freemie Independence II Hands Free Wearable Breast Pump User Guide
- June 4, 2024
- Freemie
Table of Contents
freemie Independence II Hands Free Wearable Breast Pump
Get to Know Your Freemie
Charge Your Pump
Before first use, charge battery
2-3 hours to optimize battery life. A full charge will provide approximately 2
1/2 hours of operation.
Clean Your Parts
Prior to Use:
Boil these parts in large uncovered pots for 10 minutes while stirring.
After each use: Clean these parts with hot soapy water and rinse well.
Tubing parts do not come into contact with milk and need not be cleaned between use.
- T o avoid damage or malfunction DO NOT use abrasives, brushes,UV or steam sterilization on any Freemie Cup parts.
- Assemble dry parts just before use, and leave parts disassembled in between use.
Note: See digital User Manual for complete use and care instructions.
Put Cups Together
-
Place Barrier onto Flange.
-
Press Valve onto Valve Base.
-
Guide Valve Base over Barrier .
Incorrect assembly may cause poor suction or malfunction. -
and press together firmly.
-
Align Cup Arrow with Tubing Port and snap closed.
-
Listen for the “snap” to ensure Cup closed.
Add Cups to Pump
Test Before Use
Prior to placing Cups in your bra:
- Turn on pump.
- Set SUCTION Setting (pink lights) to 10.
- Set CYCLE Setting (blue lights) to 10.
- Barrier inside Cup collapses and releases when assembly is correct.
If Barrier does not move, reassemble Cups and check all Tubing connections.
Ready to Pump
Place Cups in your bra
-
Bra fit is critical for proper use.
Enough pressure is needed to seal the Flange against the breast while too much pressure may cause low output. -
Before choosing a bra, pump by holding the Cups in place with your hands. Then try several of your bras to find one that most closely holds the Cups like your hands.
-
It may be necessary to adjust your bra to find the best fit for you. A sports bra or stretchy nursing bra can work well.
Pump Controls
Suction Setting
Pink Indicator Lights:
1=Low
10=Strong
Cycle Setting
Blue Indicator Lights:
1=Fast
10=Slow
Turbo: Slowest suction and release cycle (press Cycle up one time after 10).
You may find it helpful to start with a weaker Suction and faster Cycle to trigger the Stimulation Phase and adjust to a stronger Suction and slower Cycle as you move into the Expression Phase.
After Pumping
- Turn the pump off.
- Pull tubing from the tops of the Cups to disconnect.
- Carefully remove Cups from your bra.
Milk Transfer
Pour milk quickly and confidently into a storage bag or bottle of your choice.
Pumping Positions
A range of pumping positions are possible with Freemie. Mind the pour spout!
Good Pumping Positions
Advanced Technique: Requires re-orientation of cups inside bra.
Poor Pumping Positions
Freedom of movement with Freemie depends on:
- How Cups are oriented on your breasts
- Security of Cups in your bra
- Amount of milk in Cups
- How much Cups are jostled
Clothing Clip
Pump comes assembled with Clothing Clip and is intended to move a bit when
worn. Not intended for vigorous activity like running.
Remove Clip
Finding Your Best Flange Fit
Finding the best Breast Flange fit cannot simply be done by measuring your
nipples because some nipples stretch more than others under suction. You can
estimate your size, but some trial and error may be needed for you to optimize
your comfort and milk output.
Experiment to find the right fit and keep in mind:
- You may need a different size than the Flanges provided.
- You may need a different size for each nipple because no one is perfectly symmetrical.
- You may prefer higher suction, making Flange comfort crucial.
- Your nipple may expand in diameter and length while pumping and may change over time, so keep all of your sizes.
Comfort is key!
It may take a few tries to find what works.
Choosing Another Size
Use a ruler or coin diameters to estimate your erect nipple base size, and
review the Flange fit details below. Choose the nearest size Flanges or Fitmie
inserts that are slightly larger than your nipples.
Fitmie sizes: 15mm – 26mm sold separately.
Flange is too small
for the nipple to move freely in and out of Flange. May cause rubbing or
chafing.
Flange is too big
allowing too much breast and areola tissue to be drawn into Flange. May cause
bruising.
Flange is correct size
With properly fitted Flanges the nipple moves in and out of the Flange freely.
Important: Your bra needs to apply enough pressure to create a good seal on your skin so that air does not leak in and reduce suction. Too much pressure can pinch or obstruct ducts and reduce your milk output.
Hands-Free Wearable Breast Pump
Spare parts and Fitmie inserts available at
www.freemie.com
Freemie Independence II Standard System includes size 25mm Breast Flanges.
Freemie Independence II Deluxe System includes sizes 25mm and 28mm Breast
Flanges.
Scan code to read User Manual.
Visit www.freemie.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>