BASS HABIT SE1200.1DF Elite Class D Full Bridge Amplifier User Manual

: June 3, 2024
: BASS HABIT

Table of Contents

SE1200.1DF Elite Class D Full Bridge Amplifier
UNPACKING
SAFETY & WARRANTY
INSTRUCTIONS
STEP 2) SPEAKER CONNECTIONS
CONTROL PANEL
SPECIFICATIONS
TROUBLESHOOTING
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Elite
SE1200.1DF
SE2100.1DF
SE3100.1DF
SE5100.1DF
Elite Class D Full Bridge Amplifier User Manual

SE1200.1DF Elite Class D Full Bridge Amplifier

THANK YOU!
Thank you for purchasing this SPL Elite Class D full bridge amplifier from Bass Habit.
Please read this manual in order to fully understand how to get the best result from this product and ensure that the advice on how to look after the product and the safety precautions are followed. We hope you enjoy using the product as much as we enjoyed creating it.
Before mounting and installing your new amplifier, please read through the whole user manual. If you have any questions concerning your amplifier or any other Bass Habit products, contact your nearest Bass Habit dealer/distributor.

UNPACKING

INCLUDED IN THE PACKAGING

Mono amplifier
Bass level remote
Bass-level remote cable 5M
Screws 6pcs
Allen keys 2pcs
User manual
Bass Habit sticker

SAFETY & WARRANTY

DO NOT EXPOSE THIS PRODUCT TO EXCESSIVE DAMPNESS OR MOISTURE

Doing so may result in shock or damage to the product.

BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL

Failure to do so may result in electric shock or injury.

ENSURE GOOD AND CORRECT CONNECTIONS

Failure to make the correct connections may result in permanent damage to the product.

DO NOT USE ANY FUNCTIONS THAT MAY TAKE YOUR CONCENTRATION AWAY FROM DRIVING YOUR VEHICLE

Do not set up your amplifier whilst driving. Doing so may result in an accident. For prolonged interaction with the product, make sure that your vehicle is stationary and parked in a safe location.

CAUTION
Never connect any speaker lead to the car chassis. This can cause severe damage to your car’s audio setup.
Before drilling or cutting any holes, investigate the layout of your vehicle thoroughly.
Use caution when working near the fuel/hydraulic lines and electrical wiring.
Observe the correct polarity when wiring. Improper phasing may cause a loss of bass response.
Ensure that no moving parts get caught on the subwoofer or grill.
WARRANTY
All Bass Habit products carry a full warranty depending on the conditions in the country where it is sold. The warranty is valid from the date of the original receipt as proof of purchase (the warranty period differs depending on local warranty laws and policies). Contact your international Bass Habit dealer or distributor concerning the specific procedures for your country’s warranty policies.
WHAT IS NOT COVERED

Damage to the product due to improper installation.
Subsequent damage to other components.
Damage is caused by exposure to moisture, excessive heat, chemical cleaners, and/or UV radiation.
Damage through negligence, misuse, accident, or abuse. Repeated returns for the same fault may be considered abuse.
Any cost or expense related to the removal and/or abuse. Repeated returns for the same fault may be considered abuse.
Damage caused by amplifier clipping or distortion.
Items repaired or modified by any unauthorized repair facility.
Return shipping on non-defective items.
Products returned without a return authorization number.
Damage to the product due to the use of sealant.

WARNING
Bass Habit equipment is capable of sound pressure levels that can cause permanent damage to your hearing and those around you. Please use common sense when listening to your audio system and practice safe sound. Keep the volume at a level so you can still hear outside noise. Failure to do this may result in an accident. Bass Habit recommends caution when listening at a high volume. For safety and enjoyable listening, the sound should be clear without distortion.
INTERNATIONAL TECHNICAL ENQUIRIES
For international technical support please contact the dealer/distribution agent for your country.

INSTRUCTIONS

INSTALLATION EXPERIENCE
Installation of Bass Habit amplifiers may require experience with a variety of mechanical procedures including cable wiring, drilling, etc. This manual only provides general installation and operation instructions. If you have any reservations about your installation skills, please contact your local authorized Bass Habit dealer for help.
CHOOSING AMPLIFIER MOUNTING LOCATIONS
Choose a mounting location in an area where the amplifier will not be damaged, and where the amplifier is not covered up. Mount the amplifier so that it remains dry – never mount an amplifier outside the vehicle or in the engine compartment. Amplifier cooling is essential for proper amplifier operation. If the amplifier is to be installed in an enclosed space, make sure there is sufficient air circulation for the amplifier to cool itself. When mounting the amplifier under a seat, ensure that it is clear of all moving parts and does not affect the seat functionality. Make sure that the amplifier is mounted securely using nuts and bolts or the supplied mounting screws.
WARNING! DO NOT START the amplifier WITHOUT a load on the speaker output terminals.
Ignoring to do so can potentially result in a circuit failure in the start-up mode sequence and leave the amplifier stuck in protect mode (see specifications for correct impedance).
INSTALLATION PRECAUTIONS
NOTE! Proceed only if you are a qualified installer, otherwise, let your dealer do it.

