BASS HABIT PP70.2 G2 Play Power 2-Channel Amplifier User Manual
- June 3, 2024
- BASS HABIT
Table of Contents
BASS HABIT PP70.2 G2 Play Power 2-Channel Amplifier
THANK YOU FOR PURCHASING BASS HABIT
Thank you for purchasing this Play Power Class A/B amplifier from Bass Habit.
Please read this manual in order to fully understand how to get the best
result from this product and ensure that the advices on how to look after the
product and the safety precautions are followed. We hope you enjoy using the
product as much as we enjoyed creating it. Before mounting and installing your
new amplifier, please read through the whole user manual. If you have any
questions concerning your amplifier or any other Bass Habit products, contact
your nearest Bass Habit dealer/distributor.
UNPACKING
INCLUDED IN THE PACKAGING
- 2-channel amplifier
- Fuses · Screws 4pcs
- User manual
- Bass Habit sticker
SAFETY & WARRANTY
- DO NOT EXPOSE THIS PRODUCT TO EXCESSIVE DAMP OR MOISTURE – Doing so may result in shock or damage to the product.
- BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL – Failure to do so may result in electric shock or injury.
- ENSURE GOOD AND CORRECT CONNECTIONS – Failure to make the correct connections may result in permanent damage to the product.
- DO NOT USE ANY FUNCTIONS THAT MAY TAKE YOUR CONCENTRATION AWAY FROM DRIVING YOUR VEHICLE – Do not setup your amplifier whilst driving. Doing so may result in an accident. For prolonged interaction with the product, make sure that your vehicle is stationary and parked in a safe location.
- CAUTION Never connect any speaker lead to the car chassi. This can cause severe damage to your car audio setup. Before drilling or cutting any holes, investigate the layout of your vehicle thoroughly. Use caution when working near the fuel/hydraulic lines and electrical wiring. Observe the correct polarity when wiring. Improper phasing may cause a loss of bass response. Ensure that no moving parts get caught on the subwoofer or grill.
WARRANTY
All Bass Habit products carry a full warranty depending on the conditions
in the country where it is sold. The warranty is valid from the date of the
original receipt as proof of purchase (warranty period differs depending on
local warranty laws and policies). Contact your international Bass Habit
dealer or distributor concerning specific procedure for your country’s
warranty policies.
WHAT IS NOT COVERED
· Damage to product due to improper installation.
· Subsequent damage to other components.
· Damage caused by exposure to moisture, excessive heat, chemical cleaners
and/or UV radiation.
· Damage through negligence, missuse, accident or abuse. Repeated returns for
the same fault may be
considered as abuse.
· Any cost or expense related to the removal and/or abuse. Repeated returns
for the same fault may be
considered as abuse.
· Damage caused by amplifier clipping or distortion.
· Items repaired or modified by any unauthorised repair facility.
· Return shipping on non-defective items.
· Products returned without a return authorisation number.
· Damage to product due to use of sealant.
WARNING
Bass Habit equipment is capable of sound pressure levels that can cause
permanent damage to your hearing and those around you. Please use common sense
when listening to your audio system and practice safe sound. Keep the volume
at a level so you can still hear outside noise. Failure to do this may result
in an accident. Bass Habit recommends caution when listening at a high volume.
For safety and enjoyable listening, the sound should be clear without
distortion.
INTERNATIONAL TECHNICAL ENQUIRIES
For international technical support please contact the dealer/distribution
agent for your country.
INSTRUCTIONS
INSTALLATION EXPERIENCE
Installation of Bass Habit amplifiers may require experience with a variety
of mechanical procedures including cable wiring, drilling, etc. This manual
only provides general installation and operation instructions. If you have any
reservations about your installation skills, please contact your local
authorized Bass Habit dealer for help.
