Philips Audio T5505 Wireless Earbuds-Complete Features/Instruction Manual

Philips Audio T5505 Wireless Earbuds

Specifications

• FEATURES: Rock-solid connectivity. Integrated earbud controls
• BRAND: Philips
• COLOR: Black
• ASSEMBLED PRODUCT DIMENSIONS (L X W X H): 2.90 x 1.40 x 1.30 Inches
• LENGTH: 8 mm

Introduction

These stylish genuine wireless headphones can handle both music and calls. Background noise is blocked by Active Noise Canceling, and the Philips Headphones app allows you to customize the sound. To pause the music, remove an earpiece. Philips Headphones include a sleek design and a hybrid Active Noise Canceling software. Sound customization. Neodymium drivers with an 8 mm diameter. Clear clarity, punchy bass

HEARING SAFETY

• Be sure to observe the following guidelines when using your headset.
• Listen at reasonable volumes for reasonable periods of time.
• Be careful not to adjust the volume continuously upwards as your hearing adapts.
• Do not turn up the volume so high that you can’t hear what’s around you.
• You should use caution or tempo- rarely discontinue use in potentially hazardous situations.
• Excessive sound pressure from earphones and headphones can cause hearing loss.
• Using headphones with both ears covered while driving is not recon- mended and may be illegal in some areas while driving.
• For your safety, avoid distractions from music or phone calls while in traffic or other potentially dangerous environments.

GENERAL INFORMATION

To avoid damage or malfunction

CAUTION

• Do not expose headphones to excessive heat
• Do not drop your headphones.
• Headphones shall not be exposed to dripping, splashing water.
• Do not allow your headphones to be submerged in water.
• Do not use any cleaning agents containing alcohol, ammonia, benzene, or abrasives.
• If cleaning is required use a soft doth, if necessary dampened with a minimum amount of water or diluted mild soap, to clean the product.
• The integrated battery shall not be exposed to excessive heat such as sunshine, fire or the like.
• The danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type.
• Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, can result in an explosion;
• Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid or gas;
• A battery is subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.
• About operating and storage temperatures and humidity
• Store in a place where the temperature is between -20°C (-4°F) and 50°C (122 °F) (up to 90% relative humidity.
• Operate in a place where the temperature is between 0°C (32°F) and 45°C (113 °F) (up to 90% relative humidity.
• Battery life may be shorter in high or low-temperature conditions.
• Replacement of a battery with an incorrect type that can defeat a safeguard (for example, in the case of some lithium battery types);

YOUR TRUE WIRELESS EARPHONES

Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome.

With this Philips True wireless earphone, you can:

• enjoy convenient wireless handsfree calls;
• enjoy and control wireless music;
• switch between calls and music

WHAT’S IN THE BOX

• Philips True wireless earphones Philips TAT5505

• Replaceable rubber ear caps x 3 pairs

• USB-C charging cable (for charging only

• Quick start guide

• Global Warranty

• Safety leaflet

OTHER DEVICES

A mobile phone or device (e.g., notebook, PDA, Bluetooth adapters, MP3 players, etc.) which supports Bluetooth and is compatible to the headset (see ‘Technical data’ on page 8).

OVERVIEW OF YOUR TRUE WIRELESS EARPHONES

• Microphone
• Multi-function touch
• LED indicator (Earpieces)
• LED indicator (charging box)
• USB-C charging slot

GET STARTED

CHARGE THE BATTERY

NOTE

• Before you use your earpieces for the first time, place the earpieces in the charging box and charge the battery for 3 hours for optimum battery capacity and lifetime.
• Use only the original USB-C charging cable to avoid any damage.
• Finish your call before charging the earpieces, as connecting the earpieces for charging will power the earpieces off.

CHARGING BOX$

Connect one end of the USB cable to the charging box, and another end to the power source.

The charging box starts charging.

• The charging process is verified by the blue LED light on the front panel.
• When the charging box is fully charged, the blue light goes on.

TIP

• The charging box serves as a portable backup battery for charging the earpieces. When the charging box is fully charged, it supports 3 times full recharge cycle for the earpieces.

EARPIECES

Place the earpieces in the charging box.

The earpieces start charging.

• The charging process is verified by blue LED light on the earpieces.
• When the earpieces are fully charged, the blue light goes off.

TIP

• Normally, a full charge takes 2 hours (for the earpieces or charging box) by USB cable.

• Pair the earpieces with your Bluetooth device for the first time

• Make sure that the headset is fully charged and powered off.

• Open the top cover from the charging box.

• The LED on both earpieces flashes in white & blue alternately.

