freemie FG084 SlimFit5 Hands Free Ultra Discreet Collection Cups User Guide
- June 4, 2024
- Freemie
Table of Contents
FG084 SlimFit5 Hands-Free
Ultra Discreet Collection Cups
User Guide
Get to Know Your Freemie SlimFit5 Cups
Clean Your Parts
Prior to First Use: Boil these parts in large uncovered pots for 10 minutes while stirring.
- To avoid damage or malfunction DO NOT use abrasives, brushes, UV or steam sterilization on any Freemie Cup parts.
- Assemble dry parts just before use, and leave parts disassembled in between use.
After Each Use: Clean these parts with hot soapy water and rinse well.
These parts do not come into contact with milk and need not be cleaned in between use. Note: See digital User Manual for complete use and care instructions.
put Cups Together
Incorrect assembly may cause poor suction or malfunction.
- Place Valve onto Valve Base.
- Insert Barrier into Valve Base.
- Press assembled Valve Base onto the Flange…and press together firmly.
- Align Cup Tab with Flange Tubing Port and press together until you hear the Cup “snap” closed.
|
---|---
Add SlimFit Fitmie Inserts
SlimFit5 Cups come with 2 sets of Inserts to add to the 30mm hard Breast
Flange.
Size down with the 25mm or 28mm purple SlimFit Fitmie Inserts. Review the
Flange Fit section to make sure you are using the correct size.|
SlimFit Fitmie work only with SlimFit Cups and comes in sizes 15mm – 28mm.
Add Cups to Pump
Test Before Use
Prior to placing Cups in your bra:
- Turn on the pump.
- Set the pump to the strongest setting.
- Barrier inside the Cup collapses and releases when the assembly is correct. If the Barrier does not move, reassemble the Cups and check all Tubing connections.
Ready to Pump
Place Cups in your bra:
-
Bra fit is critical for proper use.
Enough pressure is needed to seal the Flange against the breast while too much pressure may cause low output. -
Before choosing a bra, pump by holding the Cups in place with your hands.
Then try several of your bras to find one that most closely holds the Cups like your hands. -
It may be necessary to adjust your bra to find the best fit for you. A sports bra or stretchy nursing bra can work well.
After Pumping
- Turn the pump off.
- Pull Tubing from the tops of the Cups to disconnect.
- Carefully remove Cups from your bra. Cups may be set flat before transferring milk to storage. When set flat, Cups may gently rock and then naturally balance.
Milk Transfer
Pour milk quickly and confidently into a storage bag or bottle of your choice.
Pumping Positions
A range of pumping positions are possible with Freemie. Mind the pour spout!
Good Pumping Positions
Advanced Technique: Requires re-orientation of cups inside the bra.
Poor Pumping Positions
Freedom of movement with Freemie depends on:
- How Cups are oriented on your breasts
- Security of Cups in your bra
- Amount of milk in Cups
- How much Cups are jostled
Finding Your Best Flange Fit
Finding the best Breast Flange fit cannot simply be done by measuring your
nipples because some nipples stretch more than others under suction. You can
estimate your size, but some trial and error may be needed for you to optimize
your comfort and milk output.
Experiment to find the right fit and keep in mind:
- You may need a different size than the Flanges provided.
- You may need a different size for each nipple because no one is perfectly symmetrical.
- You may prefer higher suction, making Flange comfort crucial.
- Your nipple may expand in diameter and length while pumping and may change over time, so keep all of your sizes.
Comfort is key!
It may take a few tries to find what works.
Choosing Another Size
Use a ruler or coin diameters to estimate your erect nipple base size, and
review the Flange fit details below.
Choose the nearest size Flanges or Fitmie Inserts that are slightly larger
than your nipples.
SlimFit Fitmie sizes (15mm – 28mm) are available at
www.freemie.com.
The flange is too small
for the nipple to move freely in and out of Flange. It May cause rubbing or
chafing.| The flange is too big
allowing too much breast and areola tissue to be drawn into Flange. It May
cause bruising.| The flange is the correct size
With properly fitted Flanges the nipple moves in
and out of the Flange freely.
---|---|---
| |
Important: Your bra needs to apply enough pressure to create a good seal on
your skin so that air does not leak in and reduce suction. Too much pressure
can pinch or obstruct ducts and reduce your milk output.
Need more depth? Try SlimFit6 or Standard Cups.
SlimFit5 Hands-Free
Ultra Discreet Collection Cups
Spare parts and additional Freemie SlimFit Fitmie
available at www.freemie.com
Scan code to read User Manual.
Visit
www.freemie.com
https://qrco.de/bcIJ8T
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>