cybex UN R44 Pallas S-Fix Car Seat User Guide

Cybex-UN-R44-Pallas-S-Fix-Car-Seat-11

INSTALLATION

IMPORTANT INFORMATION

• Without the approval of the Type Approval Authority, the car seat may not be modified or added to in any way.
• In order to keep your child properly protected, it is absolutely essential that you use the car seat as described in this user guide.
• This car seat may only be installed on vehicle seats which are approved for the use of child restraint systems according to the vehicle manual.
• Only suitable for vehicle seats with automatic three-point belts approved in accordance with UN Regulation No.16 or a comparable standard.
• Do not use any load bearing contact points other than those described in the user guide and marked on the child restraint.
• The full surface of the backrest of the car seat must make contact with the backrest of the vehicle.
• The shoulder belt must run upwards and back at a recline. It must never run forward to the upper belt point in your vehicle.
• The vehicle belt buckle must never cross the belt guide of the seat. If the belt whip is too long, the car seat is not suitable for use in this position in the vehicle. In case of doubt please contact the child restraint manufacturer.
• The three-point vehicle belt must only be passed through the designated routings. The belt routings are described in detail in this user guide and are marked in red on the car seat.
• The lap belt must run as low as possible across your child’s groin to have optimum effect in the event of an accident.
• Before each use make sure that the automatic three-point vehicle belt is correctly adjusted and fits tightly to the child’s body. Never twist the belt!
• Only an optimally adjusted headrest can offer your child maximum protection and comfort while ensuring that the shoulder belt can be fitted smoothly.
• For usage in Group 1 the impact shield must be used.
• The car seat must always be secured correctly with the automatic three-point vehicle belt in the vehicle even when not in use.
• Always ensure that the car seat is never jammed when closing the vehicle door or adjusting the back seat.
• For the car seat to provide the best possible protection, always use the Linear Side-impact Protection (L.S.P.) to the nearest door side.
• If using the car seat on the middle seat of the vehicle’s backbench, the Linear Side-impact Protection (L.S.P.) must never be folded out.
• The car seat has also been tested and approved for use without the Linear Side-impact Protection (L.S.P.) folded out.
• Luggage or any other objects present in the vehicle must always be firmly secured. Otherwise, they may be thrown within the vehicle, which could cause fatal injuries.
• The car seat must never be used without the seat cover. Ensure that only an original CYBEX seat cover is used, as the cover is a key element of the seat’s function.
• Never leave your child unattended in the vehicle.
• Parts of this child restraint system can heat up when exposed to direct sunlight and could potentially burn your child’s skin. Protect your child and the car seat from direct sun exposure.
• An accident may cause damage to the car seat that is not identifiable with the naked eye. Please replace the car seat after an accident. In case of doubt, please consult your dealer or the manufacturer.
• Do not use this car seat for more than 11 years. The car seat is exposed to high stress during its product life span, which leads to changes in the quality of the material with increasing age.
• The plastic parts can be cleaned with a mild cleaning agent and warm water. Never use harsh cleaning agents or bleaches!
• On some vehicle seats made of sensitive materials, the use of car seats may leave marks and/or cause discolouration. To prevent this, you can place a blanket or towel or similar underneath the car seat to protect the vehicle seat.

PRODUCT PARTS

1. User guide storage compartment
2. Backrest
3. Adjustable headrest
4. Headrest height adjuster
5. Booster
6. Impact shield
7. Belt guide – Group 1
8. Lap belt guide – Group 2/3
9. Shoulder belt guide
10. Linear Side-impact Protection (L.S.P)
11. ISOFIX-Connect-locking arms
12. ISOFIX-Connect-adjustment handle
13. ISOFIX-Connect-release button
14. ISOFIX-Connect-safety indicator
15. ISOFIX-anchorage points
16. L.S.P.-operating button
17. Central adjustment button of the impact shield
18. Position adjustment button
19. Base
20. Release buttons of the base
21. Snap dips
22. Lever for reclining headrest

THE CORRECT POSITION IN THE VEHICLE

The car seat with retracted ISOFIX-Connect-locking arms (k) can be used on all vehicle seats with automatic three-point safety belts approved in the vehicle manual for “universal” use.
A “semi-universal” certification is given to restraint systems that are connected to the vehicle through ISOFIX-Connect-locking arms (k). For this reason, ISOFIX-Connect can only be used in certain vehicles. Refer to the enclosed vehicle type list for approved vehicles. You can obtain the most up- to-date version from www.cybex-online.com.
In exceptional cases, the car seat may also be used on the front passenger seat. Always comply with the recommendations of the vehicle manufacturer.

