BASS HABIT SP35H SPL Play 35mm Horn Tweeter User Manual

BASS HABIT SP35H SPL Play 35mm Horn Tweeter

Thank you for purchasing this Bass Habit Tweeter. Please read this manual to fully understand how to get the best result from this product and ensure that the advice on how to look after the product and the safety precautions are followed. We hope you enjoy using the product as much as we enjoyed creating it.

INSTALLATION INSTRUCTION

DO NOT EXPOSE THIS PRODUCT TO EXCESSIVE DAMP OR MOISTURE

• Doing so may result in fire, shock or damage to the product.

BEFORE WIRING, DISCONNECT THE CABLE FROM THE POSITIVE BATTERY TERMINAL

• Failure to do so may result in electric shock or injury.

ENSURE GOOD AND CORRECT CONNECTIONS

• Failure to make the correct connections may result in permanent damage to the product.

DO NOT USE ANY FUNCTIONS THAT MAY TAKE YOUR CONCENTRATION AWAY FROM DRIVING YOUR VEHICLE

• Do not set up your amplifier whilst driving. Doing so may result in an accident. For prolonged interaction with the product, make sure that your vehicle is stationary and parked in a safe location.

KEEP THE VOLUME AT A LEVEL SO YOU CAN STILL HEAR OUTSIDE NOISE

• Failure to do this may result in an accident. Bass Habit equipment is capable of producing sound levels that can permanently damage your hearing. Bass Habit recommends caution when listening at a high volume. For safety and enjoyable listening, the sound should be clear without distortion.

CAUTION

• Never connect any tweeter lead to the car chassis. This can cause severe damage to your car audio set up.
• Before drilling or cutting any holes, investigate the layout of your vehicle thoroughly.
• Use caution when working near the fuel/hydraulic lines and electrical wiring.
• Observe the correct polarity when wiring. Improper phasing may cause a loss of frequency response.
• Ensure that no moving parts catch on the tweeter or grill (e.g. door handles or window glass inside the door).

WARRANTY

All Bass Habit products carry a full warranty depending on the conditions in the country where it is sold. The warranty is valid from the date of the original receipt as proof of purchase (warranty period differs depending on local warranty laws and policies). Contact your international Bass Habit dealer or distributor concerning specific procedures for your country’s warranty policies.

WHAT IS NOT COVERED

• Damage to the product due to improper installation.
• Subsequent damage to other components.
• Damage is caused by exposure to moisture, excessive heat, chemical cleaners, and/or UV radiation.
• Damage through negligence, misuse, accident, or abuse. Repeated returns for the same fault may be considered abuse.
• Any cost or expense related to the removal and/or abuse. Repeated returns for the same fault may be considered as abuse.
• Damage caused by amplifier clipping or distortion.
• Items repaired or modified by any unauthorized repair facility.
• Return shipping on non-defective items.
• Products returned without a return authorization number.
• Damage to the product due to the use of sealant.

WARNING
Bass Habit equipment is capable of sound pressure levels that can cause permanent damage to your hearing and those around you. Please use common sense when listening to your audio system and practice safe sound.

INTERNATIONAL TECHNICAL ENQUIRIES
For international technical support please contact the distribution agent for your country.

SPECIFICATION

(3,3 uF capacitor included)

Outer Diameter| 98 mm
Total Height| 97,5 mm
Weight (pcs)| 0,7 KG

INSTRUCTIONS

INSTALLATION EXPERIENCE
Installation of Bass Habit tweeters may require experience with a variety of mechanical procedures including enclosure construction. This manual only provides general installation and operation instructions. If you have any reservations about your installation skills, please contact your local authorized Bass Habit dealer for help.

CHOOSING TWEETER MOUNTING LOCATIONS
Choosing the correct tweeter mounting location will have the greatest effect of the sound quality of the system. There are many different considerations needed when choosing the location(s) that best meet your needs. The location(s) must be large enough for the tweeter to fit. Care is needed to ensure that the desired location will not affect either the mechanical or electrical operation of the vehicle.

WARNING! The use of silicone rubber to seal in a tweeter will void the warranty. If any sealing is needed in addition to the tweeter’s gasket, use a caulking cord or vinyl weather strip.

INSTALLING THE TWEETER

1. Determine where the tweeter will be mounted. Make sure there is a flat area large enough for the speaker to fit properly. An uneven mounting surface can damage the tweeter.
2. Check to make sure the space you have selected for the tweeter will not interfere with vehicle operation.
3. If a template is included in the packaging, use the template and mark the hole with a pen.
4. Cut the hole for the tweeter. A hole can be cut either with a pair of metal tin snips, a saber or jig saw.
5. Run speaker wire (not included) to the tweeter. Make sure to keep wires away from sharp metal or other rough edges. When passing through metal, use a grommet to protect the wires from sharp edges.
6. Pre-drill the mounting holes using a 1/8” (3mm) drill bit.
7. Pull the wire through the tweeter opening and connect it to the tweeter. Be sure to observe proper polarity.
8. Mount the tweeter using good-quality screws.
9. Always use the inline crossover capacitor when included. Failure to use crossover(s) may cause damage to the tweeter(s).

The crossed-out wheelie bin symbol means that the product, literature, and packaging included must be taken to a separate collection at the end of their working life. Do not dispose of these products as unsorted municipal waste: dispose of them at a recycling point. For info on your nearest recycling point, check with your local waste authority.

Products marked with the RoHS symbol comply with the relevant provisions of the RoHS Directive for the European Union. In common with all Electrical and Electronic Equipment (EEE) the product should not be disposed of as household waste. Alternative arrangements may apply in other jurisdictions.

The product with the CE mark indicates that it has passed the corresponding conformity assessment procedure and the manufacturer’s declaration of conformity, and it complies with the relevant EU directives and is used as a pass for the product to be allowed to enter the European Community market. Relevant directives require industrial products to be affixed with the CE mark. Those that do not have the CE mark shall not be marketed.

Winn Scandinavia reserves for possible typos, and factual or numeric errors that may have been printed on any products, package designs, user manuals, and/or other included accessories.
Winn Scandinavia AB Elementvägen 15, 702 27 Örebro Sweden: www.winnscandinavia.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>