OSI-ALM-MINI-W-6 WiFi Mini Alarm System User Guide

OSI-ALM-MINI-W-6- WiFi- Mini -Alarm -System

FEATURES

• Simplistic design, excellent user operation experience
• Built-in powerful 32-bit Cortex-M3 kernel CPU controlling unit
• Wi-Fi alarm notification, local alarm and APP Push for reliable alarm performance
• Up to 4 remote controls and 50 Wireless detectors can be learned
• Multiple alarm types including: door, living room, SOS (PANIC), bedroom, windows, balcony, perimeter,(smoke, gas, CO2, Water leak alarm type not applicable to this system)
• Low Battery Power alert for the wireless sensors
• Multiple alarm modes supported: ARM, STAY ARM, 24h Active, Doorbell, etc.
• Voice Prompt for operation

TERMINOLOGY

Burglary Protection
The OSI Mini Alarm System provides two modes of burglary protection:
Stay ARM:This mode protects the permieter only (Door/Window Sensors are the only sensors which are active), allowing you to freely move inside the premises. You would Arm the system as Stay Arm when you are staying at home or in most cases before you go to bed.
ARM: This mode protects the entire system (Both Door Sensors & Motion Sensors are Active). You would arm the system as ARM when you are leaving the house and nobody is home. Both modes provide an entry delay time which allows you to re-enter the premises without setting off an alarm.

Zone
Your OSI Mini Alarm Sensors have been assigned to various “zones’: For example, the Door/Window sensor on your entry/exit door may have been assigned to zone 01, and the Diir/Window sensor on the windows in the master bedroom to zone 02, and so on. These numbers appear on the display in your notifications when the alarm or trouble condition occurs.

Exit/Entry Delays
The OSI Mini Alarm has been programmed with delay times that allow you to exit the premises after arming, and to disarm the system upon entry, before an alarm occures. If you leave the premises too late when exiting, or disarm too late when arriving home, it will cause a false alarm. If an alarm occurs, you should disarm the system immediately

Alarms
When an alarm occurs, the built-in siren will sound until the system is disarmed or the until the siren timeout occures, and push notification sent to the Smart Life app on your smartphone/tablet displaying the triggered sensor. To stop the alarm siren, you simply disarm the system using either the included remotes, Smart Life app or Voice Control through Amazon Alexa or Google Home.

OSI HUB FRONT VIEW

OSI HUB BACK VIEW

OSI HUB SIDE VIEW

Note: The power plug may be different as above diagrams based on different countries standards.

FUNCTION BUTTON

To Clear your Wi-Fi Network settings so you can connect it to a different Wi-fi Network
If there’s power failure or poor WiFi network, and it was locked in ARM status when there’s no power or when you unplug it or if you try to connect it to a different WiFi, it doesn’t work then do the following:
Simply press (short) the function button Stimes within 10 seconds after power on, to unlock the previous WiFi.

How to put the Mini Hub in PAIRING MODE to connect to the Smart Life App
To connect the Mini Alarm System to your Wi-Fi Network Smart Mode: Long press the function button for 5 seconds within 10 seconds after power cycle (plugging in hub into the electrical outlet). (Green LED flashes quickly).
To connect the Mini Alarm System to your Wi-Fi Network AP (Access Point) Mode: after following the step above (while in Wi-Fi Network Smart Mode), press the function button once again, and the system will enter Wi-Fi AP Mode (Green LED flashes slowly). *This mode recommended. the Mini Alarm is now in Pairing mode. After 1 minute it will exit pairing mode.

LED STATUS INDICATOR

• DISARMED: Solid Green
• AWAY ARM: Solid Yellow
• AWAY ARM (Delay): Yellow Flashes Slowly
• HOME ARM: Yellow Blinks Twice Every 6 Seconds
• WI-Fl Network Smart Mode: Green LED Flashes Quickly
• WI-Fl Network Ap (Access Point) Mode: Green LED Flashes Slowly
• ALARM TRIGGERED(Entry Delay): RED Flashes Slowly
• ALARM SENSOR/SOS TRIGGERED: RED Flashes Quickly

CONNECTING THE OSI MINI ALARM TO THE SMART LIFE APP

When the Smart Life app is used for the first time, you need to connect the Mini Alarm System and configure your wi-fi settings. Also, before starting these following steps you should have already installed the Smart Life app on your smartphone/tablet and created your Smart Life account. Please have the OSI WIFI MINI HUB with you and be near an electrical outlet.