INSTALLING THE CAR SEAT IN THE VEHICLE

1. Always ensure that…
2. the backrests in the vehicle are locked in their upright position.
3. when installing the car seat on the front passenger seat, adjust the vehicle seat as far back as possible without affecting the belt routing.
4. Use the ISOFIX-Connect-adjustment handle (l) under the booster (e) and pull the two ISOFIX-Connect-locking arms (k) to their furthest extent.
5. Now twist the ISOFIX-Connect-locking arms (k) 180° so that they are facing the direction of the ISOFIX-anchorage points (o).
6. Place the car seat on the appropriate seat in the vehicle.
7. Push the two locking arms (k) into the ISOFIX-anchorage points (o) until these lock into place with an audible “CLICK”.
8. Use the ISOFIX-Connect-adjustment handle (l) and push the car seat against the vehicle seat.
9. Ensure that the entire surface of the backrest of the car seat (b) is placed against the backrest of the vehicle seat.
10. If the headrest of the vehicle is in the way, pull it upwards to its furthest extent or remove it completely (except in rear-facing vehicle seats).
11. Ensure the car seat is secure by trying to pull it out of the ISOFIX-anchorage points (o). The green safety indicators (n) must be clearly visible on both sides of the car seat.
12. In case the car seat is used without ISOFIX-Connect, it can be stored away on the bottom of the car seat.
13.  To activate the Linear Side-impact Protection (L.S.P.) (j) press the L.S.P.-operating button (p).
14. By using ISOFIX-Connect, a connection to the vehicle is created which increases your child’s safety. Your child still needs to be secured with the three-point belt of the vehicle and the impact shield for Group 1.
15. The car seat can also be used with the Linear Side-impact Protection(L.S.P.) folded in if there is not enough space in the vehicle or if the Linear Side-impact Protection (L.S.P.) is in conflict with the vehicle door.

REMOVING THE CAR SEAT FROM THE VEHICLE

Perform the installation steps in the reverse order.

1. Unlock the ISOFIX-Connect-locking arms (k) on both sides by pushing the release buttons (m) and pulling them back simultaneously.
2. Pull the car seat away from the ISOFIX-anchorage points (o).
3. Remove the car seat and store the ISOFIX-Connect in reverse order to installation.

ADJUSTING THE HEADREST
The headrest (c) can be adjusted by using the headrest height adjuster (d)at the back of the headrest (c). Adjust the headrest (c) so that max. 2 cm (approx. 2 finger’s width) remain between the child’s shoulder and the headrest (c).

The height of the headrest can still be adjusted while the car seat is installed in the vehicle.

RECLINING HEADREST

The reclining headrest (c) helps to prevent the child’s head from dangerously tipping forward during sleep. It can be set to one of 2 positions. Push the reclining headrest (c) forward until the desired position is reached. To return it to the original position, the lever (v) must be operated and the headrest pulled back.

The child’s head should always be in contact with the reclining headrest.

CORRECT INSTALLATION MODE

SECURING THE CHILD WITH IMPACT SHIELD – GROUP 1 (9–18 KG)

1. Insert the impact shield (f). The side flaps of the impact shield (f) fit exactly between the arm rests and seating surface of the booster. Push the central adjustment button (q) and adapt the impact shield to your child.
2. Pull out the entire length of the vehicle seat belt.
3. Place the lap belt over the designated red belt routing on the impact shield (g).
4. Lock the vehicle seat belt into the belt buckle. It must lock in place with an audible “CLICK”.
5. Tighten the lap belt by pulling the shoulder belt backwards.
6. Feed the shoulder belt in parallel with the lap belt back into  the belt routing (g) and pull the shoulder belt tight. Ensure that both parts of the belt cover the entire width of the impact shield (f) in the belt routing (g).
7. Feed the shoulder belt tightly through the belt routing of the impact shield (g) until it is clamped inside the belt guide.
8. Put the shoulder belt between headrest (c) and backrest (b). The shoulder belt does not need to be guided through the shoulder belt guide (i).

