LOKITHOR JA301 Jump Starter Power Bank Air Compressor Instruction Manual

June 5, 2024
LOKITHOR

Lokithor Start Your Life
JA301

website: www.lokithorshop.com

Thank you for purchasing products of LOKITHOR, please read this manual carefully before use, and properly save it for future reference

Safety Instructions

Please read the following instructions carefully before using the LOKITHOR multi-function vehicle emergency starter (hereinafter referred to as the jump starter):

  1. Please strictly follow the instruction manual to operate. if used improperly, or against the instructions, it may cause a serious safety incident.
  2. Only for starting 12V engine and can not start vehicles exceeding specified displacement or
  3. Under the forced start mode, part of the security protection mechanism is invalid, so please use with caution, and check the instruction manual before usage;
  4. If you start to pump up your tires without setting a target tire pressure value, the air inflator will not automatically stop pumping and instead, you will need to manually stop There’s a risk of over-inflated tires or a blowout condition if the tire pressure is not kept under observation in real-time;
  5. The air inflator generates heat when used, especially at the air nozzle. Do not touch the air inflator immediately after pumping, and we suggest you wear gloves to protect yourself against
  6. In order to prolong the life of the battery, please charge the device after purchase, and charge and discharge the device every three months to ensure that it is in good condition for the next use.
  7. Do not use a jump starter that has been severely hit, dropped, or other
  8. Please do not disassemble the jump starter without authorization. Please contact professional maintenance personnel for repairing the jump starter.
  9. When the jump starter is charging, do not use it to start the vehicle;
  10. Be extra cautious during operation to avoid metal tools falling on the jump starter interface (it is easy to cause a short circuit, equipment damage, or an explosion);
  11. When using the jump starter, ensure that the surrounding area is well ventilated;
  12. When starting the vehicle, make sure that the positive and negative contact points on the cable clamp of the jump starter are in good contact with the positive and negative poles of the battery;
  13. Sparks and flames contacting the jump starter and engine is forbidden;
  14. In order to prevent sparks from short-circuiting and damaging the jump starter, it is forbidden to clamp the positive and negative poles of the clamp together or touch the same metal;
  15. Do not place the jump starter where children can reach it;
  16. Do not expose the jump starter to rain or snow;
  17. Do not leave the device in extreme environments for a long time (high temperature: above 131°F (55°C), extreme cold: below 14°F (-10°C), humid: humidity> 80%);
  18. Please store the jump starter in a cool and dry place, and take protective measures if
  19. Please charge the product in time to prevent battery low-voltage or out of power. Long time no power status of the battery may cause the product to fail to charge.

Brief Introduction

  1. Emergency start of 12V engine (up to 8-Liter gasoline and 6-Liter diesel 12 V engines)
  2. Built-in air inflator, support tire pressure detection, preset charging and stopping value, unit switching, and other functions; Air pressure sensor accuracy: ±2 PSI, maximum inflation pressure 150 PSI;
  3. LED lighting (luminous flux: 300 LUMENS, 3modes: SOS/stroboscopic/constant light)
  4. Charging: USB-C(QC3.0, 5V/3A, 9V/2A);
  5. Discharging: USB-A(QC3.0, 5V/3A, 9V/2A);

Parameter Specification

Product Model: JA301 Battery Capacity: 20000mAh(74Wh)
Starting Voltage: 12V Starting Current:  1000A
Peak Current: 2000A Pressure Range: 10~150 psi
Sensor Accuracy: ± 2psi Input: USB-C 5V/3A,9V/2A
Output: USB-A 5V/3A,9V/2A Polarity: Red(+), Black(-)
Operating Temp: -20℃ to 50℃ Charging Temp: 0℃ to 45℃
Storage Temp: -20℃ to 50℃ Service life: >1000 cycles (s  in good condition)
Charging Time: 4~7.5hr Hours

Packing List

Multi-function vehicle
emergency starter| Jump starter clamps| Inflatable hose| Nozzle adapters
---|---|---|---
| | | Lventliaciapter
2.Konische aufMase DOsen
3. Nadeladaoter

Product storage bag| Accessories storage bag| IManual| USB-C cable
| | |

Product Overview

Main interface port:

Main operation interface and screen

  1. Interface display

  2. Description
    **** No.| Functional   Description| No.| Functional   Description
    ---|---|---|---

1

| BAR/PSI unit switch button, and can also be used as a forced start  function switch|

2

| Power button (Short press to turn on, long press for 2 seconds to turn off)

3

| The button for presetting tire pressure: When the tire pressure is presetting, numbers will blink; The blinking will stop after the setting is completed. You may then exit the setting mode. At the same time, the real-time tire pressure will be displayed on the screen|

4

|

Air inflator start-stop button: Hold down the button for 3 seconds to turn on. Press down quickly to turn off

5

| Red light (Abnormal warning indicator for emergency jump start function)|

6

| Greenlight (ON: Forced start mode output; Blinking: Normal start mode output)

7

| Battery indicator light

(Power: 20%、40%、60%、80%、100%; Charging: Marquee)

|

8

|

IN: Charging status indicator

9| USB: USB Status Indicator| 10| ERR: abnormal state alarm
11| BAR / PSI: Tire pressure units setting indicator light| 12| V: Output voltage detection status indication and units
13| Numerical display area| |

Operating Procedure

  1. How to power up the jump starter?
    Press the “Light” or “Power” button;

  2. How to use the jump-start function?

2.1 Method one: Normal start
2.1.1 Connect the jump starter clamps with the EC8 connector to the jump starter;
2.1.2 Connect the red (+) clamp to the positive (+) terminal on the vehicle battery and the black (-) clamp to the negative (-) terminal on the vehicle battery, and make sure that the connections are good;
2.1.3 Press the “Light” or “Power” button to power on the product. The green light on the screen will light up and flash if there are no issues. At this time, you’ll be able to start your vehicle.
2.1.4 If the vehicle starts successfully, the jump starter will automatically disable the power output.
2.1.5 In most cases, the vehicle will be able to start immediately after the jump starter has been connected. Some vehicles may need to be connected to the jump starter for 30~120 seconds (the product will charge the car battery at this time) to continue the operation. If the vehicle does not start immediately, Please wait 20-30 seconds before each attempt. Do not attempt more than five times within 15minutes.
2.1.6 Please remove the jump-start clamps from the car battery instantly after you finished the starting. Press on the “Power” button for 2 seconds to shut down the jump starter. If there are no operations for 60 seconds, the product will automatically shut down;

2.2 Method two: Forced start

(Safety reminder: Under the forced start mode, part of the safety protection mechanism is invalid. Be sure to connect the positive and negative poles correctly, otherwise, it will cause a short-circuit. So please check the instruction manual before operation and use it with caution)
2.2.1 At this time, the normal start mode fails to start, e.g: the voltage of the car battery is very low (the voltage is less than 1V), you can use the forced emergency start function after checking the operating specifications in the manual;
2.2.2 Connect the jump starter clamps to the EC8 connector on the Jump- Starter;
2.2.3 When the jump starter is on, tapping and holding on the “BAR/PSI” button for 5 seconds will enter the forced start mode. At this time, the green light on the screen is always lighting, which means that the output of the ignition clips is normally turned on. At this time, you must prevent the positive and negative poles from being short-circuited; (In this mode, it is required to turn on the forced start function first, and then connect the ignition clips to the car battery, otherwise, the output cannot be turned on);
2.2.4 Connect the red (+) clamp to the positive (+) terminal on the vehicle battery and the black (-) clamp to the negative (-) terminal on the vehicle battery(during the connection process, there will be a slight sparking the phenomenon, which is normal) and make sure that the connections are good; At this time, the overall voltage of the jump starter connected in parallel with the vehicle is displaying on the screen, then you can jump-starting the vehicle;

