AnkerMake M5-V8111-QSG 3D Printing Frontier User Guide
- June 9, 2024
- AnkerMake
Table of Contents
M5-V8111-QSG 3D Printing Frontier
User Guide
AT A GLANCE
Indicator Light* | Description |
---|---|
Flashing Orange Slowly | Heating up |
Fading Green Repeatedly | Printing |
Flashing Red | An alarm is going off |
- For more indicator light status, visit https://www.ankermake.com.
Product Name: AnkerMake M5 Model: V8111
ASSEMBLING THE PRINTER
What You Need Step 1. Installing Gantry Frame
-
Open the box, then place the foam cover on the ground.
-
Take out all the accessories in the foam, then place the protection foam on the ground as support.
-
Take out the gantry frame with its protection foam and place it on the support foam.
-
Take the gantry frame out of the packaging foam, then put it back as shown below.
-
Detach the bottom cover from the platform.
-
Mount the platform through the holes.
-
Fasten screws into the platform.
Step 2. Wiring
-
Connect the motor wires.
-
Connect and fix the USB-C cables with screws.
-
Put the bottom cover back onto the platform.
Step 3. Installing Filament Holder
Secure the filament holder with screws.
Step 4. Connecting to Power
-
Connect the printer to a power outlet with the power cable, then power on the printer.
-
Follow instructions on the touch screen to complete the initial setup.
SETTING UP THE SYSTEM
-
Download and install the AnkerMake app, then sign up for an account.
-
Follow on-screen instructions to add the printer to your device list and connect it to Wi-Fi.
LEVELING HEAT BED
On the touch screen, go to Control > Auto-Level to level the heat bed.
LOADING FILAMENT
-
Place the filament onto the holder.
-
Cut the tip of the filament at a 45° angle.
-
Insert the filament until it reaches the extruder. Then press and hold the button on top of the extruder while continuing to insert the filament. Stop when you feel some resistance.
-
On the touch screen, tap Load on Control > Extrude.
Wait until filament flows out of the nozzle, then tap Stop.
INSTALLING ANKERMAKE SLICER
For the best printing experience, download and install AnkerMake Slicer to
your computer from ankermake.com/software.
The AI recognition capabilities will be not available when the printer works
with other 3D slicer software, such as Cura and Simplify3D.
SAFETY
- The power cord shall be connected to socket-outlet with earthing connection.
- The power supply should be installed near the equipment and the socket-outlet must be easily accessible.
- Only use the power cord provided by the manufacturer. Using unauthorized power cords may cause danger and violate the authorization of the product as well as the guarantee.
- Plug of the power cord is considered as the disconnect device. Once unplugged, the product is considered to be disconnected from the power source.
- Do not use the device in an environment where the temperature is too high or too low. Never expose the device to strong sunshine or wet environments.
- The suitable temperature range for the product and its accessories is 15-35 oC.
- It is recommended to supply the device in an environment with a temperature that ranges from 15℃ ~25℃ .
- When supplying, place the device in an environment that has a normal room temperature and good ventilation.
- This equipment is not suitable for use in locations where children are likely to be present. This equipment is not intended for use by children.
- Moving parts. Keep body parts away from moving parts.
- CAUTION Hot parts. Do not touch.
- Do not use the product in any way other than described herein in order to avoid personal injury or property damage.
- User should comply with the laws and regulations of the corresponding countries and regions where the equipment is located (used), abide by professional ethics, pay attention to safety obligations, and strictly prohibit the use of our products or equipment for any illegal purposes. Our company will not be responsible for any violators’ legal liability under any circumstances.
NOTICE
Notice (United States Of America)
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to wprovide reasonable protection against harmful interference in a
residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: (1) Reorient or
relocate the receiving antenna. (2) Increase the separation between the
equipment and receiver. (3) Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected. (4) Consult the
dealer or an experienced radio/TV technician for help.
FCC Radio Frequency Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The
device can be used in fixed/mobile exposure condition. The min separation
distance is 20cm.
Notice: Shielded cables All connections to other computing devices must
be made using shielded cables to maintain compliance with FCC regulations.
Frequency bands and power are as below:
Function | Bands | Operation Frequency | Max.Power |
---|---|---|---|
WI-F1 | 2.4GHz | 2412-2472MHZ | EIRP 19.10 dBm |
Bluetooth | 2.4GHz | 2402-2480 MHz | EIRP 8.0 dBm |
Your product is designed and manufactured with high quality materials and
components, which can be recycled and reused.
This symbol means the product must not be discarded as household waste, and
should be delivered to an appropriate collection facility for recycling.
Proper disposal and recycling helps protect natural resources, human health
and the environment. For more information on disposal and recycling of this
product, contact your local municipality, disposal service, or the shop where
you bought this product.
Trademarks
The Bluetooth® word mark and logos are registered trademarks owned by the
Bluetooth SIG, Inc. and any use of such marks by Anker Innovations Limited is
under license. Other trademarks and trade names are those of their respective
owners.
References
- AnkerMake | Setting the Pace in High-Speed 3D Printing - Ankermake US
- AnkerMake | Setting the Pace in High-Speed 3D Printing - Ankermake US
- AnkerMake Studio - Ankermake US
- Anker (アンカー) Japan 公式オンラインストア – Anker Japan 公式オンラインストア
- AnkerMake 3D Printers - Pioneering High-Speed 3D Printing - Ankermake US
- AnkerMake 3D Printers - Pioneering High-Speed 3D Printing - Ankermake US
- AnkerMake | Setting the Pace in High-Speed 3D Printing - Ankermake US
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>