sygonix 2612389 5m LED Strip RGB Instruction Manual
- June 3, 2024
- Sygonix
Table of Contents
sygonix 2612389 5m LED Strip RGB
Intended use
- The product is intended for decorative or effect lighting in indoor areas; it may be installed and used only in dry, enclosed indoor rooms.
- The product can be fastened on suitable objects, such as furniture, using the adhesive tape located on the bottom side of the LED strip.
- The lighting programmes and light colours can be selected and controlled via the IR remote control enclosed. The activation of the LEDs on the LED strip takes place via a special control unit, whose power is supplied by the provided wall plug transformer.
- Always observe the safety instructions and all other information included in these operating instructions.
- Any use other than that described above could lead to damage to this product and involves the risk of short circuits, fire, electric shock, etc.
- This product complies with the applicable national and European requirements. All names of companies and products are the trademarks of the respective owners. All rights reserved.
Package contents
- LED strip
- Control unit with integrated IR receiver
- IR remote control (incl. battery)
- Wall plug transformer
- Accessory set (2x screws for mounting the control unit, 3M tape, 4x connection cables, 8x plugs)
- Operating instructions
Up-to-date Operating Instructions
Download the latest operating instructions at www.conrad.com/downloads or scan
the QR code above. Follow the instructions on the website.
Explanation of symbols
A triangle containing a lightning symbol indicates a health hazard, e.g.,
electric shock.
The symbol with the exclamation mark in the triangle is used to highlight
important information in these operating instructions. Always read this
information carefully.
The arrow symbol indicates special information and advice on operation.
Safety instructions
Damages due to failure to follow these operating instructions will void the warranty! We do not assume any liability for any resulting damage! We do not assume any liability for material and personal damage caused by improper use or non-compliance with the safety instructions. In such cases, the warranty will be null and void.
General
- Unauthorised conversion and/or modification of the product is not allowed for safety and approval reasons.
- The product is not a toy and does not belong in the hands of children! Children do not realise the danger arising from the incorrect use of electrical devices. In addition, the product contains small parts and batteries. Therefore, be especially careful when children are around!
- Do not leave packaging material carelessly lying around, since it could become a dangerous plaything for children.
- In commercial institutions, the accident prevention regulations of the Employer’s Liability Insurance Association for Electrical Systems and Operating Facilities are to be observed!
- If you have any questions that are not answered in these operating instructions, please contact our technical department or another specialist.
Installation, connection and operation
-
This product must be installed and used only in dry conditions indoors. The product must not get damp or wet, as the wall plug transformer can pose the risk of a fatal electric shock!
-
Do not use the product in rooms that are under adverse environmental conditions, where combustible gases, vapours or dust are or may be present! There is a risk of explosion!
-
The product must not be exposed to extreme temperatures, strong vibrations or heavy mechanical stress.
-
The product is suitable for use only in moderate climates, not tropical climates.
-
Caution, LED light: Do not look directly into the LED light! Do not look into the beam directly or with optical instruments!
-
The mains socket into which the wall plug transformer is plugged must be easily accessible.
-
Do not pull the wall plug transformer from the mains socket by pulling on the cable.
-
If the wall plug transformer is damaged, do not use the product any longer. Switch off the mains socket to which the wall plug transformer is connected (switch off at the corresponding circuit breaker or remove the safety fuse, then switch off the earth leakage circuit breaker). Unplug the wall plug transformer from the mains socket.
Replace the defective wall plug transformer only with a wall plug transformer of the same design (with the same output voltage, output current, round plug and plug polarity). -
If it can be assumed that safe operation is no longer possible, the device must be turned off and precautions must be taken to ensure that it is not used unintentionally.