Smart Life on ANDROID

ANDROID: CONNECTING SMART LIFE APP
Connecting your OSI MINI Alarm to Smart Life app using “AP Mode” (Access Point) (recommended)

1. Step 1: Open Smart Life app and select the “plus” icon at the top right corner
2. Step 2: Select “Add Device”
3. Step 3: Select “Sensors” on left panel, then select “Alarm (wi-fi)”
4. Step 4: Select your 2.4 Ghz Wi-Fi Network and enter your password
5. Step 5: Press “Next” to Confirm Mini Alarm Hub is in pairing mode (LED is Flashing Green Slowly)
6. Step 6: Select “Blink Slowly”.
7. Step 7: Select “Go to Connect”
8. Step 8: Select “Smartlife-XXX”. This is the WI-Fi Access Point located within the OSI Mini Alarm
9. Step 9: On the Wi-FI screen select “Smartlife-XXXX” (XXXX will be 4 unique numbers and letters) under “MY NETWORKS”
10. Step 10: Select “Connect only this time”
11. Step 11: Once selected RETURN to the Smart Life app where you will see this screen showing “Adding device”.
12. Step 12: You should see “added Successfully” Smart Life App is now connected to the OSI Wi-Fi Mini Alarm

Smart Life on 10S (IPHONE)

10S: CONNECTING SMART LIFE APP (IPHONE/IPAD)
Connecting your OSI MINI Alarm to Smart Life app using “AP Mode” (Access Point) (recommended)

1. Step 1: Open Smart Life app and select the “plus” icon at the top right corner
2. Step 2: Select “Add Device”
3. Step 3: Select “Sensors” on left panel, then select “Alarm (wi-fi)”
4. Step 4: Select your 2.4 Ghz Wi-Fi Network and enter your password
5. Step 5: Press “Next” to Conti rm Mini Alarm Hub is in pairing mode (LED is Flashing Green Slowly)
6. Step 6: Select “Blink Slowly”.
7. Step 7: Select “Go to Connect”
8. Step 8: Select “Smartlife-XXX”. This is the WI-Fi Access Point located within the OSI Mini Alarm
9. Step 9: On the Wi-FI screen select “Smartlife-XXXX” (XXXX will be 4 unique numbers and letters) under “MY NETWORKS”
10. Step 10: Select “Connect only this time”
11. Step 11: Once selected RETURN to the Smart Life app where you will see this screen showing “Adding device”.
12. Step 12: You should see “added Successfully” Smart Life App is now connected to the OSI Wi-Fi Mini Alarm

MAIN APP INTERFACE

LOG HISTORY

ACCESSORIES

SETTINGS

REMOTE CONTROL

Button Features Description:

• [ a ] Away ARM
• [ Q ] HomeARM
• [ r:::r’ ] Disarm
• [SOS] SOS

Alarm
When the alarm has been triggered, the alarm will push a notification to your Smart Life app on your smartphone/tablet and the siren will sound at the same time. To turn off the alarm, press the disarm button in the Smart Life app or on your remote control.
To view alarm Log: open the Smart Life app and go into alarm device and select History Records. Here you will see a log of every time the Sensor has triggered an alarm, SOS (PANIC) button has been pressed, AC Power Recover, Low Battery, or when you arm or disarm the device.

SPECIFICATIONS

• Input current: AC l00V-AC 240V 50Hz/60Hz
• Standby power: <1.0W
• Operation power: <SW
• Wireless frequency: 433MHz
• Wireless code: eV1527
• WiFi system : IEEE802.11b/g/n standard, 1-14@2.4GHz
• Operation temperature: -1o~ss0c
• Relative humidity : <80% (none frozen)
• Product size: diameter79mm, height 46mm(include the metal plug, main body 30mm)

Unlimited Users

Thank you for your purchase!
We’re happy you chose our OSI Smart DIV product and appreciate your business. We’re constantly striving to provide the best experience for our customers. If you have quesitons or need help with your product please create a Support Ticket at www.osigodirect.com/contact (allow up to 1 business day for reply) and let us do our best to help you! OSI Go Direct Team

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>