BODYCRAFT SP-Bracket-001-ASM SP-Bracket for Indoor Training Cycles Owner’s Manual

June 5, 2024
BODYCRAFT

BODYCRAFT logo

BODYCRAFT SP-Bracket-001-ASM SP-Bracket for Indoor Training Cycles

BODYCRAFT SP-Bracket-001-ASM SP-Bracket for Indoor Training
Cycles

Assembled Parts List – SP Bracket

BODYCRAFT SP-Bracket-001-ASM SP-Bracket for Indoor Training Cycles
1

Part # Assembly Parts List QTY

SP-Bracket-001-ASM

| ****

Main Frame Assembly

| ****

1

SP-Bracket-010a| Hexagon Sleeve – Large| 1
SP-Bracket-010b| Hexagon Sleeve – Small| 1
SP-Bracket-014| Cable Clip Mount| 5

NOTE:

  • SPX or SPX-Mag use part #10a (larger Hexagon Sleeve)
  • SPR or SPT-Mag use part #10b (smaller Hexagon Sleeve)

Product Assembly

STEP 1: Remove Cap

  • Remove the existing Cap Screw (M5 x P1.0 x 10mm L ) (A) below the handlebar tube, on the right or left side, using a 4mm Allen Wrench. Set aside for reinstallation during STEP 3.
  • Then continue by pulling out the existing Plastic Hex Cap (B) from the handlebar tube.

BODYCRAFT SP-Bracket-001-ASM SP-Bracket for Indoor Training Cycles
2

NOTE: This Plastic Hex Cap (B) will no longer be needed, but you might want to keep for future use if the SP-Bracket is taken off.

STEP 2: Install Hexagon Sleeve

  • Insert the correct Hexagon Sleeve into the handlebar tube, aligning the hole to match the side of the Cap Screw during STEP 3a.
    •  SPX or SPX-Mag use part #10a (larger Hexagon Sleeve)
    •  SPR or SPT-Mag use part #10b (smaller Hexagon Sleeve)
    • NOTE: Double confirm the Cap Screw HOLE in the Hexagon Sleeve lines up with the bottom hole on the handlebar tube.
  • Then continue by installing the Main Frame Assembly (01-ASM) into the Hexagon Sleeve (10a or 10b).
  •  Confirm the Main Frame Assembly (01-ASM) inside the tube, is not extended out past the “Max” line marked on top of frame.

BODYCRAFT SP-Bracket-001-ASM SP-Bracket for Indoor Training Cycles
4

STEP 3: Securing Frame
Secure both the Hexagon Sleeve (10a or 10b) and the Main Frame Assembly (01-ASM) to the handlebar tube using the existing Cap Screw (M5 x P1.0 x 10mm L ) (A) from STEP 1.

BODYCRAFT SP-Bracket-001-ASM SP-Bracket for Indoor Training Cycles
6

STEP 4: Install Connect-22
Secure the Connect-22 to the Vesa-100 Bracket (7) using the hardware pre- attached to the back of the Connect-22.

  •  4: Flat Washers (M5)
  •  4: Lock Washers (M5)
  • 4: Philips Head Screws (M5 x 1.0p x 15mm L)

BODYCRAFT SP-Bracket-001-ASM SP-Bracket for Indoor Training Cycles
7

STEP 5: How to install Cable Clip Mounts

  •  Clean surface with mild spray soap or a window cleaner and dry with a 100% cotton rag.
  • Take adhesive strip off back of Cable Clip Mount.
  •  Place Cable Clip Mount and hold for 15 seconds.
  • Install Cable under clip while gently holding the back. NOTE: DO NOT over stretch clip mount opening. Only open enough to gently slide the cable under the mount.

BODYCRAFT SP-Bracket-001-ASM SP-Bracket for Indoor Training Cycles
8

STEP 6: Install Cable Clip Mounts

  •  Find below which Indoor Training Cycle you have. Install a Cable Clip Mount at each arrow location.
  • Then fully install the cable with the 2.5mm power cord end at the Connect-22 back plug. Follow the Cable Clip Mounts with the cable to the base of the Cycle.

BODYCRAFT SP-Bracket-001-ASM SP-Bracket for Indoor Training Cycles
9

Parts from the Connect 22

BODYCRAFT SP-Bracket-001-ASM SP-Bracket for Indoor Training Cycles
10

Detailed Parts List & Parts Exploded View

BODYCRAFT SP-Bracket-001-ASM SP-Bracket for Indoor Training Cycles
11

Part # Detailed Parts List QTY
SP-Bracket-001 Main Frame 1
SP-Bracket-002 Universal Joint 1
SP-Bracket-003 Flat Washer, CP 8 x D18 x 1.5t 1
SP-Bracket-004 Nut, UCP M8 1
SP-Bracket-005 Top Cap 1
SP-Bracket-006 Axle – Black 1
SP-Bracket-007 Vesa 100 Bracket 1
SP-Bracket-008 Washer, SS φ8 x φ22 x 2t 2
SP-Bracket-009 Nut SS M8 2
SP-Bracket-010a Hexagon Sleeve – Large 1
SP-Bracket-010b Hexagon Sleeve – Small 1
SP-Bracket-011 Set Screw, M6 x P1.0 x 6mm L 1
SP-Bracket-012 Plastic Washer, D18mm x 8.2mm x 0.5t 1
SP-Bracket-013 Gasket, D14mm x 8.2mm x 1.5t 1
SP-Bracket-014 Cable Clip Mount 5

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals