Freemie FG090 Rose Breast Pump System User Guide
- June 5, 2024
- Freemie
Table of Contents
- Freemie FG090 Rose Breast Pump System User Guide
- Get to Know Your Freemie
- 1 Charge Your Pump
- 2 Clean Your Parts
- 3 Put Cups Together
- 4. Add SlimFit Fitmie Inserts
- 5 Add Cups to Pump
- 6. Test Before Use
- 7 Ready to Pump
- 8 Pump Controls
- 9. After Pumping
- Milk Transfer
- Pumping Positions
- Poor Pumping Positions
- Finding Your Best Flange Fit
- Choosing Another Size
- Read More About This Manual & Download PDF:
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Freemie FG090 Rose Breast Pump System User Guide
Get to Know Your Freemie
1 Charge Your Pump
Before first use, charge battery 2-3 hours to optimize battery life. A full charge will provide about 21/2 hours of operation, depending on settings used.
2 Clean Your Parts
Prior to First Use: Boil these parts in large uncovered pots for 10 minutes while stirring.
After Each Use: Clean these parts with hot soapy water and rinse well.
These parts do not come into contact with milk and need not be cleaned in between use.
Note: See digital User Manual for complete use and care instructions
- To avoid damage or malfunction DO NOT use abrasives, brushes, UV or steam sterilization on any Freemie Cup parts.
- Assemble dry parts just before use, and leave parts disassembled in between use
3 Put Cups Together
-
Place Valve onto Valve Base.
-
Insert Barrier into Valve Base.
-
Press assembled Valve Base onto Flange…
-
Align Cup Tab with Flange Tubing Port and press together until you hear the Cup “snap” closed.
4. Add SlimFit Fitmie Inserts
SlimFit5 Cups come with 2 sets of Inserts to add to the 30mm hard Breast
Flange.
Size down with the 25mm or 28mm purple SlimFit Fitmie Inserts. Review Flange
Fit section to make sure you are using the correct size.
SlimFit Fitmie work only with SlimFit Cups and come in sizes 15mm – 28mm
5 Add Cups to Pump
6. Test Before Use
Prior to placing Cups in your bra:
- Turn on pump.
- Set pump to strongest setting (5/Turbo).
- Barrier inside Cup collapses and releases when assembly is correct.
7 Ready to Pump
Place Cups in your bra:
- Bra fit is critical for proper use. Enough pressure is needed to seal the Flange against the breast while too much pressure may cause low output.
- Before choosing a bra, pump by holding the Cups in place with your hands. Then try several of your bras to find one that most closely holds the Cups like your hands.
- It may be necessary to adjust your bra to find the best fit for you. A sports bra or stretchy nursing bra can work well
8 Pump Controls
9. After Pumping
- Turn the pump o.
- Pull Tubing from the tops of the Cups to disconnect.
- Carefully remove Cups from your bra
Cups may be set flat before transferring milk to storage
Milk Transfer
Pour milk quickly and confidently into a storage bag or bottle of your choice.
Pumping Positions
A range of pumping positions are possible with Freemie. Mind the pour spout!
Poor Pumping Positions
Freedom of movement with Freemie depends on:
- How Cups are oriented on your breasts
- Security of Cups in your bra
- Amount of milk in Cups
- How much Cups are jostled
Finding Your Best Flange Fit
Finding the best Breast Flange fit cannot simply be done by measuring your
nipples because some nipples stretch more than others under suction. You can
estimate your size, but some trial and error may be needed for you to optimize
your comfort and milk output.
Experiment to find the right fit and keep in mind:
- You may need a deferent size than the Flanges provided.
- You may need a deferent size for each nipple because no one is perfectly symmetrical.
- You may prefer higher suction, making Flange comfort crucial.
- Your nipple may expand in diameter and length while pumping and may change over time, so keep all of your sizes.
Choosing Another Size
Use a ruler or coin diameters to estimate your erect nipple base size, and
review the Flange fit details below.
Choose the nearest size Flanges or Fitmie Inserts that are slightly larger
than your nipple
SlimFit Fitmie sizes (15mm – 28mm) available at www.freemie.com
Important: Your bra needs to apply enough pressure to create a good seal on
your skin so that air does not leak in and reduce suction. Too much pressure
can pinch or obstruct ducts and reduce your milk output.
Need more milk capacity? Try SlimFit6 or Standard Cups.
Spare parts and additional Freemie SlimFit Fitmie sizing inserts available at www.freemie.com
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>