Always wear protective eyewear when using tools.
Turn off all stereo and other electrical devices before you begin.
Disconnect the (-) negative lead from your vehicle’s battery.
Keep the amplifier in the package until final installation, and always rest it upwards.
Never use force when installing an amplifier.
Locate all fuel lines, brake lines, oil lines, and electrical cables when planning your installation.
Check clearances on both sides of a planned mounting surface before drilling any holes or fixing screws.
When routing cables, keep input-signal cables away from power cables and speaker wires.
When making connections, make certain all cables are secure and properly insulated.

STEP 1) POWER CONNECTIONS
The Bass Habit SPL Elite amplifiers are capable of delivering extremely high power levels and require a heavy-duty and reliable connection to the vehicle’s electrical system. To get the very best performance out of your Bass Habit SPL Elite amplifier, carefully follow the instructions below:
GROUND CONNECTION (GND):
Connect the amplifier’s Ground (GND) terminal to a solid point on the vehicle’s metal chassis, as close to the amplifiers as possible. Scrape away any paint from this location; use a star-type lock washer to secure the connection.
Ground wire recommended size:
SE1200.1DF: 4 AWG/ 20mm2
SE3100.1DF: 0 AWG/ 50mm2
SE2100.1DF: 2 AWG/ 35mm2
SE5100.1DF: 2 x 0 AWG/ 2 x 50mm2
POWER CONNECTION (+12V):
Connect a wire directly to the vehicle’s positive battery terminal, and install an appropriate fuse and holder within 30cm/12” from the battery terminal. Keep the fuse installed at the time for routing and connecting the power wire. Be sure to use grommets whenever routing wires through the firewall or other metal parts. When routing/connecting is done, installation of the fuse into the fuse holder can be finalized.
+12V wire recommended size:
SE1200.1DF: 4 AWG/ 20mm2
SE3100.1DF: 0 AWG/ 50mm2
SE2100.1DF: 2 AWG/ 35mm2
SE5100.1DF: 2 x 0 AWG/ 2 x 50mm2
REMOTE CONNECTION (REM):
Connect the amplifier’s Remote (REM) terminal to the source unit Remote turn on the lead using a minimum of 0.75mm2/18 gauge wire. If your source unit does not have a turn-on connection, connect the amplifier (REM) terminal through a power switch button which can provide a +12V signal.
Remote wire maximum accepted size for terminal:
SE1200.1DF: MAX 10 AWG/ 6mm2
SE3100.1DF: MAX 10 AWG/ 6mm2
SE2100.1DF: MAX 10 AWG/ 6mm2
SE5100.1DF: MAX 10 AWG/ 6mm2 (IN) / 10 AWG/ 6mm2 (OUT)
FIG 1: POWER CONNECTIONS BASS HABIT SE1200 1DF Elite Class D Full Bridge
Amplifier

FIG 1.5: POWER CONNECTIONS FOR SE5100.1DF BASS HABIT SE1200 1DF Elite
Class D Full Bridge Amplifier - Fig

NOTE! SE series amplifiers do not come with internal or external fusing.
Always make sure you install appropriate inline fusing on the positive power source side.
Recommended external fuse size:
SE1200.1DF: 80A-100A
SE3100.1DF: 250A
SE2100.1DF: 150A
SE5100.1DF: 2x250A

STEP 2) SPEAKER CONNECTIONS

SPEAKER CONNECTIONS (SPEAKER OUTPUT):
Speaker connections should be made using a minimum of 16 awg/1,25mm2 wire. The terminal accepts up to 8 AWG/10mm2. The minimum total allowed impedance load is 1 ohm depending on the model.
FIG 2: SPEAKER CONNECTIONS BASS HABIT SE1200 1DF Elite Class D Full
Bridge Amplifier - Fig 1