• The earpieces are now in pairing mode and are ready to pair with a Bluetooth device (e.g., a mobile phone).

• Turn on the Bluetooth function of your Bluetooth device.

• Pair the earpieces with your Bluetooth device. Refer to the user manual of your Bluetooth device.

NOTE

• After powering on, if the earpieces cannot find any previously connected Bluetooth device, it will automatically switch to pairing mode.
• The following example shows you how to pair the earpieces with your Bluetooth device.
• Turn on the Bluetooth function of your Bluetooth device, and select Philips TAT5505.
• Enter the earpiece’s password “0000” (4 zeros) if prompted. For those Bluetooth devices featuring Bluetooth 3.0 or higher, no need to enter a password.

SINGLE EARPIECE (MONO MODE)

Take either right or Left earpiece out from the charging box for Mono use. The earpiece will power on automatically. There will be a voice “Power on” from the earpiece.

NOTE

• Take the second Earpiece from the charging box and they will pair each other automatically.
• Pair the earpieces with another Bluetooth device
• If you have another Bluetooth device that you want to pair with the earpieces, make sure the Bluetooth function in any other previously paired or connected devices are turned off.
• A long touch over 5 seconds on both left & right side simultaneously with the earpiece on-ear, release when Pairing voice prompt is heard.

NOTE

• The earpieces store 4 devices in the memory. If you try to pair more than 4 devices, the earliest paired device is replaced by the new one.

USE YOUR EARPIECES

CONNECT THE EARPIECES TO YOUR BLUETOOTH DEVICE

• Turn on the Bluetooth function of your Bluetooth device.
• Open the top cover from the charging box.
• The blue LED flashes.
• The earpieces will search the last connected Bluetooth device and reconnect to it automatically. If the last connected device is not available, the earpieces will enter pairing mode

TIP
The earpieces cannot connect to more than 1 device at the same time. If you have two paired Bluetooth devices, only turn on the Bluetooth function of the device that you want to connect.

• If you turn on the Bluetooth function of your Bluetooth device after turning on the earpieces, you have to go to the Bluetooth menu of the device and connect the earpieces to the device manually.

NOTE

• If the earpieces fail to connect to any Bluetooth device within 5 minutes, it will turn off automatically to save the battery life.
• In some Bluetooth devices, the connection may not be automatic. In this case, you have to go to the Bluetooth menu of your device and connect the earpieces to the Bluetooth device manually.

CONTROL ANC (ACTIVE NOISE CANCELATION)

ENABLE ANC

Different ANC modes can be toggled via a double tap on the right earpiece.

• ANC function is auto-active when put into the ear.
• Touch the MFB button twice, it will change to Awareness mode.
• Touch the MFB button twice again, it will turn the ANC function off

ANC LED INDICATOR STATUS

POWER ON/OFF

MANAGE YOUR CALLS AND MUSIC

CALL CONTROL

LED INDICATOR STATUS

CHARGING BOX (4 BLUE LED)

TIP
When USB is off, the LED is lit for the 30s after the case opens or close.

BATTERY LED INDICATOR ON BLUETOOTH DEVICE

It will show a battery indicator on the Bluetooth device after being connected to the earpieces.

VOICE ASSISTANT

HOW TO WEAR

RESET THE EARPIECES

If you encounter any pairing or connection issue, you can follow the following procedure to reset your headset.

• On your Bluetooth device, go to the Bluetooth menu and remove Philips TATS505 from the device list
• Turn off the Bluetooth function of your Bluetooth device
• Tap& hold multi-function touch for 25s on each earpiece individually.
• Return earpieces to charging box & close the lid.
• Follow steps in “Use your earpieces-Connect the earpieces to your Bluetooth device.
• Pair the earpieces with your Bluetooth device, select Philips TATS505

TECHNICAL DATA

• Music time – ANC enabled: 4.5 hours | ANC disabled with Bluetooth: 5 hours
• Talk time – ANC enabled: 4.5 hours | ANC disabled: 5 hours
• Standby time – 200 hours Charging time: 2 hours
• Lithium-ion battery 50 mAh on each earpiece, Lithium-ion battery 410 mAh on charging box
• Bluetooth version: 5.1 Compatible Bluetooth profiles:
• HSP (Hands-Free Profile-HFP)
• A2DP (Advanced Audio Distribution Profile)
• AVRCP (Audio Video Remote Control Profile)
• Supported audio codec: SBC Frequency range: 2.402-2.480 GHz Transmitter power: < 5 dBm Operating range: Up to 10 meters (33 feet)
• Auto power off
• USB-C port for charging
• Low battery warning: available

NOTE
Specifications are subject to change without notice.