CHOOSING AMPLIFIER MOUNTING LOCATIONS
Choose a mounting location in an area where the amplifier will not be damaged,
and where the amplifier is not covered up. Mount the amplifier so that it
remains dry – never mount an amplifier outside the vehicle or in the engine
compartment. Amplifier cooling is essential for proper amplifier operation. If
the amplifier is to be installed in an enclosed space, make sure there is
sufficient air circulation for the amplifier to cool itself. When mounting the
amplifier under a seat, ensure that it is clear of all moving parts and does
not affect the seat functionality. Make sure that the amplifier is mounted
securely using nuts and bolts or the supplied mounting screws.
INSTALLATION PRECAUTIONS NOTE!
Proceed only if you are a qualified installer, otherwise let your dealer do
it.
- Always wear protective eyewear when using tools.
- Turn off all stereo and other electrical devices before you begin.
- Disconnect the (-) negative lead from your vehicle’s battery.
- Keep the amplifier in the package until final installation, and always rest it upwards.
- Never use force when installing a amplifier. · Locate all fuel lines, brake lines, oil lines and electrical cables when planning your installation.
- Check clearances on both sides of a planned mounting surface before drilling any holes or fixing screws.
- When routing cables, keep input-signal cables away from power cables and speaker wires.
- When making connections, make certain all cables are secure and properly insulated.
STEP 1) POWER CONNECTIONS
The Bass Habit Play Power amplifiers are capable of delivering extremely high power levels and require a heavyduty and reliable connection to the vehicle’s electrical system. To get the very best performance out of your Bass Habit Play Power amplifier, carefully follow the instructions below:
GROUND CONNECTION (GND):
Connect the amplifiers Ground (GND) terminal to a solid point on the vehicles
metal chassis, as close to the amplifiers as possible. Scrape away any paint
from this location; use a star-type lock washer to secure the connection.
Minimal ground wire recommended size:
PP70.2 G2: 8 awg / 10mm²
POWER CONNECTION (+12V):
Connect a wire directly to the vehicles positive battery terminal, and
install an appropriate fuse and holder within 30cm/12″ from the battery
terminal. Keep the fuse uninstalled at the time for routing and connecting the
power wire. Be sure to use grommets whenever routing wires through the
firewall or other metal parts. When routing/ connecting is done, installation
of the fuse into fuse holder can be finalised. Minimal power wire recommended
size:
· PP70.2 G2: 8 awg / 10mm²
REMOTE CONNECTION (REM):
Connect the amplifiers Remote (REM) terminal to the source unit Remote turn on
lead using a minimum of 0.75mm²/18 gauge wire. If your source unit does not
have a turn on connection, connect the amplifier (REM) terminal through a
power switch button which can provide a +12V signal.
POWER CONNECTIONS
STEP 2) SPEAKER CONNECTIONS
Speaker output connections should be made using a minimum of 16 awg / 1.25mm² wire. The terminal accepts up to 8 awg/10mm². Minimum total allowed impedance load is 2 Ohm stereo / 4 Ohm Bridge mode.
2-CHANNEL STEREO SPEAKER SYSTEM
1-CHANNEL BRIDGE MODE
STEP 3) SIGNAL CONNECTIONS
Use high quality RCA jacks cable to make sure that you get the full audio
experience.
SIGNAL CABLE CONNECTIONS
CONTROL PANEL
Bass Habit Play Power 2-channels amplifiers can be used for both speakers and
subwoofers. While listening to music, adjust the gain/crossover/subsonic/bass
boost for the least perceived distortion from the speakers, allowing them to
reproduce as much bass as possible.
Input level control (GAIN): GAIN control is a seamless adjustable between 0.2V
– 6V. Tips for adjusting the GAIN control correctly: – Initially turn the GAIN
control to minimum (counter clockwise). – On the source unit, increase the
volume control to the 3/4 of maximum volume. – Slowly increase the GAIN
control until you hear slight distortion in the speaker/speakers. – Then
reduce the GAIN slightly until distortion is no longer heard.
Bass Boost control (BASS BOOST): Bass Boost is adjustable between 0, 6, 12 db
(@ 45Hz) Please use the BASS BOOST knob with care, excessive use can damage
you system!
LPF Crossover (LPF): The low pass filter is seamless adjustable between 50Hz –
500KHz. When using a subwoofer, set the frequency cut point at 60Hz and adjust
to your own preferences.
