Right-turn button| The Robot cleaner moves on the right-hand side slightly.
Left-turn button| The Robot cleaner moves on the left-hand side slightly.
Backward button| The Robot cleaner moves backward at a certain distance.
Start/stop button| Start the auto cleaning mode, and stops the robot during
the operation.
Spot cleaning button| To clean the specific cleaning zone.
Edge cleaning button| The Robot cleaner looks for the wall edge and cleans the
room along the wall.
Home charging button| The robot cleaner goes to the charging base for
charging.
Vacuum strength button| To adjust the vacuuming power during the cleaning
process.
Install 2 AAA batteries before using the remote control for the first time. Make sure the positive and negative ends are facing the correct polarity direction as marked in the battery compartment.
Using Your Robot Vacuum Cleaner
Various Cleaning modes
- Auto cleaning mode The Robot will clean a room automatically and adjust its cleaning according to the situation.
- Spot cleaning mode The robot will spiral intensely under this cleaning mode, and the vacuuming power will be increased for a better cleaning effect with stronger cleaning power.
- Edge cleaning mode When the robot detects obstacles (wall for example), it will start cleaning the room with its two side brushes. Under edge cleaning mode, the robot will clean the surrounding areas of obstacles.
Place physical barriers in front of fireplaces and areas that may cause damage
to Robot Vacuum Cleaner if entered.
Charging options
Charge the Robot cleaner in either way below:
-
Plug the adaptor into the robot cleaner and the electrical outlet.
Note:
A. Please make sure that the power switch on the robot cleaner is turned on.
B. Please charge 12 hours for initial charging (no flashlight on the panel when fully charged).
C. Please use up the charged battery for initial cleaning.
D. After the battery is run out, please charge the battery immediately.
E. If the Robot cleaner is not to be used, please turn off the power switch from the main unit.
F. The light indicator will be flashing if the power is run out, please charge the robot cleaner timely. -
To place the charging base for automatic charging:
Place the Charging Base stably against the wall, remove obstacles 1 meter from two sides and 2 meters from forward, and place the Charging Base away from the mirror or smooth surface which might easily cause reflections. Press the Home charging button on the remote control, and let the robot charge itself from the Charging Base automatically. When the cleaning process is finished or the battery is low, the robot cleaner will go back to the Charging Base for charging automatically. Please keep the Charging Base connected with electrical power to make sure that the robot cleaner can get charged from it.
– Install the Charging Base in a location that Robot Vacuum Cleaner can easily
access. It is recommended to place the Charging Base against a wall, and on a
hard-level surface rather than on rugs or carpets.
– Always keep the Charging Base plugged in, otherwise, Robot Vacuum Cleaner
will not automatically return to it.
Start Your Robot Vacuum Cleaner
-
Start the Robot Cleaner
1.1 Make sure the switch under the top cover is turned on.
1.2 Press the start button on the robot cleaner, or press the start button on the remote control to start the robot. -
Stop the Robot Cleaner
To stop the Robot cleaner, means to change the working status of the robot cleaner into standby mode, and it can be stopped by the following method:
2.1 By pressing the start/stop button on the robot cleaner.
2.2 By pressing the start/stop button on the remote control.
The robot cleaner will go back to the working status by pressing again the start/stop button. -
Rest the Robot Cleaner
To rest the robot cleaner is to turn it to a power-saving mode, the display will not waste electrical power.
3.1 If the robot cleaner is not having any command for cleaning for 80 seconds, it will be turned to the rest status automatically.
3.2 If the rest button is pressed, the robot cleaner will be forced into rest status.
Note: if the robot cleaner is not to be used for a long time, please turn off the switch on the robot cleaner.
Cleaning & Maintenance
Clean and replace the side brush
The side brushes may become bent or damaged after being used for a period of
time. Follow the instructions below to replace them.
A. To check the side brush status to see if there is any damage or hairs that
need to be cleaned.
B. Use a cleaning tool to get rid of hairs and clean the edge with a clean
cloth.
C. Pull off the old side brushes and snap the new ones into place.
Clean the dustbin and HEPA filter
Follow the discharging process of the photos to discharge the dustbin and
clean the HEPA filters.
A. Flip over the top cover.
B. To get rid of the dustbin.
C. To discharge to HEPA filter.
D. To empty the dust.
E. To remove the pre-filter.
F. To rinse the dustbin and HPEA filter with water, Clean the pre-filter with
a cleaning brush.
G. To reassemble the HEPA filter and pre-filter. H. To place the dustbin back
into the robot cleaner.
– Install the Charging Base in a location that Robot Vacuum Cleaner can easily
access. It is recommended to place the Charging Base against a wall, and on a
hard-level surface rather than on rugs or carpets.
– Always keep the Charging Base plugged in, otherwise, Robot Vacuum Cleaner
will not automatically return to it.
Clean the Sensors and Charging Pins
To maintain the best performance, clean the floor sensors and charging pins
regularly. Item 1 to 3 is the floor sensor.
Replaceable spare parts
- Please be noted that all the listed spare parts are replaceable by a professional after-sales team or by professional distributors, please contact your local agent to get extra spare parts replaced if necessary.
Replace the battery
To maintain the best performance, check the lithium battery status regularly
and replace it when it is necessary. The right process for discharging the
battery and replacing the battery is the following:
- Remove the screw sets from the battery lid.
- Take off the battery lid.
- To get rid of the battery by pulling off the insulation cloth gently.
- To disconnect the connecting cable between the battery and the robot cleaner.
- Put a new battery inside of the battery socket.
- Reconnect the connecting cable.
- Set the insulation cloth and the cable well.
- To reset the battery lid.
- To lock the battery lid by screw sets.
– Please do not use a lithium battery that does not match the operation requirement of this robot cleaner, seek professional advice before you select the right battery.
Cleaning & Maintenance
| Product Model| 805
---|---|---
Dimension| 310x310x75mm
Weight| 2.0Kgs
Input| DC 14.8V
Battery Voltage| DC 14.8V
Power Consumption| 22w
Battery Type| 2000mAh Lithium-ion Battery
Dust Collector Capacity| 400m1
Cleaning Time| 90 Min.
Charging time| 240-360 Min.
| Input| DC 18V/ 0.5A
---|---|---
Output| DC18V/ 0.5A
| Input| DC 3V
---|---|---
Model|
| Input| AC 100-240V 50-60Hz
Output| DC 18V/ 0.5A
Documents / Resources
|
HENRAC TECH 805 Robotic Vacuum
Cleaner
[pdf] User Manual
805, Robotic Vacuum Cleaner
---|---