BANANA HOBBY MiG-25 Foxbat Twin-64mm EDF Jet Instruction Manual
- June 5, 2024
- BANANA HOBBY
Table of Contents
BANANA HOBBY MiG-25 Foxbat Twin-64mm EDF Jet
KIT packing list
- Fuselage x 1
- Left-wing x 1
- Right-wing x 1
- Left vertical fin x 1
- Right vertical fin x 1
- Left horizontal tail x1
- Right horizontal tail x1
- Detachable R40T air-to-air missile x 4
- Detachable Fuel tank x 1
- Nose (including air-speed tube) x 1
- Main wing carbon fiber tube x 1
- Hook and Loop tape x1
- Main wing carbon fiber tube x1
- Hook and Loop tape x1
- Aileron rod x 2
- Rudder rod x 2
- Elevator rod x 2
- Wing flap rod x 2
- Front-wheel steering rod x 1
- Main wing fixing screws x 6 ( silver color)
- Ducts Fan cover fixing screws x 4 (black color)
The accessories are shown below
Kit+Servo version
- Kit
- 9g Servo * 7 (Installed）
- 17g Positive servo *1 (Installed）
- 17g Reverse servo *1 (Installed）
PNP version
- Kit
- 9g Servo* 7 (Installed）
- 17g Positive servo *1 (Installed）
- 17g Reverse servo *1 (Installed）
- 40A ESC 2 & BEC1（Installed）
- 2840-2280kv 6S 2 + 64mm 12-Blade Ducted Fan 2（Installed）
Installation Steps
- Power the 10cm lead 9g servos back to the neutral point and install the arm. Glue the servo into the hole with foam glue or hot glue sticks. The 2pcs horizontal tails all use Positive servo.
- Install the elevator rod on the servo arm and adjust the rod’s length.
- Same to another horizontal tail.
- Power the aileron and wing flap servo back to the neutral point and install the arm. Notice 2 arms in direction.
- Install the aileron rod and wing flap rod, make sure the control surface is flush with wing surface by adjusting the rod’s length
- Same to another wing. Then let the servo lead through the wire way and the plastic parts hole.
- Insert excess lead stuff into preset space of plastic part.
- Open the battery cover, power the landing gear and control all landing gear down.
- Power the front landing gear servo back to the neutral point and install the rod adjuster.
- Glue the front landing gear servo, adjust the rod’s length and fixed the rod.
- Then Glue the front landing gear’s cover.
- Open the ducted fan and ESC‘s cover.
- Install two 17g servos and fix them with glue.
- Let the servo lead through the wire way.
- Use screws install two ducted fans.
- Put ESC into the hole, and connect motor with ESC. Then test the direction of the motor’s rotation .
- Install horizontal tail and fix them with 1.5mm socket head wrench.
- Power servo back to the neutral point and install the arm. Install the elevator rod and adjust the rod length.
- Install ESC cover. Then install ducted fan cover with screws.
- Connect rudder servo, Glue the vertical tail into the fuselage.
- Install wing into the fuselage with carbon fiber tube and fix wing with screws.
- Connect all plugs into the receiver by label.
- Put receiver and lead into the hole behind battery room.
- Install the airspeed tube into the nose.
- The center of gravity of Mig25 is at 125mm behind the wing.
- Adjust the battery’s location by CG, then fix the battery with Hook and Loop tape. You can use a 3300-5200mah 6S battery for Mig25, the best battery type is 4200mah 6S.
- Install four missiles and fuel tank. Then we complete all installation work!
Radio Travel Adjust Suggest Setting
Mig25’s battery position close to CG, so it’s not very sensitive to CG, so
minor error in the servo’s stroke will not seriously affect the flight.
Use D/R mode
- ELEV: POS1 -100% POS2- 80%
- AILE: POS1- 105% POS2- 80%
- RUDD: POS1-100% POS2-75%
- FLAP: First Gear : 70% Second Gear- 100%
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>