2.2.5 Shortly press the “Power” or “BAR/PSI” button to exit.

3. How to use voltmeter function

3.1 Connect the jump starter clamps to the EC8 connector on the Jump-Starter;
3.2 Connect the red (+) clamp to the positive (+) terminal on the vehicle battery and the black (-) clamp to the negative (-) terminal on the vehicle battery, and make sure that the connections are good;
3.3 At this time, the green light on the main interface flashes, and the overall positive and negative voltages of the starting power supply connected in parallel with the car are displayed at the same time, and it enters the starting mode. To check only the voltage of the car battery, short press the “ON” button to exit the starting mode and enter the measurement Mode, the “green light” goes out, and the display only displays the voltage value of the car battery, so as to determine whether the battery is damaged;
3.4 Disconnect the alligator clamps from the vehicle battery and exit the voltmeter function mode.

4. How to use the air inflator function?

4.1 The inflatable hose is connected to the output port of the air inflator, and then tighten the nut, and the other end is connected to the car tire;
4.2 To wake the product (short press the “Light” button or short press the “Switch” button) to enter the air inflator mode;
4.3 Short press the “BAR/PSI” button to switch the pressure unit of tire pressure: BAR, PSI;

Pressure conversion table Unit bar kPa PSI kgf/cm2
Value 1 100 14.5 1.02

4.4 To set the target tire pressure value, you must first know the tire pressure requirements of the tire. (For the standard tire pressure value of the tire, you can check the pressure value mark on the tire, or check the manual of the inflated product), set the target tire pressure value by pressing “+ -“. After setting, the value will flash for 3 seconds, exit the setting state and enter the real-time monitoring state of tire pressure; (Safety reminder: If the target tire pressure value of the tire is not set, directly turn on the air pump. At this time, the air pump will not automatically charge and stop. It needs to be turned off manually. If the tire pressure is not monitored in real-time, there will be The risk of excessive tire pressure or puncture)
4.5 Long Press the “PUMP” button for 3 seconds to turn on the air inflator. When the tire pressure reaches the set value, the air inflator will be turned off automatically. To turn off the inflator manually: press the “PUMP” button or the “Switch” button;
4.6 Remove the inflatable hose
(Safety reminder: During the inflation process, the heat generated by the air inflator will cause a local high temperature. Please leave the product for 10 minutes to dissipate heat before removing the inflation tube to prevent scalds)

5. How to use LED light?

  1. Long press the “Light” button for one second, and the LED lights up
  2. Short press the “Light” button in order to switch the modes of ON, Strobe, SOS, and OFF;
  3. Long press the “Light” button for two seconds to turn off the LED light forcefully;

6. How to charge your jump starter

6.1 You will need the following: a USB power adapter(5V output USB power adapter or 9V2A USB power adapter if QC protocol supported) and a USB To Type-C cable.
6.3 In the case of running out of power or low power, please charge the product in time to prevent battery under-voltage. Long-term no power status of the battery may cause the product to fail to charge.
6.2 Plug the USB plug/A Port into the power adapter and the C port into the jump starter‘ s charging port. At this point, the battery indicator and the “In” icon on the screen will turn on, indicating that the product is charging;

7. How to use the 5V USB-A port to charge your mobile phone
7.1 You will need the following: USB To USB-C cable and a mobile phone (if the mobile phone supports 9V2A of QC protocol, it can support 9V2A fast charge)
7.2 When the “USB” icon on the screen light up, plug the USB plug/A Port to the jump starter and the C port into your mobile device;

8. Error code display description

NO. ERROR CODE EXPLANATION REASON/SOLUTION
1 001 When charging or starting, other functions are  not allowed

