FOAMit FG-10NK-2 10 Gallon Air Operated Portable Fog Equipment User Manual

FOAMit FG-10NK-2 10 Gallon Air Operated Portable Fog Equipment User Manual

WARNING

Read this manual completely and understand the machine before operating or servicing it.

• Read all instructions before installing or operating unit.
• Always wear appropriate personal protective equipment (PPE) when operating or servicing unit.
• Always follow all chemical safety precautions and handling instructions provided by the chemical manufacturer and Safety Data Sheet (SDS).
• If this unit is modified or serviced with parts not listed in this manual, the unit may not operate correctly.
• Always depessurize unit after use (as described in the After Use Instructions).
• Do not exceed an incoming air pressure of 100 psi (7 bar).
• Do not exceed a fluid temperature of 100˚F (37˚C).
• Always flush the unit with fresh water for 5 minutes when switching from an alkaline to an acid or an acid to an alkaline.
• Never use unit with hydrocarbons or flammable products.
• Only use clean and dry air. Air must be filtered and free of moisture or pump life will be diminished. If needed, install an air dryer before unit.
• Do not use an air lubricator before the unit.
• Never use unit if it is damaged or leaking.

PROTECT THE ENVIRONMENT

Please dispose of packaging materials, old machine components, and hazardous fluids in an environmentally safe way according to local waste disposal regulations.

**** Always remember to recycle.

Specifications and parts are subject to change without notice.

OPTIONS

| Pump Seal Material| -2
---|---|---
FG-10N| Santoprene ( standard )
Viton ( V )
Kalrez ( K )
Add bold option codes to item number as shown. For standard options, no option code is needed. Examples:
FG-10N-2 (standard unit with Santoprene pump seals)
FG-10NV-2 (unit with Viton pump seals)

REQUIREMENTS

formulated for this type of application and compatible with unit materials and pump seals. For more information on chemical compatibility, consult the manufacturer or SDS for your product or contact our customer service department.

SPECIFICATIONS

(up to system max of 47,320 cubic feet).
Run time from full tank**| Approx. 1.5 hours
Number of nozzles| 2 nozzles
Wheel type| Two 10 inch non-marking wheels

Dilution rates and flow rates given are based on chemical with viscosity of water and factory air pressure settings.
Area covered and run time may vary based on humidity, air flow, and product used.

Operation Instructions

Always follow all chemical safety precautions and handling instructions provided by the chemical manufacturer and Safety Data Sheet (SDS).

1. Follow all instructions from chemical manufacturer. Fill the tank with water and the advised percentage of chemical concentrate.
2. Place the unit in the area to be fogged.
3. Ensure the air supply valve (BVB14) is in the closed position, and connect a compressed air line to the air inlet fitting (AP25).
4. Open the air supply valve (BVB14) to activate the unit.
5. Evacuate the area.
6. After the unit has stopped fogging, observe all appropriate safety precautions before reentering area. Close the air supply valve (BVB14) and disconnect the compressed air line from the unit.

After Use Instructions

1. Flush the unit with fresh water for 5 minutes.
2. Disconnect the air line from the air fitting (AP25).

Maintenance Instructions

To keep your portable unit operating properly, periodically perform the following maintenance procedures:

• Check the air pump (P56/P56K/P56V) for wear and leaks.
• Inspect hoses for leaks or excessive wear. Make sure all hose clamps are in good condition and properly secured.
• Check the suction tube and screen for debris and clean as needed.
• Drain compressor tank on a regular basis to ensure proper operation of pump.

Troubleshooting Instructions

• If air passes through the pump (P56/P56K/P56V) without cycling, the pump needs to be replaced.
• Check the chemical suction line and strainer for debris or damage. Clean or replace as needed. To prevent damage to the unit, the strainer (STR38-IL) must always be used.
• Check for proper air pressure on air gauge (AG100). Air regulator (R14) is factory set at 50 psi (3.4 bar).
• If the unit foams at a reduced pressure:
  • Check the air compressor supplying the unit. If the pressure is less than 40 psi, turn the foam unit off until the compressor can catch up.
  • If the air supply is 50 psi (3.4 bar) or above, check the AG100, which should read near 50 psi (3.4 bar). If the AG100 is more or less than 50 psi (3.4 bar), adjust the pressure by turning the knob on the top of the air regulator (R14).