ADJUSTING THE LYING POSITION (9-18 KG)

1. To put the seat in the lying position, press the position adjustment button (r).
2. To return the seat from the lying position to the sitting position, press the position adjustment button (r) again and guide the seat upwards with light pressure against the booster (e).

The lying position is only available for group 1 (9-18 kg).

SWITCH FROM GROUP 1 TO GROUP 2/3

1. Remove the impact shield (f), as soon as your child weighs 18 kg.
2. Switching from group 1 to group 2/3 is not permitted if your child weighs less than 15 kg. Keep the impact shield in a safe and secure place.
3. Press the two release buttons of the base (t) on the underside of the booster (e) and pull it away from the base (s) until there is some resistance.
4. Press the position adjustment button (r) and pull the seat away from the base (s) completely.
5. Operate the ISOFIX-Connect-adjustment handle (l) and pull the two ISOFIX-Connect-locking arms (k) out.
6. Keep the ISOFIX-Connect-adjustment handle (l) held and release the two snap clips (u) on the underside of the booster (e), one after the other and pull the ISOFIX-Connect looking arms (k) out of the base. If necessary, use a screwdriver.
7. Push the ISOFIX-Connect-locking arms (k) into the designated openings on the underside of the booster (e) until there is some resistance.
8. Operate the position adjustment button (r) on the underside and push the ISOFIX-Connect-locking arms (k) as far in as possible.

Note:  the minimum drop height of the ISOFIX-Connect-locking arms.

Ensure that the locking arms (k) are installed the right way around and that the teeth of the locking arms are up.
When reassembling the seat, proceed in precisely the reverse order. Use the instructions to check beforehand if all parts are present.

SECURING THE CHILD WITHOUT IMPACT SHIELD – GROUP 2/3 (15–36 KG)

1. Route the vehicle seat belt around your child and insert the belt tongue into the belt buckle. It must lock into place with an audible “CLICK”.
2. Place the lap belt in the red-colored lap belt guides (h) of the car seat.
3. Pull the shoulder belt to tighten the lap belt.
4. On the side of the car seat next to the belt buckle, the shoulder belt and the lap belt must be inserted together in the lap belt guide (h).
5. Feed the shoulder belt through the shoulder belt guide (i) until it is inside the belt guide.
6. Ensure that the shoulder belt runs across your child’s clavicle and does not touch your child’s neck. If necessary, adjust the height of the headrest (c) to change the position of the belt.

REMOVING AND REATTACHING THE SEAT COVER
The cover of the car seat consists of 5 parts (Headrest flap, headrest, backrest, booster and impact shield). These are held in position at several places by press studs. Once all studs have been released, the single parts of the cover can be removed. In order to put the covers back on the car seat, follow the removal instructions in the reverse order.

The cover may only be washed at 30 °C with a delicate wash program otherwise it may result in discoloration of the cover fabric. Please wash the cover separately from other laundry and do not dry in the dryer or in direct sunlight!

MANUFACTURER’S WARRANTY AND DISPOSAL REGULATIONS

CYBEX GmbH (Riedingerstr. 18, 95448 Bayreuth, Germany) gives you
3 years warranty on this product. The warranty is valid in the country, where this product was initially sold by a retailer to a customer. The contents of the guarantee and all essential information required for the assertion of the guarantee can be found on our homepage go.cybex-online.com/manufacturer-warranty-car-seats. If a warranty is shown in the article description, your legal rights against us for defects remain unaffected. Please observe the waste disposal regulations in your country.

References

• CYBEX Online Shop | Child Car Seats, Strollers, Baby Carriers and Furniture from CYBEX

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>