Disconnect the charger or exit the start mode
2| 110| Charging   overvoltage   protection| Disconnect the charger
3| 111| Charging over-voltage (secondary) protection| Disconnect the charger
4| 120| Charging over-temperature protection| Wait for the product to cool down
5| 130| Charging under temperature protection| Put the product at the right temperature
6| 140| Discharge undervoltage protection| Connect the charger
7| 150| Discharge over-temperature protection| Wait for the product to cool down
8| 160| Discharge under temperature protection| Put the product at the right temperature
9| 200| Communication  abnormal| Restart the device
10| 310| Air inflator short-circuit protection| Restart the device
11| 320| Air inflator over-current protection| Restart the device
12| 330| When starting, the current air pressure is greater than the set air pressure| Reset the proper air pressure
13| 410| When starting, under-voltage protection| Connect the charger
14| 411| Before starting, under-voltage protection| Connect the charger
15| 420| Start over-temperature protection| Wait for the product to cool down

16

|

430

|

The external battery voltage is greater than the device voltage

| 1.  The displayed voltage is lower than 12V, and the device voltage is low. Please connect the charger to recharge.

2.  If the display voltage is higher than 12V, the car battery is normal; or the car battery voltage is too high, which is not suitable for this product, please use a jump starter that supports higher voltage

17| 440| Ignition clip shorted| Connect the battery correctly
18| 450| Ignition clip shorted| Connect the battery correctly
19| 460| Start short circuit protection| Restart the device
20| 470| Abnormal cell voltage drift protection| /
21| 480| Continuous start protection| Wait 30 seconds and start again

Warnings

* Do not disassemble the product as there are no user-serviceable parts. Any maintenance should be operated by professional

  1. Quickly starting your vehicle can be possible when the jump-starter battery’s capacity is more than 50% although your vehicle may not be able to start effectively if the jump starter does not have enough sufficient power.
  2. It is normal for the jump starter to heat up after it is turned on or while the air inflator function is being used.
  3. In order to maintain optimal the life of the battery, charge the jump starter at least once every 3 months;
  4. If the jump starter starts to leak or emit any peculiar smell, stop using it and contact us immediately.
  5. Do not connect the red clamp with the black clamp as this can be dangerous.
  6. Use the original jump starter clamps only.
  7. Stay away from fire and water to avoid safety accidents.
  8. Do not place the jump starter in an environment with temperatures above 60°C and do not allow it to have prolonged exposure to sunlight. Store the jump starter in a cool and dry place.
  9. Do not disassemble or modify this product without approval.
  10. Do not violently knock, press, or shake the jump starter; otherwise, it may cause a fire, explosion, or combustion.
  11. Do not use chemical cleaners to clean this product.
  12. Keep this product away from children.

Recycling Treatment

  1. To avoid irreparable harm to the environment or human beings, do not dispose of the jump starter with other household garbage.
  2. Separate the device from other types of garbage and recycle it in a responsible manner to maintain sustainable use of materials.

Warranty Policy

We offer a limited warranty on the product 12 months from the date of purchase on any defects in materials and workmanship. Conditions are as follows:

  1. The buyer must provide proof of receipt (details on the order page/invoice, etc.) from the official dealer channel to apply for after-sales service
  2. The warranty does not cover damage or malfunction caused by normal wear and tear, physical damage, improper installation, misuse, modification, or unauthorized repairs by third parties.
  3. The manufacturer shall not be liable for any loss or damage caused in transit by a third party or by force majeure.
  4. The manufacturer is not responsible for any incidental or consequential damages arising from the use or misuse of this product.
  5. All warranty claims are limited to the repair or replacement of defective products and are at our sole discretion.
  6. If we repair or replace the product, the product will be covered for the remainder of the original warranty period. We reserve the right to repair or replace refurbished equipment, products, or accessories that may involve the use of the same functions.
  7. Consumable parts, such as batteries, are not covered by the warranty.
  8. The manufacturer reserves the right to change and interpret these terms and conditions of the warranty at its own discretion.

website: www.lokithorshop.com

Documents / Resources

| LOKITHOR JA301 Jump Starter Power Bank Air Compressor [pdf] Instruction Manual
JA301 Jump Starter Power Bank Air Compressor, JA301, Jump Starter Power Bank Air Compressor
---|---
| LOKITHOR JA301 Jump Starter [pdf] User Manual
JA301 Jump Starter, JA301, Jump Starter, Starter

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

LOKITHOR User Manuals

Related Manuals