HPF Crossover (HPF): The high pass filter is seamless adjustable between
50Hz3KHz. The HPF can be used for removing the deepest bass notes from the
subwoofer, get a tighter and more rhythmical sound. For a normal setup the HPF
should be adjusted to the “50 Hz” setting.
Power status & Protection LED: · POWER = Power LED lights up when the
amplifier is turned on. Normally during the start-up sequence the POWER and
PROTECT lights will flash as a selft test procedure. · PROTECT = Protect LED
light flashing or solid. This light is an indicator of the protect mode
status, see the trouble shooting section of the manual for more information.
Line Input: Connect the line outputs from your source unit and connect to the
Line L and R inputs.
SIDE PANEL PP70.2 G2
- I NPUT RCA Rear input
- GAIN Gain control, input signal adjustment 0.2V-6V
- BASS BOOST 6dB/0dB/120dB (45Hz)
- LPF Low Pass Filter 50-500Hz (12db/Oct)
- LPF/FLAT/HPF Filter mode settings
- HPF High Pass Filter 50-3000Hz (12dB/Oct)
- POWER Power indicator (Green)
- PROTECT Protect indicator (Red)
SPECIFICATIONS
| PP70.2 G2
---|---
Component| Class AB amplifier
Number of channels| 2 channels
Power output @ 2 ohm| 2x100W RMS
Power output @ 4 ohm| 2x70W RMS
Bridged power @ 4 ohm| **1x180W RMS *
Power output MAX| 400W MAX
S/N| > 90dB
Frequency response| 20Hz – 20KHz
High Pass Filter| 50Hz – 3KHz
Low Pass Filter| 50Hz – 500Hz
Bass Boost| 0dB / 6dB / 12dB
Bass Boost frequency| 45Hz
Input adjustment| 0.2V – 6V
Operation voltage| 10V – 16V
Fuse rating| 1x40A
Protect| Circuit protection
Current protection
Temperature protection**
RMS Power @ 14.4 V, THD 1%
TROUBLESHOOTING
| Symptom | Check / Control |
|---|
No sound
/ No active POWER LED
| • Check and measure voltage at +12V and REM terminals (allowed working range is 10-16V DC).
• Check and measure ground connections.
• Check external fuse.
• Check input signal and cables from source unit.
• Check speaker wires and terminals.
Noise or Distorted sound
/ Low output
| • Check crossover/input level/control knobs and switches.
• Check ground connections of all installed audio equipment, (source unit, dsp etc.).
• Check speaker wires for possible short circuit.
• Check impedance load of the speaker/speakers according to
the manual.
• Check speaker connections for proper polarity.
Amplifier Protection mode (PROTECT)| • Check impedance load of the speaker/speakers according to
the manual.
• Check chassis ground connections.
• Check speaker wires for possible short circuit.
• Check power input voltage
(allowed working range is 10-16V DC).
• Check RCA input voltage (allowed range is 0.2-6V).
• Check RCA cable for possible short circuit.
The crossed-out wheelie bin symbol means that the product, literature and packaging included must be taken to separate collection at the end of their working life. Do not dispose of these products as unsorted municipal waste: dispose of them at a recycling point. For info on your nearest recycling point, check with your local waste authority. Products marked with the RoHS symbol complies with the relevant provisions of the RoHS Directive for the European Union. In common with all Electrical and Electronic Equipment (EEE) the product should not be disposed of as household waste. Alsternative arrangements may apply in other jurisdictions. The product with the CE mark indicates that it has passed the correspondning conformity assessment procedure and the manufacturer’s declaration of conformity, and it complies with the relevant EU directives, and is used as a pass for the product to be allowed to enter the European Community market. Relevant directives require industrial products to be affixed with the CE mark. Those that do not have the CE mark shall not be marketed.
Winn Scandinavia AB Elementvägen 15, 702 27 Örebro
Sweden www.winnscandinavia.com
Winn Scandinavia reserves for possible typos, factual or numeric errors that may have been printed on any products, package designs, user manuals and/or other included accessories.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>