amber connect AMB365G Wireless GPS Tracker Smart Vehicle Security User Manual

: June 5, 2024
: amber connect

Table of Contents

amber connect AMB365G Wireless GPS Tracker Smart Vehicle Security
Accessories
Specification
LED Indications
Getting Started
Troubleshooting
Read User Manual Online (PDF format)
Download This Manual (PDF format)

amber connect AMB365G Wireless GPS Tracker Smart Vehicle Security

Accessories

Device
Charging cable
Relay
User manual

Specification

Dimension	78.041.013.0mm
Weight	38g
Voltage Range	7.5-90V
Backup Battery	270mAh/3.7V
Operation Temperature	-20°C to +70 °C
Humidity	20% to 80%
Standby Time	50 hours
GSM Frequencies	850/900/1800/1900 MHz
GPRS	Class 12, TCP/IP
GPS Channel	66
GPS Sensitivity	-165dBm
Acquisition Sensitivity	-148dBm
Position Accuracy	<10m
TTFF (Open sky)	Cold start <45s, Hot start <2s
GSM/GPS Antenna	Built-in design
LED Indicator	GSM-green, GPS-blue, Power-red
Data Transmit	TCP, SMS
Geo-fence	Alarm activated when the vehicle enters or leaves the specified

area
Speeding Alarm| Alarm activated when speed goes higher than the pre-set value
Low Power Alarm| Alarm activated when backup battery is running out.
Non-movement Detection| Movement alarm activated by built-in 3D motion sensor
Mileage Report| Track by time/distance interval
Remote engine mobilization/immobitization| Mobilize/immobilize engine

LED Indications

GPS LED Indicator – RED|
---|---
Flashing| Low battery
Slow flashing| Fully charged/ functioning normally
Solid red| Charging
Off| Power off or low battery
GPS LED Indicator – BLUE|
Flashing (interval 0.1s)| Searching for BD/GPS signal
Solid blue| BD/GPS positioned
---|---
Off| GPS asleep or off
GPS LED Indicator – GREEN

Quick Flashing| GSM initializing
Slow flashing| Receiving GSM signal normally
Solid green| Connected to GPRS network
Off| No GSM signal or no SIM card

Getting Started

Please follow the instructions below to ensure safe and correct use of your device. Note: Please ensure that there is enough credit on your SIM card. If you will be using the GPRS function, pay attention to the current SIM card GPRS charge.

Switch on
Begin by assembling and setting up your device before its first use.
- Open the SIM card cover.
- Insert the SIM card.
- Turn the battery switch to ON.
- Close the SIM card cover and connect the device to the external power line, which will be used to charge the terminal and built-in battery.
Switch off
- Toggle the battery switch to OFF.
Charge the device
Plug in the device to connect or plug in the charging cable. The charging cable with 2A FUSE for short-circuit over current protection.
Installing the device
Find a location inside the vehicle where the device will not be found. Your device has a built-in GSM antenna and a GPS antenna. During installation, please ensure that the device is facing up:
Under the dashboard below the front windshield.
In the parcel shelf the rear.
In the front bumper (non-material face), ensure the device does not get wet.
Under the wiper version (non-metal), ensure the device does not get wet.
Noncovert installation: affix the device to the dashboard below the windshield.
Device wiring
The standard voltage is 9V-90V; the red wire is the positive and the black wire is the negative
Connect the black wire ground.
Device wiring diagram
Subject to permissible laws in your country. Play close attention to the diagram description; the battery is 9-90V and the relay remains12V/ 24\/.
Power/ACC/Tele-cut-off (petrol/electricity) control line (4 pin)
Your device comes with a power cord and is designed to use only manufacturer-specified wiring accessories. The re line is positive while the black is negative (this side should not be connected to the ground wire).
The ACC line (orange) connects to the ACC switch of the vehicle. Please be sure to connect to the ACC line, otherwise the device will not detect ignition status.
Engine immobilization (petrol/electricity) control line (yellow) is connected to pin 86 Tele-cutoff (petrol/electricity) relay (equal to the yellow line of the relay socket)