HAMPTON BAY 564291010 9-Inch Color Selectability Flushmount User Guide
- June 5, 2024
- HAMPTON BAY
Table of Contents
HAMPTON BAY 564291010 9-Inch Color Selectability Flushmount User Guide
PACKAGE CONTENTS
Part
|
Description
|
Quantity
---|---|---
A
|
Fixture Body
|
1
HARDWARE INCLUDED
Part
| Description| Quantity
---|---|---
AA|
Mounting Bracket
| 1
BB
| Mounting Screw (for Bracket)| 2
CC| Wire Connector|
3
NOTE: Keep your receipt and these instructions for proof of purchase.
WARNING: RISK OF ELECTRIC SHOCK. Ensure the electricity to the wires you
are working on is shut off. Either remove the fuse or turn off the circuit
breaker before removing an existing light fixture or installing the new one.
If you are unfamiliar with electrical installations, we recommend you contact
a qualified electrician to do the installation.
INSTALLATION
Select a suitable location that can support the weight of the fixture. Determine the method for mounting the fixture before drilling, based on the type of ceiling.
-
Pass the hot and neutral (black and white) wires from the electrical outlet box through the middle hole of the mounting bracket (AA)
Align the mounting bracket (AA) using the mounting screws (BB) and tighten securely to the electrical box. -
Connect the hot and neutral (black and white) wires from the J-box to the same color wires from the fixture body (A). Connect the grounding wire from the J-box to the green wire from fixture base (A). Cover the wire connections using the wire connectors (CC). Make sure to fasten them well.
-
Cover the wire connectors (CC) with electrical tape for a more secure connection.
-
Position the wires back inside the electrical box.
-
Align the side slots on the fixture body (A) with the mounting bracket (AA) and fix the fixture body (A) securely by carefully rotating in clockwise the side slots inside the mounting bracket (AA).
-
Restore power at the electrical panel. Turn on the light switch to activate the fixture.
ADJUSTING THE COLOR TEMPERATURE OF THE LIGHT
This LED light fixture allows you to customize the color temperature of the light using three settings: soft white, bright white, or daylight.
- Choose your favorite correlated color temperature (CCT) from three options: 2700k Warm White, 3000k Soft White, or 4000k Bright White.
- Move the toggle switch on the fxture body (A) to make your selection before inserting into bracket or ceiling.
NOTE: The factory setting for the correlated color temperature (CCT) is 2700K.
CARE AND CLEANING
CAUTION: Before attempting to clean the tube and luminaire/light fixture, disconnect the power to the fixture by turning the breaker off or removing the fuse from the fuse box. Clean with a soft, dry cloth. Do not use cleaners with chemicals, solvents, or harsh abrasives. Do not use liquid cleaner on the LEDs, LED driver, or wiring.
TROUBLESHOOTING
Minor problems often can be fixed without the help of an electrician.
WARNING: Before doing any work on the fixture, disconnect power to the light fixture.
| Problem | Possible Cause | Solution |
|---|---|---|
| The fixture will not light. | The power is off. | Ensure the power supply is on. |
| The circuit breaker is off. | Ensure the circuit breaker is in the on position. | |
| There is a bad connection. | Check to ensure proper wire connections are made. |
Contact a qualified electrician.
There is a defective switch.| Contact a qualified electrician.
The fuse blows or the circuit breaker trips when the light is turned on.| The
wires are crossed or the power wire is grounding out.| Check the wire
connections. Contact a qualified electrician or call Hampton Bay customer
service 1-855-HD-HAMPTON.
WARNING: Carefully read and understand the information given in this manual before beginning the assembly and installation. Failure to do so could lead to electric shock, fire or other injures which could be hazardous or even fatal Ensure the electricity to the the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker. • To reduce the possibility of serious injury always take the proper precautions and unpulg the fixture before moving or clearing Risk of fire or electricity shock.
NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna, increase the separation between the equipment and the receiver, connect the equipment into an outlet on a circuit different from that to which the receiver is connected, and consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
WARRANTY
WHAT IS COVERED
The manufacturer warrants this lighting fixture to be free from defects in
materials and workmanship for a period of five (5) years from date of
purchase. This warranty applies only to the original consumer purchaser and
only to products used in normal use and service. If this product is found to
be defective, the manufacturer’s only obligation, and your exclusive remedy,
is the repair or replacement of the product at the manufacturer’s discretion,
provided hat the product has not been damaged through misuse, abuse,
accident, modifications, alterations, neglect, or mishandling.
WHAT IS NOT COVERED
This warranty shall not apply to any product that is found to have been
improperly installed, set-up, or used in anyway not in accordance with the
instructions supplied with the product. This warranty shall not apply to a
failure of the product as a result of an accident, misuse, abuse, negligence,
alteration, faulty installation, or any other failure not relating to faulty
material or workmanship. This warranty shall not apply to the finish on any
portion of the product, such as surface and/or weathering, as this is
considered normal wear and tear.
The manufacturer does not warrant and specifically disclaims any warranty,
whether express or implied, of fitness for a particular purpose, other than
the warranty contained herein. The manufacturer specifically disclaims any
liability and shall not be liable for any consequential or incidental loss or
damage, including but not limited to any labor / expense costs involved in he
replacement or repair of said product. Contact the Customer Service Team at
1-855-HD-HAMPTON or visit www.HAMPTONBAY.com.
Contact Us
Questions, problems, missing parts? Before returning to the store, call
Hampton Bay Customer Service
8 a.m. – 7 p.m., EST, Monday – Friday, 9 a.m. – 6 p.m., EST, Saturday
1-855-HD-HAMPTON | Hamptonbay.com
Retain this manual for future use.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>