milwaukee M18FBS85 85mm 18V Li-Ion RedLithium Brushless Cordless Bandsaw Instruction Manual

Milwaukee M18FBS85 85mm 18V Li-Ion RedLithium Brushless Cordless Bandsaw

INSTALLATION

**Remove the battery pack before starting any work on the machine

.**

BATTERY

CLEANING

START/STOP

Insulated gripping surface

TIP

BAND SAW SAFETY WARNINGS

• Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a „live“ wire may make exposed metal parts of the power tool „live“ and
• could give the operator an electric shock.
• Wear ear protectors. Exposure to noise can cause hearing loss.
• Always place the guide shoe on the workpiece when sawing.
• Do not start the blade when in contact with the workpiece. Wait for blade to reach full speed before the beginning to cut.
• When blade is binding, or when interrupting a cut for any reason, release the trigger and hold the cutter motionless in the material until the blade comes to a complete stop. Never restart the machine when the blade in contact with workpiece.
• Do not use cracked or distorted saw blades.

ADDITIONAL SAFETY AND WORKING INSTRUCTIONS

• Use protective equipment. Always wear safety glasses when working with the machine. The use of protective clothing is recommended, such as dust mask, protective gloves, sturdy non-slip footwear, helmet and ear defenders.
• The dust produced when using this tool may be harmful to health. Do not inhale the dust. Wear a suitable dust protection mask.
• Do not machine any materials that present a danger to health (e.g. asbestos).
• Switch the device off immediately if the insertion tool stalls! Do not switch the device on again while the insertion tool is stalled, as doing so could trigger a sudden recoil with a high reactive force. Determine why the insertion tool stalled and
• rectify this, paying heed to the safety instructions.
• The possible causes may be:
  •  it is tilted in the workpiece to be machined
  •  it has pierced through the material to be machined
  •  the power tool is overloaded
• Do not reach into the machine while it is running.
• The insertion tool may become hot during use. WARNING! Danger of burns
  •  when changing tools
  •  when setting the device down
• Chips and splinters must not be removed while the machine is running.
• When working in walls ceiling, or fl oor, take care to avoid electric cables and gas or waterpipes.
• Clamp your workpiece with a clamping device. Unclamped workpieces can cause severe injury and damage.
• Remove the battery pack before starting any work on the machine.
• Do not dispose of used battery packs in the household refuse or by burning them. Milwaukee Distributors off er to retrieve old batteries to protect our environment.
• Do not store the battery pack together with metal objects (short circuit risk).
• No metal parts must be allowed to enter the battery section of the charger (short circuit risk).
• Use only System Milwaukee 18 V chargers for charging System Milwaukee 18 V battery packs. Do not use battery packs from other systems.
• Never break open battery packs and chargers and store only in dry rooms. Keep dry at all times.
• Battery acid may leak from damaged batteries under extreme load or extreme temperatures. In case of contact with battery acid wash it off immediately with soap and water. In case of eye contact rinse thoroughly for at least 10 minutes and
• immediately seek medical attention.
• Warning! To reduce the risk of fi re, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack or charger in fl uid or allow a fl uid to fl ow inside them. Corrosive or conductive fl uids, such as seawater,
• certain industrial chemicals, and bleach or bleach containing products, etc., can cause a short circuit.

SPECIFIED CONDITIONS OF USE

The Band Saw cuts lengthways and mitre accurately in diff erent type of metals such as metal profi les (UniStrut), pipes, metal studs, channels, aluminium profi les, metal sheets.
Do not use this product in any other way as stated for normal use.

EC-DECLARATION OF CONFORMITY

• We declare under our sole responsibility that the product described under “Technical Data” fulfi lls all the relevant regulations and the directives 2011/65/EU (RoHS), 2014/30/EU, 2006/42/EC, and the following harmonized standards have been used:
• EN 60745-1:2009 + A11:2010
• EN 60745-2-20:2009
• EN 55014-1:2017+A11:2020
• EN 55014-2:2015
• EN IEC 63000:2018
• Winnenden, 2020-11-04
• Alexander Krug
• Managing Director
• Authorized to compile the technical fi le.
• Techtronic Industries GmbH
• Max-Eyth-Straße 10
• 71364 Winnenden
• Germany

