MUDBUSTERS 91009 Fender Flares Instructions

: June 3, 2024
: MUDBUSTERS

Table of Contents

IMPORTANT
Unboxing
utvmudbusters.com or email us via
Installation Instructions
Hardware Included
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MUDBUSTERS 91009 Fender Flares Instructions

www.mud-busters.com
Email us for digital instructions: Mudbusters@gracemfg.com

Thank you for purchasing MudBuster’s fender flares for the Honda Pioneer 1000-3! We manufacture the bestselling fender flare kits for UTVs and side by sides! All MudBusters products are made in the USA, and these fender flares are manufactured from high-quality American made material. Your new extended fenders are designed to deflect debris and reduce the amount of mud that typically gets thrown from the tires into unwanted areas. They can withstand a lot of abuse, but they are not designed for crash protection, absorbing impacts, rollovers, or uprooting trees. If you have an accident or if you happen to damage your fenders, order discounted replacement fenders by phone (for existing customers only). Unlike other manufacturers, you do not have to buy a complete set if you damage just one fender.

IMPORTANT

Some of the images in the instructions below may differ from the actual product. In our continual effort to increase customer satisfaction, we may change the style, material, and/or hardware to serve you better. If your fenders get slightly distorted while in transit, apply pressure to the distorted areas to straighten them out before installation. Use caution when drilling into the factory panels of your vehicle. Make sure that you do not penetrate the surrounding parts or the chassis (unless instructed). Self- tapping screws and push rivets are included as an effective and easy way to fasten the fender flares to your machine. However, you can use other methods of securing our extended fenders to your vehicle as well (i.e., rivets, misc. hardware, etc.). Remember, it may be helpful to have a friend assist you with the installation.

Unboxing

Carefully open your package from the box’s top (or bottom) by removing the staples with a flat-head screwdriver or plyers. Slide the fenders out of the box and make sure that any staples do not scratch your fenders. MudBusters are formed to fit your machine but shipped in a narrow box. You may find it necessary to apply pressure and re-bend some of your fenders for a better fit. Don’t worry, they’re very durable and will not break from re-shaping them!
Note: Using a larger drill bit may allow the fender to come off when riding! The rivets need to be a tight fit to secure the fender flare to the fender. We recommend a 21/64″ drill bit.
Note: Max coverage set shown. Smaller sets (Mud-Lite, or Race-Lite) may have less hardware in the front of the front fender or the lower front of the rear fender than pictured. In these cases, it may be helpful to use the rear mounting locations first for installation ease.

WARNING
This pro1duct can 1expos1e you to chemicals, including phthalates which are know1n to the State of California to cause cancer or birth defects or other reproductive harm. For more info, go to www.p6,5Warnings.ca.gov

Thank you for your business!
Please send us pictures and/or videos of your vehicle with MudBusters installed to our Facebook page https://www.facebook.com/UTVMudbusters/

utvmudbusters.com or email us via

mudbusters@gracemfg.com
We may feature your ride on our website, social media, Amazon and/or eBay!
For technical assistance or product inquiries, please call us at:
1-844-MUD-FLAPS or 844-683-3527
Hours: Mon-Fri 8-4 MST

Installation Instructions

Upper Rear Fender Flare Installation

**Lower Rear Fender Flare Installation

**

Short Front Fender Flare Installation

Note: The front fenders included in this kit can be installed on your vehicle with or without Honda’s front over- fenders, but they are only adjustable when installed with over-fenders.

Once the fender is in position, use the holes on the fender as a guide to drill through the factory fenders. Using a 5/16 drill bit and a cordless drill, drill out the holes and insert a plastic rivet into each hole. If you wish to take off the fenders in the future, the plastic rivets used for the installation can be inserted to plug the holes.