NITECORE ULM10 Pro USB Travel Charger for Leica BP-SCL5 Batteries User Manual
- June 5, 2024
- Nitecore
Table of Contents
NITECORE ULM10 Pro USB Travel Charger for Leica BP-SCL5 Batteries
Warranty Details
Our authorized dealers and distributors are responsible for warranty service. Should any problem covered under warranty occurs, customers can contact their dealers or distributors in regards to their warranty claims, as long as the product was purchased from an authorized dealer or distributor. NITECORE’s Warranty is provided only for products purchased from an authorized source. This applies to all NITECORE products. To be qualified for warranty, please refer to the “IMPORTANT WARRANTY NOTICE” section on top to validate your product. Any DOA / defective product can be exchanged for a replacement thrOugh a local distributor/dealer within the 15 days of purchase. After 15 days, all defective/ malfunctioning NITECORE® products can be repaired free of charge for a period of 12 months (1 year) from the date of purchase. Beyond 12 months (1 year), a limited warranty applies, covering the cost of labor and maintenance, but not the cost of accessories or replacement parts.
- broken down, reconstructed and/or modified by unauthorized parties
- damaged from wrong operations (i.e. reverse polarity installation, installation of non-rechargeable batteries or failure to obey the warnings)
- damaged by batteries leakage.
For the latest information on NITECORE® products and services, please contact a local NITECORE® distributor or send an email to service@nitecore.com. All images, text and statements specified herein this user manual are for reference purpose only. Should any discrepancy occur between this manual and information specified on www.nitecore.com, information on our official website shall prevail. SYSMAX Innovations Co., Ltd. reserves the rights to interpret and amend the content of this document at any time without prior notice.
IMPORTANT NOTICE CONCERNING WARRANTY SERVICE
Thank you for purchasing! Before using this charger, please find your
verification code on the package box, and go to
http://charger.nitecore.com/validation (or scan the QR code beside the
verification code to visit on your mobile phone). Type in your verification
code and personal information as required, and submit the page. After
verification, Nitecore will send you a warranty service email. This email and
your registration email address are essential to your possible warranty
application. Before you complete the warranty service registration, you cannot
enjoy our warranty service for your purchase.
Features
- Dual slot battery charger
- Compatible with Leica BP-SCL5 camera batteries
- QC 2.0 Available
- USB input
- Real-time information on battery voltage, charging current, battery temperature, charged volume and battery health
- Automatically detects battery health
- Reverse polarity protection and anti-short circuit protection
- Automatic adoption for the optimal charging modes between CC and CV
- Automatic selection for charging current
- Automatic termination upon charging completion
- Activates over-discharged batteries with protective circuits
- Compatible with power banks, 5V solar panels and USB adaptor
- Made from durable and fire retardant PC materials
- Optimal heat dissipation design
- Insured worldwide by Ping An Insurance (Group) Company of China, Ltd.
Accessories
USB Charging Cable
Specifications
- Input: DC 5V/2A or 9V/2A
- Output Voltage: Slot 1 8.25V±1%
- Slot 2 8.25V±1%
- Output Current: QC Mode: 1200mA1 (MAX), 800mA2 (MAX)
- Standard Mode: 700mA*1 (MAX)
- Interface: Input: USB
- Output: connector
- Battery compatibility: Leica camera battery BP-SCL5
- BP-SCL5 Compatible models: M10, M10 MONOCHROM, M10-R
- Dimensions: 125mm×70mm×29mm (4.92” ×2.76” ×1.14”)
- Weight: 97.5g (3.44oz)
Operating Instructions
This product is designed specifically for Leica BP-SCL5 camera battery. It supports charging batteries in both slots simultaneously. The output current is adjusted automatically according to input current to reach the optimal charging setting. This product shall NOT be used with other batteries not specified in this manual.
Charging Modes
The ULM10 Pro has 2 charging modes (QC Mode and Standard Mode). QC Mode: The ULM10 Pro is QC 2.0 available. When connecting to a QC supported device (or adaptor), the display will show “Quick Charge” on the upper left corner. In this status (Input Voltage: 9V), it can charge 2 batteries simultaneously with a max output current of 800mA in either slot, or 1 battery with a max output current of 1,200mA. Standard Mode: In this status (Input Voltage: 5V), it will charge the battery which is put in first with a max output current of 700mA, and then charge the other when the first battery is fully charged.
Automatic Current Adjustment
The ULM10 Pro’s actual output current depends on the maximum power
supplied from the USB power source. The output current will be adjusted
based on the actual power being inputted to the device, increasing its
efficiency while shortening charging duration.
Battery Health Monitoring
Once the battery is inserted, the ULM10 Pro will proceed with an initial low
current test charge to diagnose the battery status. After the diagnosis, the
battery status will be shown as Good, Normal or Poor. Note: Re-insert the
battery when “Poor” appears on screen to eliminate the possibility of a poor
battery contact, replace the battery if “Poor” comes up on screen
consistently.
Reverse Polarity and Anti-Short Circuit Protection
The ULM10 Pro makes use of the mechanical reverse polarity protection.
Inserting incompatible batteries or incorrect battery installation will
prevent the initiation of the charging process. The error message “EE EE” will
come up on the LCD display when a short circuited battery is installed.
Note: When the display shows the error message “EE EE”, please put the battery into the original battery charger for 30 minutes to activate it. If it is still unable to get charged after this, please replace the battery.
Over Discharged Battery Activation
The ULM10 Pro will automatically activate over discharged battery caused by
improper storage or misuse.
NOTE : this function only available for batteries with protective circuit.
Cautions
- The ULM10 Pro is only compatible with Leica BP-SCL5 camera batteries. DO NOT attempt to charge other batteries.
- Moderate heat from this product is to be expected during the charging process, which is normal.
- Operating temperature: -10~40℃ (14~104℉), storage temperature: -20~60℃ (-4~140℉).
- Carefully read all labels on the device to ensure batteries are installed correctly.
- Please connect this charger to power supplies with the input voltage stated in the specifications of the user manual. If the input voltage is too low or too high, it may lead to malfunctions, or even a fire.
- DO NOT charge batteries if there is any sign of faulty or short circuit.
- The charger is designed for adults. Use of the charger by kids under age must be under supervision. Operation, using or cleaning of the charger may NOT be done by kids aged 8 years or younger.
- DO NOT leave the product unattended while it is connected to a power supply. Unplug the product at any sign of malfunction and refer to the user manual.
- Batteries of short lifespan should be replaced as soon as possible.
- DO NOT expose the device to high temperature or incinerate, avoid using the device in environments where drastic changes in temperature are possible.
- Store the device in ventilated areas. DO NOT uses the device in moist environment and keep away from any combustible materials.
- Avoid any shock or impact to the device.
- DO NOT place any conductive or metal object in the device to avoid short circuiting and explosions.
- Unplug the device and remove batteries when it is not in use.
- DO NOT disassemble or modify the device as doing so will render the product warranty invalid. Please refer to the warranty section in the manual for complete warranty information.
- DO NOT misuse in any way! Use for intended purpose and function only.
Disclaimer
This product is globally insured by Ping An Insurance (Group) Company of
China, Ltd. NITECORE shall not be held responsible or liable for any loss,
damage or claim of any kind incurred as a result of the failure to obey the
instructions provided in this user manual.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>