OLIGHT Prowess A Versatile EDC Flashlight with Dual Direction Illumination User Manual
- June 6, 2024
- OLIGHT
Table of Contents
OLIGHT Prowess A Versatile EDC Flashlight with Dual Direction
Illumination
Specifications
- Product Name: EDC Flashlight
- Features: Dual-direction illumination, Battery level indicator
Product Usage Instructions
Turning On/Off
To turn on the flashlight, press the power button. To turn it off, press
the power button again.
Adjusting Brightness
The flashlight may have different modes or brightness levels. Refer to the
user manual to adjust the brightness as per your requirement.
Battery Level Indicator
The flashlight is equipped with a battery level indicator. Refer to Figure
11-1 and 11-2 in the user manual to understand how to interpret the battery
level.
Charging the Battery
When the battery runs low, recharge it using the provided charging cable.
Follow the instructions in the user manual for proper charging guidelines.
FAQ (Frequently Asked Questions)
-
Q: How do I replace the batteries?
A: Refer to the user manual for detailed instructions on how to replace the batteries safely. -
Q: Is the flashlight water-resistant?
A: Yes, this flashlight is designed to be water-resistant. However, please refer to the user manual for specific details on water resistance ratings. -
Q: How do I switch between different lighting modes?
A: The user manual provides information on how to switch between different lighting modes. Typically, it involves pressing the power button in a specific sequence.
A versatile EDC flashlight with dual-direction illumination.
IN THE BOX
Multi-language dictionary, see Table 3;
Product specifications, see Table 1 and Table 2;
Operating instructions as below:
2.1 Remove the insulating film before first use, see Figure 1; 2.2 Charge, see Figure 2;
Note:
Indicator
- If you have an MCC charging cable and your charging dock is not available, you can use the MCC charging cable for charging.
- The MCC is not included in the package. If necessary, please purchase it from Olight Store.
- When using the MCC3 charging cable, the charging time is approximately 4.5 hours.
ON/OFF, see Figure 3;
Single press the switch quickly to turn on the light. When turned on, the flashlight will light up at the memorized brightness level. (Moonlight, Low, Medium, and High modes will be memorized when turned off. Turbo mode will be memorized as High mode; High mode output will last for 10 minutes before switching to Medium mode; Strobe mode will not be memorized.) Single press the switch again to turn off the light. The back light retains brightness memory for 1 minute after turning off and switches to the lowest output upon restart.
Lockout/Unlock, see Figure 4;
When the flashlight is off, press and hold the switch (for about 2 seconds) to
access lockout mode (the flashlight will enter Moonlight briefly and then
switch off to signal lockout mode activation). In lockout mode, if you operate
the switch for a non-unlock purpose, the indicator at the center of the switch
will briefly light up red to signal that the light is still in lockout mode.
To unlock it, please press and hold the switch for about one second until the
Moonlight is on.
Moonlight, see Figure 5;
When the flashlight is off, press and hold the switch for over one second to
access the Moonlight mode. If the light was turned off in Moonlight mode,
simply press the switch.
Turbo, see Figure 6;
Front light: Double press the switch quickly to activate Turbo mode, and
double press again to return to the memorized brightness level. If the battery
level is low, it returns to a lower output.
Back light: When the current brightness is ≥70%, double press the switch
quickly to set the flashlight output to the lowest brightness. When the
current brightness is <70%, double press the switch quickly to set it to the
highest available brightness.
Choose between front light and back light, see Figure 7;
Move the toggle switch upward for the front light, and downward for the back
light.
Front light operation
Strobe, see Figure 8;
Press the switch 3 times or more to activate Strobe mode. To quit this
mode, single press or press and hold the switch.
Change brightness level, see Figure 9;
When the light is on, press and hold the switch to adjust brightness. The
flashlight will cycle through Low, Medium, and High modes, starting from the
current brightness level. Release the button to select the desired brightness
level. (Note: Moonlight and Turbo modes are not included in this cycle.)
Change the brightness level of the back light, see Figure 10;
When the light is on, press and hold the switch once to smoothly increase the
brightness, and release to select the brightness level. To decrease the
brightness level, press and hold again to smoothly decrease the brightness
from the current brightness level. When the brightness level reaches its
limits at the brightest or lowest setting, the light will flash twice to
indicate that it has reached the highest or lowest level.
Battery level indicator, see Figure 11-1 & 11-2;
Charging dock application, see Figure 12;
How to use the fixing bracket, see Figure 13；
Begin by using tools to punch holes in the wall or wooden board, then insert
the expansion screws. Next, remove the 3M adhesive sticker on the back of the
fixing bracket and align it with the hole on the wall. Finally, secure the
bracket in place by screwing in the screws.(Note: Please stick the 3M adhesive
sticker on a flat and smooth wall or car panel)
How to take the vertical holster out of the fixing bracket, see Figure 14;
Press the vertical holster against the fixing bracket, then pull it up and out
of the fixing bracket.
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WEEE Disposal a n d Recycling Information
All products bearing this symbol are waste electrical and electronic equipment
(WEEE as in directive 2012/19/EU) which should not be mixed with unsorted
household waste. Instead, to protect human health and the environment, you
should dispose of your waste equipment at a designated collection point for
the recycling of WEEE, appointed by the government or local authorities.
Proper disposal and recycling will help prevent potential negative
consequences to the environment and human health. Please contact the installer
or local authorities for more information about the location as well as terms
and conditions of such collection points.
ISED Notice
This device complies with Industry Canada’s licence-exempt ICES standard(s).
Operation is subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES-005.
The light source of this luminaire is not replaceable
when the light source reaches its end of life the whole luminaire shall be
replaced.
EU Declaration of Conformity
Hereby Dongguan Olight E-Commerce Technology Co,Ltd declares that the
equipment[Prowess] is in compliance with Directive 2014/30/EU and RoHS
Directive 2011/65/EU & (EU) 2015/863. The full text of the EU declarabon of
conformity is available at the following internet address:
https://www.olight.com/download
WARRANTY
We are proud to offer a lifetime warranty in Australia, China, France, Germany, and the USA. We are also working hard to expand coverage to more countries, where we provide a 2 or 5-year warranty. The warranty covers defects in material and workmanship under normal use, excluding loss, theft, deliberate damage, or cosmetic damage. For complete warranty information, please visit Olight.com or your local Olight official website.
UK Customer Support
contact@olightstore.uk
Dongguan Olight E-Commerce Technology Co., Ltd.
4th Floor, Building 4, Kegu Industrial Park, No 6 Zhongnan Road, Changan Town,
Dongguan City, Guangdong, China.
Made in China
References
- Olight | Illuminate Your World.
- Flashlights, Tactical Light, Outdoor Tools - Olight Official Store- Olight
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>