TANK ASSEMBLY

ITEM NUMBER: TANK-10N-A

OPTIONAL COMPONENTS

Plate – Inside View

Plate – Back View

FOG NOZZLE ASSEMBLY

PIN
DFP7-C| 7 INCH FILL CAP POLYPRO BLACK
DFP7-F| 7 INCH TANK LID FLANGE POLYPRO
DFP7-PIN| HINGE PIN FOR DFP7-C & DFP7-C
DFP7-C-BL| 7 INCH FILL CAP POLYPRO BLUE PANTONE
DFP7-C-GN| 7 INCH FILL CAP POLYPRO GREEN PANTONE
DFP7-C-RD| 7 INCH FILL CAP POLYPRO RED PANTONE
DFP7-C-YL| 7 INCH FILL CAP POLYPRO YELLOW PANTONE
DP-A| DRAIN PLUG ASSEMBLY FOR TANK-10N TANK-20N
DP| FRONT DRAIN PLUG FOR PORTABLE UNIT POLYPRO
DP-G| FKM SQUARE CUT DRAIN PLUG GASKET
EC14-2| OETIKER CLAMP 13.8
EL14M14F| 1/4 FEM PIPE X 1/4 M PIPE ELBOW
FG-10N-2-BRKT| BRACKET FOR FG-10N-2
FMS1034| 10 X 3/4in PHIL SHEET METAL SS SCREW
FWAX15| FLAT AXLE WASHER
FWLG14| .569 ID X 1.28 OD X .08 THICK FLAT WASHER SS 18-8
H38B-F| 3/8 INCH BLUE HOSE-HYBRID TPE-Available per ft.
H38CP| 3/8IN OD POLYETHYLENE TUBING – NATURAL
HBBEL1414| HOSE BARB 1/4 MPT X 1/4 BARB ELBOW
HBSSEL1438| STAINLESS HOSE BARB ELBOW 1/4 INCH NPT X 3/8 HOSE BARB
HHBB1418| HEX HEAD BUSHING 1/4 MPT X 1/8 FPT
HHPB3414| HEX HEAD POLY REDUCER BUSHING 3/4 X 1/4
---|---
P56| 5700 PUMP WITH SANTOPRENE SEALS – INCLUDES HOSE BARBS, AIR FITTING, AND AIR PORT
P56K| 5700 PUMP WITH KALREZ SEALS – INCLUDES HOSE BARBS, AIR FITTING, AND AIR PORT
P56V| 5700 PUMP WITH VITON SEALS – INCLUDES HOSE BARBS, AIR FITTING, AND AIR PORT
20756103B| Polypro G57 Air Port x HB Straight, w/ Viton o-ring
HB14P| 1/4in BRASS HB AIR FITTING /G57/P56
HB5638| HOSE BARB FOR P56 PUMP
HB5638K| HOSE BARB FOR P56K PUMP
HB5638V| HOSE BARB FOR P56V PUMP
PFN-N130| PNEUMATIC FOG NOZZLE – POLYPROPYLENE AND KYNAR TIP – 3.7 GAL/HR PER NOZZLE
PLPF-B| BLANK PORTABLE FOAMER PLATE WITH HINGE W/O HOLES
PLPF-PIN| 302 STAINLESS PORTABLE PLATE HINGE PIN
PVCV34FM| PVC VALVE 3/4in FPT X 3/4in MPT
QF1438| MALE CON. 3/8in TUBE X 1/4in MPT – POLYPROPYLENE
QF5638| 3/8in QF PUMP FITTING / G57
QFBH38| BULKHEAD 3/8in TUBE POLYPROPYLENE
QFEL1438| FIXED ELBOW 3/8in TUBE X 1/4in MPT – POLYPROPYLENE
QFSEL38| PLUG-IN ELBOW 3/8in TUBE X 3/8in POLYPROPYLENE
QFT38| UNION TEE 3/8in TUBE POLYPROPYLENE
R14| 1/4 NPTF REGULATOR W/ FILTER-NO GAUGE
SSA14| SS304 MALE/FEMALE ADAPTOR 1/4 NPT X 1/4 NPT
SSAXLE14| 14 ½” long with the 5/8” diameter bar & 2 through holes with countersinks beveled ends
SSC38| WORM GEAR CLAMP, S/S (.25-.63)
SSP12| STAINLESS STEEL AXLE PLATE – 2.5 inch X 1 inch – 2 HOLE
STR38-IL| IN LINE STRAINER 3/8 BARB 20 MESH 304 STAINLESS EDPM GSKT
TANK-10N| 10 GALLON NATURAL TANK
TW916| 1/2 INT TOOTH L/W 410SS
W15| NONMARKING WHEEL FOR PORTABLE UNITS
WS-20CFM| TSUNAMI WATER SEPARATOR 20 CFM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>