Hunter TX51 Ceiling Fan Remote Control Instruction Manual
- June 5, 2024
- Hunter
Table of Contents
****
Hunter TX51 Ceiling Fan Remote Control
HUNTER FAN COMPANY CONTROL LIMITED WARRANTY
The Hunter Fan Company makes the following limited warranty to the original
purchaser
of the Control (“Control”): Your Control is warranted to be free from defects
in material and workmanship for a period of one year from the date of sale. If
the Control malfunctions or fails within the warranty period due to a defect
in material or workmanship we will replace it free of charge. IF THE ORIGINAL
PURCHASER CEASES TO OWN THE CONTROL, THIS WARRANTY AND ANY IMPLIED WARRANTY,
INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE, ARE VOIDED. THIS WARRANTY IS IN LIEU OF ALL
OTHER EXPRESS WARRANTIES. THE DURATION OF ANY IMPLIED WARRANTY, INCLUDING, BUT
NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, IN RESPECT TO ANY CONTROL, IS EXPRESSLY LIMITED TO THE
PERIOD OF THE EXPRESS WARRANTY SET FORTH ABOVE FOR SUCH CONTROL. This warranty
excludes malfunctions or failures which were caused by repairs by persons not
authorized by us, mishandling, improper installation, modifications, or damage
to the Control while in your possession, or unreasonable use. This warranty
does not apply to batteries or to deterioration or damage to the product
caused by the use of faulty batteries. To obtain a replacement, return your
Control postage prepaid along with proof of purchase to Hunter Fan Company
Service Department at 7130 Goodlett Farms Pkwy., Memphis, TN 38016. IN NO
EVENT SHALL HUNTER FAN COMPANY BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL
DAMAGES. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS OR THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES
SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY
GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY
FROM STATE TO STATE.
Read and Save These Instructions
This product conforms to UL Standard 1917.
WARNINGS This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna, Increase the separation between the equipment and receiver, Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Note: Any changes or modifications to the transmitter or receiver not expressly approved by Hunter Fan Company may void one’s authority to operate this remote control. Chemical burn hazard. Keep batteries away from children. This remote contains a lithium button cell battery. If a new or used lithium button/coin cell battery is swallowed or enters the body, it can cause severe internal burns and can lead to death in as little as 2 hours. Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. Dispose of cells properly and keep away from children. Even used cells may cause injury.
If you are installing multiple remote-controlled fans on the same circuit
breaker, you may need to perform a few extra steps to prevent interference or
faulty operation of your remote controls.
Go to www.HunterFan.com/FAQs and click “How
do I properly install multiple remote-controlled fans?” for more information.
Installation
Turning off the power
Before installation, use the pull chains to set the fan speed to HIGH and the light to ON. Ensure the power is OFF at the outlet box and wall switch location before proceeding with installation.
WARNING
To avoid possible electrical shock, before installing your fan, disconnect the
power by turning off the circuit breakers to the outlet box associated with
the wall switch location.
Removing the canopy
Remove the canopy. If uncertain how to remove it, reference the fan’s owner’s
manual. With wiring exposed, it may be helpful to note existing wire
connections or take a digital photo for reference. Remove the wire connectors
that connect the wires from the outlet box to the fan, leaving the grounding
wires connected.
Installing the receiver
Choose the hanging system that most closely resembles the one used by your
fan, and install the receiver and wire as directed.
You may have installation issues if the fan is installed on an angled ceiling.
For assistance, call 1-888-830-1326.
Note: Some fans may have considerable excess lead wire. For easier canopy
installation, cut the excess wire, leaving a minimum of 8” remaining. Re-strip
the fan lead wires 1/2”. Place remaining excess wire into the ceiling
electrical box. The bracket and fan must remain properly grounded.
Examples of receiver connections
Wiring
Note: If you are uncertain about wire colors or connections, please contact a qualified electrician.
Connecting the ground wires
Using an orange wire connector, connect the 3 grounding wires (green, green/yellow stripe, or bare copper) coming from the ceiling, downrod, and hanging bracket.
Wiring the receiver to the fan (continued)
Using the orange wire connectors, connect the blue wire from the receiver to
the blue wire (or possibly black with white stripe wire) from the fan. Connect
the yellow wire from the receiver to the black wire from the fan.
Wiring the receiver and fan to the ceiling
Using the orange wire connectors, connect the black wire (ungrounded) from the
ceiling to the black wire from the receiver. Connect the white wire (grounded)
from the ceiling to both the white wire from the receiver and the white wire
from the fan.
AFTER ALL WIRES ARE CONNECTED and secured with wire connectors, re-install the
canopy.Turn the splices upward and push them carefully back through the hanger
bracket into the outlet box. Spread the wires apart, with the grounded wires
on one side of the outlet box and the ungrounded wires on the other side of
the outlet box.
Installing the battery
To access the battery compartment, remove the small Phillips head screw that
secures the battery door to the remote control.
Replace the used battery with a CR2032 battery when necessary. The battery
should be installed with the positive (+) side up.
Turning on the power
IMPORTANT
Reference the included remote function card for information on how to use your control!
The remote transmitter is already paired to the receiver and ready to use.
Note: If your need to pair your remote, remove the battery door. Cycle
power to the fan by turning power off and back on at the wall switch (or
circuit breaker if necessary). Within three minutes, press the pair button on
the remote.
To prevent faulty operation, please disconnect power from all other ceiling
fans within range while pairing.
Trouble Shooting
Remote Control of Fan is Erratic
- Make sure the battery is installed correctly.
- Install a fresh battery.
Multiple Remote Issues
If you have multiple remotes or multiple remote-controlled fans installed on the same circuit breaker and you are experiencing interference or faulty operation of your remote controls, please go to www.HunterFan.com/FAQs and click “How do I properly install multiple remote-controlled fans?” for information on how to correct this issue.
Cradle Installation
Remove the cradle from the cradle bracket.
You have two options to install the included remote control cradle to the wall. Choose which path works best for you.
Option 1
Using screws
Choose your cradle installation location.
If you are installing into drywall, drill two 9/64 width holes using the
cradle bracket as a guide. Gently hammer the included drywall anchors into the
pre-drilled holes.
Install the cradle bracket to the wall with the included screws.
Option 2
Using Adhesive Strip
-
Apply the adhesive sticker to the back of cradle bracket per the instructions on the adhesive sticker.
-
Press the cradle bracket against the wall and hold firmly for 30 seconds.
-
Snap extertal magnetic cradle onto cradle bracket by aligning inside corners of magnetic cradle with outside corners of cradle bracket and firmly press into place.
-
Remote can magnetically attach to cradle.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>