GB-DECLARATION OF CONFORMITY

• We declare as the manufacturer under our sole responsibility that the product described under “Technical Data” fulfi lls all the relevant provisions of the following Regulations S.I. 2008/1597 (as amended), S.I. 2016/1091 (as amended), S.I.
• 2012/3032 (as amended) and that the following designated standards have been used:
• BS EN 60745-1:2009 + A11:2010
• BS EN 60745-2-20:2009
• BS EN 55014-1:2017+A11:2020
• BS EN 55014-2:2015
• BS EN IEC 63000:2018
• Winnenden, 2020-11-04
• Alexander Krug
• Managing Director
• Authorized to compile the technical fi le.
• Techtronic Industries GmbH Max-Eyth-Straße 10 71364 Winnenden Germany

BATTERIES

• Battery packs which have not been used for some time should be recharged before use.
• Temperatures in excess of 50°C (122°F) reduce the performance of the battery pack. Avoid extended exposure to heat or sunshine (risk of overheating).
• The contacts of chargers and battery packs must be kept clean.
• To obtain the longest possible battery life remove the battery pack from the charger once it is fully charged.
• For battery pack storage longer than 30 days:
• Store the battery pack where the temperature is below 27°C and away from moisture
• Store the battery packs in a 30% – 50% charged condition Every six months of storage, charge the pack as normal.

BATTERY PACK PROTECTION

• In extremely high torque, binding, stalling and short circuit situations that cause high current draw, the tool will stop for about 2 seconds and then the tool will turn OFF.
• To reset, release the trigger.
• Under extreme circumstances, the internal temperatur of the battery could become to high. If this happens, the battery will shut down.

TRANSPORTING LITHIUM BATTERIES

• Lithium-ion batteries are subject to the Dangerous Goods Legislation requirements.
• Transportation of those batteries has to be done in accordance with local, national and international provisions and regulations.
  •  The user can transport the batteries by road without further requirements.
  •  Commercial transport of Lithium-Ion batteries by third parties is subject to Dangerous Goods regulations. Transport preparation and transport are exclusively to be carried out by appropriately trained persons and the process has to be
• accompanied by corresponding experts.
• When transporting batteries:
  •  Ensure that battery contact terminals are protected and insulated to prevent short circuit.
  •  Ensure that battery pack is secured against movement within packaging.
  •  Do not transport batteries that are cracked or leak. Check with forwarding company for further advice

MAINTENANCE

• The ventilation slots of the machine must be kept clear at all times.
• Use only Milwaukee accessories and Milwaukee spare parts. Should components need to be replaced which have not been described, please contact one of our Milwaukee service agents (see our list of guarantee/service addresses).
• If needed, an exploded view of the tool can be ordered. Please state the machine type printed as well as the
• six-digit No. on the label and order the drawing at your local service agents or directly at: Techtronic Industries GmbH, Max-Eyth-Straße 10, 71364 Winnenden, Germany.

SYMBOLS

• CAUTION! WARNING! DANGER!
• Remove the battery pack before starting any work on the machine.
• Please read the instructions carefully before starting the machine.
• Keep hands away from rotating parts.
• Always wear goggles when using the machine.
• Wear gloves!
• Do not dispose electric tools, batteries/rechargeable batteries together with household waste material.
• Electric tools and batteries that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.
• Check with your local authority or retailer for recycling advice and collection point.
• n0 Stroke rate under no-load
• Volts
• Direct current
• European Conformity Mark
• British Confomity Mark
• Ukraine Conformity Mark
• EurAsian Conformity Mark

TECHNICAL DATA

• Production code………………………………………………………………… …………………4812 72 01 …000001-999999

• No-load speed…………………………………………………………………….. ..0-164,59 m/min

• Blade size……………………………………………………………………. 899 x 13 x 0,51 mm

• Cutting capacity rectangular stock………………………………………………… 85 x 85 mm

• Cutting capacity Pipe……………………………………………………………………. ø 85 mm

• Battery voltage…………………………………………………………………………………. V

• Weight according EPTA-Procedure 01/2014 (2.0 Ah…12 Ah) ….. ……………… 3,9. 5,0 kg

• Recommended ambient operating temperature …………………….. …………………. -18. +50 °C

• Recommended battery types………………………………………………. ………………. M18B. M18HB

• Recommended charger ……………………………………………………… M12-18C, M12-18AC, M12-18FC, M1418C6

• Noise/vibration information
  

• Measured values determined according to EN 60 745. Typically, the A-weighted noise levels of the tool are:

• Sound pressure level (Uncertainty K=3dB(A))…………………………………… 82,63 dB (A)

• Sound power level (Uncertainty K=3dB(A))………………………………………. 93,63 dB (A)

• Wear ear protectors!
  

• Total vibration values (vector sum in the three axes) determined according to EN 60745.

• Sawing of metal

• Vibration emission value a……………………………………………………………. 1,38 m/s2

• Uncertainty K= ………………h …………………………… 1,50 m/s2

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>