WARNING! DO NOT START the amplifier WITHOUT a load on the speaker output terminals.
Ignoring to do so can potentially result in a circuit failure in the start-up mode sequence and leave the amplifier stuck in protect mode (see specifications for correct impedance).
STEP 3) SIGNAL CONNECTIONS
SIGNAL CABLE CONNECTION (SIGNAL INPUT):
Use high-quality RCA signal cables to make sure you get the full audio experience.
FIG 3: SIGNAL CABLE CONNECTIONS BASS HABIT SE1200 1DF Elite Class D Full
Bridge Amplifier - Fig 2

CONTROL PANEL

FRONT PANEL (SEE FIG 4 ON THE NEXT PAGE)
Bass Habit SPL Elite ampliﬁers can be used for speakers and subwoofers in the range between 15Hz – 20KHz.
While listening to music, adjust the gain/crossover/subsonic/bass boost for the least perceived distortion from the speakers, allowing them to reproduce as much bass as possible.
Input level control (GAIN):
GAIN control is a seamless adjustable between 0,2V – 5V.
Tips for adjusting the GAIN control correctly:

Initially turn the GAIN control to a minimum (counterclockwise).
On the source unit, increase the volume control to the 3/4 of maximum volume.
Slowly increase the GAIN control until you hear slight distortion in the speaker/speakers and the Clipping LED on the ampliﬁer starts to ﬂash or is lit.
Then reduce the GAIN slightly until the distortion is no longer heard or the Clipping LED no longer ﬂashes or is lit.

Bass Boost control (BASS BOOST):
Bass Boost is seamlessly adjustable between 0-12 DB (35Hz – 70 Hz)
Please use the BASS BOOST knob with care, excessive use can damage your system!
LPF Crossover (LPF):
The low pass ﬁlter is seamlessly adjustable between 60Hz – 20KHz. When using a subwoofer, set the frequency cut point at 60Hz and adjust to your own preferences.
HPF Crossover (HPF):
The high pass ﬁlter is seamlessly adjustable between 15Hz–1KHz. The HPF can be used for removing the deepest bass notes from the subwoofer, to get a tighter and more rhythmical sound. For a normal setup, the HPF should be adjusted to the “15 Hz” setting.
Remote Level Control (REMOTE):
Included with the Bass Habit SPL Elite two-channel and ﬁve channel ampliﬁer is a wired subwoofer remote volume control with a clipping indicator. This allows you to adjust the level from your listening position. Install the controller at a convenient position close to the driver seat, and connect it to the REMOTE jack on the ampliﬁer. NOTE! The level control will attenuate from the lowest gain to the highest previously set on the ampliﬁer.
Power status, Clipping & Protection LED:

PWR = Power LED lights up when the ampliﬁer is turned on. Normally during the start-up sequence, the PWR, CLIP, and PRT lights will ﬂash as a self-test procedure.
CLIP = Clipping LED ﬂashing or solid. This light is an indicator of distortion in the gain structure and can possibly damage your speakers. Turn down your remote level controller or gain knob.
PRT = Protect LED light ﬂashing or solid. This light is an indicator of the protect mode status, see the troubleshooting section of the manual for more information.

Line Input:
Connect the line outputs from your source unit and connect to the Line L and R inputs.
Line Output:
Bass Habit SPL Elite class D mono ampliﬁers are equipped with full-range output that can be used to connect additional ampliﬁers.
FIG 4: FRONT PANEL BASS HABIT SE1200 1DF Elite Class D Full Bridge
Amplifier - Fig 3

1| RCA signal input/output| Connect the RCA signal wire from the audio source/head unit (Input) Connect another ampliﬁer (using an RCA cable) (Output)
---|---|---
2| RCA signal input| Connect the RCA signal wire from the audio source/head unit
3| High pass ﬁlter (HPF)| Adjust the High pass ﬁlter’s crossover point (15KHz – 1KHz)
4| Low pass ﬁlter (LPF)| Adjust the bass boost’s center frequency (35Hz – 70Hz)
5| Gain| Adjust the Low pass ﬁlter’s crossover point (60Hz – 20KHz)
6| Bass boost level (LEVEL)| Adjust the Gain level (0,2-5V)
7| Bass boost frequency (FREQ)| Adjust the bass boost level between 0-12 dB
8| Subwoofer remote volume control input| Input for the connection of the bass remote control
9| Power status, Clipping & Protection LED| Indicating the power & clipping status and activating protection mode
10| Speaker wire terminal| Connect to a speaker/subwoofer