NOTICE DECLARATION OF CONFORMITY

Hereby, MMD Hong Kong Holding Limited declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. You can find the Declaration of Conformity on www.p4c.philips.com.

DISPOSAL OF YOUR OLD PRODUCT AND BATTERY

• Your product is designed and manufactured with high-quality materials and components, which can be recycled and reused.
• This symbol on a product means that the product is covered by European Directive 2012/19/EU.
• This symbol means that the product contains a built-in rechargeable battery covered by European Directive 2013/56/EU which cannot be disposed of with normal household waste. We strongly advise you to take your product to an official collection point or a Philips service center to have a professional remove the rechargeable battery.
• Inform yourself about the local separate collection system for electrical and electronic products and rechargeable batteries. Follow local rules and never dispose of the product and rechargeable batteries with normal household waste. Correct disposal of old products and rechargeable batteries helps prevent negative consequences for the environment and human health.

REMOVE THE INTEGRATED BATTERY

If there is no collection/recycling system for electronic products in your country, you can protect the environment by removing and recycling the battery before disposing of the headphones.

• Make sure the earpieces are disconnected from the charging box before removing the battery.

• Make sure the charging box is disconnected from the USB charging cable before removing the battery.

COMPLIANCE WITH EMF
This product complies with all applicable standards and regulations regarding exposure to electromagnetic fields.

ENVIRONMENTAL INFORMATION

All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment.

NOTICE OF COMPLIANCE

The device complies with the FCC rules, Part 15. Operation is subject to the following two conditions:

• This device may not cause harmful interference, and
• This device must accept any interference received, including interference that may cause undesired operation.

FCC RULES

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna. Increase the separation between equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC RADIATION EXPOSURE STATEMENT:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

CAUTION
The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

CANADA
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device

TRADEMARKS

BLUETOOTH
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by MMD Hong Kong Holding Limited is under license. Other trade- marks and trade names are those of their respective owners.

SIRI
Siri is a trademark of Apple Inc., registered in the U.S. and other countries.

GOOGLE
Google and Google Play are trademarks of Google LLC.

FREQUENTLY ASKED QUESTIONS

• My Bluetooth headset does not turn on.
  The battery level is low. Charge the headset.

• I cannot pair my Bluetooth headset with my Bluetooth device.
  The Bluetooth is disabled. Enable the Bluetooth feature on your Bluetooth device and turn on the Bluetooth device before you turn on the headset.

• Pairing does not work?
  Put both earpieces into the charging box.
  Make sure you have disabled the Bluetooth function of any previously connected Bluetooth devices.
  On your Bluetooth device, delete “Philips TAT5505” from the Bluetooth list.
  Pair your headset (see ‘Pair the headset with your Bluetooth device at the first time on page 6).

• The Bluetooth device cannot find the headset.
  The headset may be connected to a previously paired device. Turn off the connected device or move it out of range.
  Pairing may have been reset or the headset has been previously paired with another device. Pair the headset with the Bluetooth device again as described in the user manual. (see ‘Pair the headset with your Bluetooth device at the first time on page 6).

• My Bluetooth headset is connected to a Bluetooth stereo-enabled mobile phone, but music only plays on the mobile phone speaker.
  Refer to the user manual of your mobile phone. Select to listen to music through the headset.

• The audio quality is poor and crackling noise can be heard?
  The Bluetooth device is out of range. Reduce the distance between your headset and Bluetooth device, or remove obstacles between them.
  Charge your headset.

• The audio quality is poor when streaming from the mobile phone is very slow, or audio streaming does not work at all.
  Make sure your mobile phone not only supports (mono) HSP/HFP but also supports A2DP and is BT4.0x (or higher) compatible (see ‘Technical data’ on page 10).

• What is the procedure for connecting my Philips wireless earbuds?
  Make sure the headset’s earpieces are turned off. Press and hold the multi- function button on both earpieces for 3 seconds. The white LED in both earpieces flashes three times before changing to blue. Both earpieces are now turned on and connected to one another.

• What can I do to make my Philips wireless headphones work?
  Android users must go to Bluetooth Settings to pair Bluetooth headphones or speakers. By tapping the three-dot icon on the right, you can now enter the Advanced Settings section. Turn it on if it isn’t already enabled. Users will be able to connect to two devices at the same time this way.

• What is the best way to charge Philips earbuds?
  To avoid any damage, only use the original USB charging cord. • Connecting the earpieces for charging will turn the earpieces off, so finish your call before charging them. One end of the USB cable should be plugged into the charging case, while the other should be plugged into the power source. The charging case begins to charge.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>