S LAS SL-16N Self Calibrating Power Vent Control and Termination Kit Instruction Manual
- June 6, 2024
- S LAS
Table of Contents
S LAS SL-16N Self Calibrating Power Vent Control and Termination Kit
Product Specifications
- Models: SL-16N, SL-16P, SL-26N, SL-26P, ST-46N, ST-46P, FS-16N-RV, FS-16P-RV, FS-16N-TV, FS-16P-TV, BI-38N-C, BI-38P-C, BI-38N-T, BI-38P-T, 46N-BICZ, 26N-BICZ, 16N-BICZ, BI-48-SSL, BI-48-SSR, BI-48-ST, BI-60-SSL, BI-60-SSR, BI-60-ST, BI-72-SSL, BI-72-SSR, BI-72-ST
- Requires SCPV-900C Self-Calibrating Power Vent Control Module for all power vent installations
- Requires SCPV-TWH-XX Self-Calibrating Power Vent Termination Wire Harness (available in 25, 50, 100, and 150 feet lengths)
- Flush-Mount Termination Specifications
- Surface-Mount Termination Specifications
- Power Vent Clearances
Product Usage Instructions
Installation Instructions
Refer to the specific installation section based on the type of mounting
required: Flush Mount (side wall), Surface Mount (side wall), or Vertical
(thru the roof) Installation.
Electrical Instructions
Follow the electrical instructions provided in the manual for proper setup
and connection of the power vent control module.
Calibration and Operation
- Ensure the SCPV-900C Self-Calibrating Power Vent Control Module is properly installed.
- Use the SCPV-TWH-XX Self-Calibrating Power Vent TerminationW ire Harness as required for your installation.
- Follow the calibration steps outlined in the manual too ptimize the performance of the power vent control module.
Troubleshooting
Refer to the troubleshooting section in the manual if youe ncounter any issues with the power vent system.
This power vent control and termination kit is designed for specific SÓLAS fireplace models for optimal installation and operation.
IMPORTANT SAFETY INFORMATION
Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies. Children and adults should be alerted to the hazards of high surface temperature and should stay away to avoid burns or clothing ignition. Young children should be supervised when they are in the same room as the appliance. Clothing or other flammable material should not be placed on or near the appliance. Keep the room area clear and free from combustible materials, gasoline, and other flammable vapors and liquids.
WARNING: All installation, servicing, and troubleshooting must be performed by a qualified gas technician.
The manual is available in French upon request.
FAQ
Do I need a qualified technician for installation?
Yes, all installation, servicing, and troubleshooting must be performed by a qualified gas technician.
What are the available lengths for the SCPV-TWH termination wire harness?
The termination wire harness is available in 25ft, 50ft, 100ft, and 150ft lengths.
How can I differentiate between termination models?
The termination with a pressure port on the rear top-left corner is different from others and can be identified as such.
What should be done before installing the kit?
Read the manual thoroughly before beginning the installation of the SÓLAS Power Vent Kit and plan the installation in advance by reviewing all the information contained in the manual.
Who should perform the installation and troubleshooting of the power vent control?
All installation, servicing, and troubleshooting must be performed by a qualified gas technician.
Is the manual available in other languages?
Yes, the manual is available in French upon request.
What are the clearance requirements for the power vent?
Maintain a minimum clearance of 1.5 inches (38mm) to combustibles and electrical wiring around the vent pipe.
What should be done if there's an issue with the vent control during operation?
Refer to the Troubleshooting section on page 20 of the manual and contact SÓLAS support if needed.