Safe operation can no longer be assumed if:- the product shows visible signs of damage
- the product does not work at all or works poorly (where there is flickering light, leaking smoke or a smell of burning, audible crackling noises, or discolouration of the product or to adjacent surfaces)
- the product was stored for a longer period of time in unfavourable conditions
- it was exposed to heavy loads during transport
-
For safety reasons, unplug the wall plug transformer from the mains socket before cleaning the product or when the product is not to be used for a while (e.g., during storage).
Battery instructions
- Batteries should be kept out of the reach of children.
- Do not leave batteries lying around in the open; there is a risk of them being swallowed by children or pets. If they are swallowed, consult a doctor immediately.
- Leaking or damaged batteries can cause burns if they come into contact with the skin. You should therefore wear suitable protective gloves.
- Liquids leaking from batteries are very chemically aggressive. Objects or surfaces coming into contact with these liquids might be considerably damaged. Therefore, store batteries in a suitable location.
- Batteries must not be short-circuited, opened or thrown into a fire. There is a risk of explosion!
- Do not recharge normal, non-rechargeable batteries; there is a risk of explosion!
- Please pay attention to the correct polarity (plus/+ and minus/-) when inserting the battery.
Installation and start-up
Mounting the control unit
Before you start the installation, keep in mind that the IR receiver of the
control unit must be placed so that a flawless reception of the control
signals from the IR remote control is possible.
A direct optical contact between the IR LED of the IR remote control and the
IR receiver is beneficial; however, it is not a prerequisite. The IR light
(invisible to the human eye) of the IR remote control is reflected by many
surfaces.
Before you proceed to the permanent mounting of the control unit and the IR
receiver, check that they function properly.
-
The control unit can be screwed tight via two eyes located on the sides of the housing. Depending on the mounting site, you can also fasten the control unit using cable ties or a double-sided adhesive tape such as the supplied 3M tape.
When you screw the control unit into place, make sure that no cable or pipes are damaged when drilling and tightening the screws. -
Fasten the IR receiver of the control unit to a suitable place, e.g. by using a strip of adhesive tape or a cable tie.
Installing the LED stri p
-
The LED strip can be mounted on suitable surfaces, such as furniture or similar objects, using the adhesive tape located on the bottom side.
The LED strip must be mounted in such a way that it is not exposed to mechanical stress. It may not be mounted in such a way that someone can step on it; that will damage it. -
Carefully clean the surface onto which you want to mount the LED strip from dust, dirt and grease before mounting; otherwise the adhesive tape will come off the surface.
-
Remove part of the protective strip and stick the LED strip onto the mounting surface one section at a time. However, do not use force when pressing down.
- The LED strip can be cut at the marked points. The connection cables provided can be used to restore the electrical connection between the individual LED strip sections.
Connecting the LED strip to the control unit
Connect the 4-pin connection of the LED strip to the corresponding 4-pin
socket of the control unit.
The plug on the control unit should normally be inserted so that the arrow is pointing to the “+” marking on the LED strip. If the LED strip does not turn on, switch off the power supply and rotate the plug by 180°.
The plug connection can be protected from unintentional disconnection by using a strip of adhesive tape.
Connecting the wall plug transformer
- Connect the round low voltage plug of the wall plug transformer to the corresponding round socket on the control unit.
- Connect the wall plug transformer to a proper mains socket of the public supply network.
Inserting the battery into the IR remote control
- Open the battery compartment of the IR remote control and insert a battery of type “CR2025”, paying attention to the correct polarity (pay attention to plus/+ and minus/-). Close the battery compartment again.
- The battery needs replacing if the range of the IR remote control decreases or if the control unit no longer responds to the remote control.
Basic functions of the IR remote control
Point the LED on the front of the IR remote control at the IR receiver of the control unit and press the corresponding button.