SPECIFICATIONS

| SE1200.1DF| SE2100.1DF
---|---|---
Component| Class D full bridge amplifier| Class D full bridge amplifier
Number of channels| 1 channel (mono)| 1 channel (mono)
Power output @ 1 ohm| 1200W RMS | 2100W RMS
Power output @ 2 ohm| 800W RMS | 1450W RMS
Power output @ 4 ohm| 500W RMS | 850W RMS
Power output MAX| 2400W MAX| 4200W MAX
Input sensitivity| 0,2 – 5V| 0,2 – 5V
S/N| 100dB| 100dB
Frequency response| 15Hz – 20KHz| 15Hz – 20KHz
LPF crossover control| 60Hz – 20KHz| 60Hz – 20KHz
HPF crossover control| 15Hz – 1KHz| 15Hz – 1KHz
Operation voltage| 10.5V – 15.5V DC| 10.5V – 15.5V DC
Fuse| N/A| N/A
Recommended Fuse| 80-100A| 150A
Bass Level Remote with clipping indicator| Included| Included
Measurements| 151x209x67mm| 191x209x67mm
Cooling system| Smart thermal management system (STMS)| Smart thermal management system (STMS)
Protection system| 4-Way Protection Circuit (Thermal,
DC Offset,Voltage & Speaker short)| 4-Way Protection Circuit (Thermal,
DC Offset,Voltage & Speaker short)
Component| Class D full bridge amplifier| Class D full bridge amplifier
Number of channels| 1 channel (mono)| 1 channel (mono)
Power output @ 1 ohm| 3100W RMS | 5100W RMS
Power output @ 2 ohm| 1900W RMS | 3100W RMS
Power output @ 4 ohm| 1050W RMS | 2100W RMS
Power output MAX| 6200W MAX| 10200W MAX
Input sensitivity| 0,2 – 5V| 0,2 – 5V
S/N| 100dB| 100dB
Frequency response| 15Hz – 20KHz| 15Hz – 20KHz
LPF crossover control| 60Hz – 20KHz| 60Hz – 20KHz
HPF crossover control| 15Hz – 1KHz| 15Hz – 1KHz
Operation voltage| 10.5V – 15.5V DC| 10.5V – 15.5V DC
Fuse| N/A| N/A
Recommended Fuse| 250A| 2x250A
Bass Level Remote with clipping indicator| Included| Included
Measurements| 211x209x67mm| 291x209x67mm
Cooling system| Smart thermal management system (STMS)| Smart thermal management system (STMS)
Protection system| 4-Way Protection Circuit (Thermal, DC offset, Voltage & Speaker short)| 4-Way Protection Circuit (Thermal,
DC Offset,Voltage & Speaker short)

TROUBLESHOOTING

Symptom	Check / Control

No sound
/ No active PWR LED| • Check and measure the voltage at +12V and REM terminals (the allowed working range is 10.5-15.5V DC).
• Check and measure ground connections.
• Check the external fuse.
• Check the input signal and cables from the source unit.
• Check speaker wires and terminals.
Noise or Distorted sound
/ Low output| • Check crossover/input level/control knobs and switches.
• Check ground connections of all installed audio equipment, (source unit, DSP, etc.).
• Check speaker wires for possible short circuits.
• Check the impedance load of the speaker/speakers according to the manual.
• Check speaker connections for proper polarity.
Ampliﬁer Protection mode
(PRT)| • Check the impedance load of the speaker/speakers according to the manual.
• Check chassis ground connections.
• Check speaker wires for possible short circuits.
• Check power input voltage (allowed working range is 10.5-15.5V DC).
• Check RCA input voltage (allowed range is 0,2-5V).
• Check the RCA cable for possible short circuits.

The crossed-out wheelie bin symbol means that the product, literature, and packaging included must be taken to a separate collection at the end of their working life. Do not dispose of these products as unsorted municipal waste: dispose of them at a recycling point. For info on your nearest recycling point, check with your local waste authority.
Products marked with the RoHS symbol comply with the relevant provisions of the RoHS Directive for the European Union. In common with all Electrical and Electronic Equipment (EEE) the product should not be disposed of as household waste. Alternative arrangements may apply in other jurisdictions.
The product with the CE mark indicates that it has passed the corresponding conformity assessment procedure and the manufacturer’s declaration of conformity, and it complies with the relevant EU directives and is used as a pass for the product to be allowed to enter the European Community market. Relevant directives require industrial products to be affixed with the CE mark. Those that do not have the CE mark shall not be marketed.

Winn Scandinavia AB
Elementvägen 15, 702 27 Örebro
Sweden
www.winnscandinavia.com
Winn Scandinavia reserves for possible typos, factual or numeric errors that may have been printed on any
products, package designs, user manuals and/or other included accessories.