Roccat KONE PRO User Manual and Driver

: June 5, 2024
: ROCCAT

Table of Contents

Roccat KONE PRO Mouse
PACKAGE CONTAINS
DEFAULT BUTTON ASSIGNMENT
INSTRUCTIONS
Disposal information
Technical support
TECHNICAL FACTS
DRIVERLESS SETUP
FCC CAUTION:
Join the community
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Roccat KONE PRO Mouse

QUICK START GUIDE

Download Driver
ROCCAT® Talk® FX

PACKAGE CONTAINS

Please remove the blue protection film from the mouse feet before use

DEFAULT BUTTON ASSIGNMENT

(no driver installed)

STANDARD

1 = Left mouse button
2 = Right mouse button
3 = Universal scroll
4 = Scroll up
5 = Scroll down
6 = IE Forward
7 = IE Backward
8 = Profile cycle button

BUTTON ASSIGNMENT

INSTRUCTIONS

Plug the USB connector into any free USB port on your PC or laptop.
Navigate to www.roccat.com/downloads and download the latest driver.
Complete the installation to get access to all software features and setup.

Disposal information

The crossed-out wheelie-bin symbol means that you must not dispose of this product toge-ther with unsorted household waste. As electrical devices can contain harmful substances which may cause environmental damage or harm to your health if not disposed of correctly, please dispose of these products separately. As the end user, you are required by law to dispose of used electrical equipment at an official recycling point. For information about local recycling points, contact your local authority, civic amenity site or the business where you purchased this product. By disposing of electrical products at an official recycling point, you are doing your bit to ensure equipment is recycled correctly and professionally, and our environment is protected.

When purchasing a new product, the retailer will let you hand in old products and dispose of them free of charge provided the product you are handing in is of a similar type and has the same functions as the product you are purchasing. You can hand in small used electrical and electronic equipment (measuring no longer than 25 cm on any one side) for free and with no obligation to purchase a similar product at electrical and electronic retail outlets with sales areas larger than 400m² or at nearby recycling points designated by the retail outlet.

Wherever possible, remove any batteries before disposing of the device.

Under law, as a user you face the risk of penalties if you dispose of devices and batteries illegally.

Technical support

Having technical problems with this product? Get in touch with our Support team – the quickest way is via our website:
www.roccat.com/support

Please keep this information for later reference.

TECHNICAL FACTS

TECH SPECS KONE PRO

ROCCAT ® Owl-Eye 19K dpi optical sensor
(based on PixArt PAW3370)
400 IPS (10.2m/s) maximum speed
50g maximum acceleration
(stop to maximum speed in 0.03s required to reach limit)
Default DPI steps: 400, 800 (default), 1200, 1600, 3200 1.8m Phantom Flex™ cable length
1000Hz polling rate
Lift-off distance: 1mm, 2mm and surface calibration ARM32 M0+ MCU
On-board memory
ROCCAT ® Titan Switch Optical, 100 million click life-cycle 66g weight

SYSTEM REQUIREMENTS

Windows® 7, 8 and 10 (software support)
USB 2.0 (or higher)
Internet connection (for driver software)

Should you need assistance …
Our support team is ready to help you with any technical questions. Just send an e-mail to support@roccat.com or visit our website at:
WWW.ROCCAT.COM/SUPPORT

DRIVERLESS SETUP

Press the profile button in combination with the left mouse button for three seconds to enter config mode. The mouse will blink in the color of the active profile. To exit config mode, press the profile button in combination with the left mouse button for three seconds once more.

Scroll up/scroll down: Change DPI level from 5 available presets. LEDs will fade into one of the colors listed below to reflect the chosen DPI preset.

400 DPI – red
800 DPI – green
1200 DPI – cyan
1600 – blue
3200 – pink

Forward side button/backward side button: Change polling rate. The right mouse button will blink in one of the colors listed below to reflect the chosen polling rate.

125Hz – blue
250Hz – green
500Hz – yellow
1000Hz – white (default)

Wheel click: Swap between 1mm and 2mm lift-off distance. The left mouse button will blink in one of the co-lors listed below to reflect the chosen lift-off distance.

1mm – red
2mm – green

While holding the left mouse button, press forward side button/backward side button: Change LED brightness in steps of 10%.

While holding the right mouse button, press forward side button/backward side button: Change between Static, Wave, Heartbeat, Breathing or Blinking RGB modes. The effect is immediately shown on the mouse.

While holding the left or right mouse buttons and wheel up/down: Change the color of the LEDs corresponding to the button held from 16 presets. When both are held at the same time it changes both at once. Changes are immediately shown on the mouse.

FCC CAUTION:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation

GENERAL SAFETY GUIDELINES AND INTENDED USE

Do not open or modify the product.
Not approved changes or modifications may void the operation authority and/or warranty.
In case of trouble or doubt, contact us immediately.
Keep the product away from fire/water/humidity/temperature extremes.
Only use as intended with a compliant PC and connector part.
Improper or incorrect use of the product or use of the product for purposes not recommended by the manufacturer void the liability and/or warranty.
Don‘t look into the light beam on bottom of the mouse.

Hereby, Voyetra Turtle Beach Corp. declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/30/EU.

The full Declaration of Conformity can be requested via following:
Company: Voyetra Turtle Beach, Inc.
Address: 44 South Broadway, 4th Floor, White Plains NY 10601, USA
E-Mail: support@roccat.com

VOYETRA TURTLE BEACH, INC. | 44 SOUTH BROADWAY, 4TH FLOOR, WHITE PLAINS NY 10601, USA

© 2022 Voyetra Turtle Beach, Inc. All rights reserved. Any product names mentioned in this manual may be trademarks or registered trademarks and are the property of their respective owners. Information contained herein is subject to change without notice. Voyetra Turtle Beach, Inc. shall not be made liable for any errors that may appear in this manual. This publication or parts of it may not be reproduced without the express consent of the publisher.

ROCCAT® is a Turtle Beach Brand.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure
and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
BSMI https://www.roccat-neon.com/Bsmi