Shenzhen Luokeweilai Trading 258Z Wireless Controller User Guide

Shenzhen Luokeweilai Trading 258Z Wireless Controller User Guide

Key Layout

1. – button
2. Screenshot button
3. Home button HOME
4. +button
5. Left stick
6. Directional pad
7. ¥ button
8. X button
9. A button
10. B button
11. Right stick
12. Turbo
13. R button
14. RZ button
15. L button
16. LZ button
17. Type-C charging interface

Specifications

1. Size: 6.064.372.32in
2. Weight: 6.526+0.350z
3. Material: new ABS environmentally friendly material
4. Connection method: Bluetooth
5. Vibration: dual motor, powerful vibration mode
6. Built-in six-axis gyroscope and acceleration function for better game experience
7. Support continuous burst and burst clearance function

First Use

USB Pairing

Wireless Pairing

Please ensure that the host is powered on and has been upgraded to the latest version before using this product.

1. Press the Switch power button to start the host

2. After booting up, do the following: first step enter the “Handle Settings – Change Grip / Order” page, hold the Y button then press and hold Home button at the same time for more than two seconds.

3. The 4 LED lights will continue to flash. After the successfully connected, the LED lights indicate the corresponding game player.

Connection Problem

If the controller can not connect with Switch Console, please resolve with the following methods.

1. Fully charged via USB cable if power low then attempt to connect.

2. Try to connect with Switch Console via USB cable. As pictures shown (Setting – Controllers and Sensors – Pro Controller Wired Communication), only works when enable Pro Controller Wired Communication Mode.

3. Clear the Switch Console connection cache if 1&2 methods can not work out, as pictures shown(Setting – System – Formatting Options – Reset Cache). Too much Bluetooth data may cause connection error.in order to avoid this situation, clearing the Bluetooth data before the controller be connected is necessary.

4. It still can not connect after trying the above methods, you can reset by pressing the reset button on the back of the controller.

Use again

1. Press the Home button for more than 1 second to wake up the handle.
2. Switch host enters the connection mode automatically in power on state, after successfully connected, the corresponding LED light on the handle will remain bright.
   It will be in sleep mode automatically after unsuccessful connection for 10 seconds; other buttons have no wake-up function

Driver upgrade

We support computer connection with USB to upgrade the program of our products, so as to support the latest upgrade of SWITCH. If you still can not use the controller after upgrade to the latest version, please contact us with email (support@binbok.com) on visit the home page (www.binbok.com) to download the driver package to upgrade.

Automatic sleep

1. The controller automatically sleeps when the host screen is off.
2. The controller automatically sleeps without pressing any button in 5 minutes.(sensor does not move).
3. Bluetooth mode, press the HOME button for 5 seconds, disconnect from the host.

Charging indication

1. When the handle is off, LED1-LED4 flash slowly when the power is charging, and the LED is off when fully charged.
2. Battery low voltage alarm system: current indicator flashes (quickly flashing)
3. When the pairing indication conflicts with the charging low power indicator, the pairing indicates a concern.

Low voltage alarm

1. If the lithium battery voltage is lower than 3.55V+0.1V, the current channel tight flashes quickly and indicate low voltage.
2. If the lithium battery voltage is lower than 3.45V±0.1V, it will automatically sleep.

Reset key function

When there are some unsolvable faults in the controller, you can try to press and hold the reset button on the back of the controller for more than 5 seconds. At this time, the handle is powered off and reset, and you need to reconnect according to the method of connecting the controller for the first time.

Turbo function

1. Made A: Hold the button to burst
   Hold the T button, press A/B/X/Y/L/R/ZL/ZR at the same time to set Turbo into mode A.

2. Mode B: Automatic Turbo
   Set Turbo into mode A, then hold the T button again, press AVB/X/Y/LIR/ZL/ZR at the same time to set Turbo into mode B.

3. Switch the Turbo modes:
   Mode A: Hold the button to burst Mode B: Automatic Turbo>Turbo mode off,

e.g. Press T button and A button at the same time to turn on the turbo function of A button. Press A button again and press T button at the same time to turn the turbo mode into Automatic mode. Then press A button and T button again at the same time to turn off the Turbo function.

Turbo function have LED indication

TURBO speed adjustment method

1. Press “T” + “Up Arrow’ to decreases TURBO speed;
2. Press “T” + “Down Arrow” to increases TURBO speed.

During the burst, the mode light flashes at the corresponding speed, flashes slowly, flashes at medium speed, and flashes quickly.

The speeds of these three gears are:

• A. continuous burst 5 times per second (1st gear);
• B. continuous burst 12 times per second (2th gear);
• C. continuous burst 20 times per second (3th gear)

Calibrate control sticks

1. Press the Home button to return to the host interface and select system settings

2. Select “Controllers and Sensors’>”Calibrate Control Sticks”, Press A to enter the following interface

3. Press A to enter the following interface

4. Press the stick(left/right) to enter the calibration interface then calibrate the stick

5. Press the X button to adjust the interface, and continue the next step according to the host indication

Axis calibration

(recommended to do this after the first connection to ensure the normal use of the shaft)

• A. In the shutdown state, press “2 and “B” at the same time, press the home button at last, then LED1, LED2 and LED3, LED4 will flash alternately and enter debugging mode.

• B. Place the handle on the desktop or other flat position. Press “+” button, the host will calibrate automatically. After the calibration is completed, the handle will be automatically connected to the host.

• C. After completed, please re-enter the handle debugging interface to test whether the handle is OK.

• D. The host confirms automatically when the below interface appears, it indicates that the calibration has been completed and can be used normally.

Motor vibration adjustment

1. Hold the R, L, ZR, ZL buttons at the same time for 2 seconds to adjust the vibration level.
   The handle has 3 levels vibration adjustable. The vibration function is divided into 3 levels: 100%, 75%, 30% (default is 75%). After the adjustment is successful, the motor in this gear will vibrate for 0.5 seconds, and the LED indicators will indicate the vibration level when you set it.

Button

1. 1f controller button fails or does not work, please perform the following operation test: Setting – Controllers and Sensors-Test Input Devices (If there is a problem with the button in the test experiment, contact customer service for a replacement.)
2. When left & right control stick operation deviations, perform control stick calibration: Setting – Controllers and Sensors – Calibrate Control Sticks
3. please calibrate the controller if you meet motion sensor problem: Setting – Controllers and Sensors – Calibrate Motion Controls – Calibrate Controllers (the controller must be placed horizontally when calibrating)

Warning

1. Do not expose the controller to high temperature, high humidity or direct sunshine.
2. Do not allow liquid or small particles to enter the controller.
3. Do not put any heavy object on the controller.
4. Do not disassemble the controller.
5. Do not twist or pull the cable too strongly.
6. Do not throw, drop, or apply strong shock to the controller.

support@binbok.com
support.jp@binbok.com

@BINBOKOfficial
@BINBOK_JP

@BINBOK
@BINBOK Japan

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>