“ON” button Switches the LED strip on
“OFF” button Switches the LED strip off
UP button Increases the brightness (not possible in all lighting programmes)
DOWN button Reduces the brightness (not possible in all lighting programmes)
“W” button Light colour “White”
“R” button For selection of the light colour “red”
“G” button For selection of the light colour “green”
“B” button For selection of the light colour “blue”
12 colour buttons For selection of 12 predefined light colours
The four buttons “FLASH”, “STROBE”, “FADE” and “SMOOTH” can be used to start the predefined lighting programmes. Depending on the lighting programme, you can also change the brightness with the button (not possible in all lighting programmes).
Maintenance and cleaning
-
Apart from the occasional battery change for the IR remote control, the product is maintenance-free.
The built-in LED bulbs are permanently installed; they cannot be replaced. -
Before you clean the product, disconnect it from the mains voltage. Pull the wall plug transformer from the mains socket.
-
The outside of the product should only be cleaned with a clean, soft, dry cloth.
Do not use aggressive cleaning agents or chemical solutions for this could damage the housing (discolouring) or impair the operation.
Disposal
Product This symbol must appear on any electrical and electronic
equipment placed on the EU market. This symbol indicates that this device
should not be disposed of as unsorted municipal waste at the end of its
service life.
Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose
of it separately from unsorted municipal waste. Spent batteries and
accumulators, which are not enclosed by the WEEE, as well as lamps that can be
removed from the WEEE in a non-destructive manner, must be removed by end
users from the WEEE in a non-destructive manner before it is handed over to a
collection point.
Distributors of electrical and electronic equipment are legally obliged to provide free take-back of waste. Conrad provides the following return options free of charge (more details on our website):
- in our Conrad offices
- at the Conrad collection points
- at the collection points of public waste management authorities or the collection points set up by manufacturers or distributors within the meaning of the ElektroG
End users are responsible for deleting personal data from the WEEE to be
disposed of.
It should be noted that different obligations about the return or recycling of
WEEE may apply in countries outside of Germany.
(Rechargeable) batteries
Remove batteries/rechargeable batteries, if any, and dispose of them
separately from the product. According to the Battery Directive, end users are
legally obliged to return all spent batteries/rechargeable batteries; they
must not be disposed of in the normal household waste.
****Batteries/rechargeable batteries containing hazardous substances are labelled with this symbol to indicate that disposal in household waste is forbidden. The abbreviations for heavy metals in batteries are: Cd = Cadmium, Hg = Mercury, Pb = Lead (name on (rechargeable) batteries, e.g. below the trash icon on the left).
Used (rechargeable) batteries can be returned to collection points in your municipality, our stores or wherever (rechargeable) batteries are sold. You thus fulfil your statutory obligations and contribute to environmental protection.
Batteries/rechargeable batteries that are disposed of should be protected against short circuit and their exposed terminals should be covered completely with insulating tape before disposal. Even empty batteries/rechargeable batteries can contain residual energy that may cause them to swell, burst, catch fire or explode in the event of a short circuit.
Technical data
General
Total power consumption…………………approx. 24 W
Ambient conditions………………………… Temperature 0 °C to +40 °C, air humidity 10% to
90% relative, not condensing
LED Strip
Length………………………………………….5 m
Cross-section…………………………………(W x H) 10 x 3 mm
Number of LEDs…………………………….150 x RGB
Weight………………………………………….approx. 160 g
Wall Plug Transformer
Operating voltage…………………………..200 – 240 V/AC, 50/60 Hz
Output…………………………………………..12 V/DC, 2.0 A
Control unit
Operating voltage…………………………..12 V/DC
Required current…………………………….min. 2 A
Dimensions……………………………………35 x 50 x 22.5 mm (W x L x H)
Weight………………………………………….23 g
IR remote control
Power supply…………………………………1x battery of type CR2025
Dimensions……………………………………52 x 85 x 7 mm (W x H x D)
Weight………………………………………….17 g (incl. battery)
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240
Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g.
photocopy, microfilming, or the capture in electronic data processing systems
require the prior written approval by the editor. Reprinting, also in part, is
prohibited. This publication represent the technical status at the time of
printing.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>