tint Kea 404067 Smart Pendant Lamp Instruction Manual

tint Kea 404067 Smart Pendant Lamp Instruction

General information

Included with the item

• tint ceiling light, white+color
• tint remote control with wall bracket and installation material
• Installation material
• 2 batteries LR03 (AAA) / 1.5 V
• Operating manual

Dear customers!
This user manual contains important information on start-up and use. Before using the tint product, please read through the user manual carefully. This particularly applies for the safety notes. Failure to follow this user manual may result in severe injury or damage the bulbs. Store the user manual for future use. If you pass the tint product on to third parties, please be absolutely sure to include this user manual. You can also download the manual: www.hey-tint.de

Explanation of symbols
The following symbols and signal words are used in this user manual, on the product or on the packaging.

WARNING!
This signal symbol/word designates a hazard with moderate degree of risk which may lead to death or severe injury if not avoided.

ATTENTION!
This signal symbol/word designates a hazard with low degree of risk which may severe a moderate injury if not avoided.

NOTICE!
This signal word warns against potential damages to property
This symbol gives useful additional information for handling or operation. Please read carefully.

Safety Instructions

• Do not expose this lamp to moisture
• Not dimmable by conventional dimmers
• Protective insulation according to protection class II
• The light source and control gear of the surrounding product cannot be replaced by the user. Only authorised agencies may replace them!

Proper use
This ceiling light is used for lighting purposes and, after connecting to the corresponding remote control, can be controlled and/or integrated in a Smart Home System with the Zigbee radio standard.
Up to 50 tint products can be controlled with the remote control.
The ceiling light must only be mounted on walls/ceilings with the permissible load capacity. The item is unsuitable for commercial use.

Safety Notes

• This product may be used by children ages eight and over as well as persons with impaired physical, sensory or mental capacities or tho-se lacking experience and knowledge if they are supervised or have been instructed in how to safely use the light and have understood the risks associated with using it.

WARNING!

DANGER for children

• Children are not allowed to play with the item
• Do not let children play with the packaging. Children may get caught in it when playing and suffocate.
• Keep the batteries and the tint remote control out of reach for children. If a battery has been swallowed or is in any part of the body, medical help must be sought immediately
• Batteries can be life-threatening if swallowed.
• If the battery compartment does not close safely, make sure you stop using the product and keep it away from children.

DANGER of electric shock

• Before use, make sure that the existing power voltage matches the required operating voltage of the item (see „Technical data“)
• Before installing, de-energise the mains wiring: Switch off the circuit breaker, or remove the fuse and secure to prevent reactivation.
• When inserting the batteries, pay attention to the right polarity.
• Do not use different types and do not use a used battery and a new battery with each other.
• Do not use the item if it is damaged.
• Avoid contact of the item with water or other liquids.
• The product can be adjusted via the included tint control or other con-trol units on a Zigbee basis. A conventional dimmer must not be used.

DANGER of fire/combustion and/or explosion

• Risk of explosion if the battery is improperly replaced. Replace the batteries only with the same or equivalent type of battery. Note the
  „Technical data.“

• Batteries must not be charged, reactivated, taken apart, thrown into the fire or short-circuited. Otherwise, there is an increased risk of explosion and phase-out, and gases can also escape!

• Avoid contact of battery fluid with skin, eyes and mucous membranes.

• In case of eye contact, rinse the affected areas immediately with plenty of clear water and see a doctor immediately.

• When inserting the batteries, pay attention to the right polarity

• Always replace all batteries at the same time.

• Do not use different types and do not use a used battery and a new battery with each other.

ATTENTION!

CAUTION against damage to property

• Remove the batteries from the remote control when they are drained or if you are not using the item for a long time. In this way, you avoid damage that can result from leakage.
• Do not expose the batteries to extreme conditions, e.g. by storing them on radiators or in direct sunlight. Increased risk of leakage!
• If necessary, clean the battery and device contacts before inserting them.

tint remote control

Setup

Inserting the batteries

1. Open the battery compartment at the rear of the tint remote control.
2. Insert 2 LR03 (AAA) / 1.5V batteries as shown on the bottom of the battery compartment. Ensure the correct polarity of the batteries (+/-).
3. Close the battery compartment cover again.

Using the wall bracket (optional)
You can use the wall bracket (supplied) to store the tint remote control safely. A magnet in the bracket will hold the tint remote control safely in the bracket.

Mounting the wall bracket

1. Remove the protective film from both sticky pads.
2. Press the bracket with some force against a clean, dry and dust-free surface.

Screwing in the wall bracket
Depending on the surface, the wall bracket can be attached to the wall with screws and wall plugs if required. Screws and wall plugs are inclu-ded with the bracket.

ATTENTION!
Make sure there are no pipes or wires in the wall where you intend to drill.

1. Separate the two halves of the bracket. (fig. 1)
2. Use the rear of the bracket as a stencil to mark where you will drill.
3. Drill the holes and insert the wall plugs (if needed) in the holes. (fig. 2)
4. Screw the rear of the bracket onto the wall.
5. Place the upper part of the bracket on the screwed lower part. (fig. 3)

The bracket can now be used.

Installing the ceiling light

1. Before installing, de-energise the mains wiring: Switch off the circuit brea-ker, or remove the fuse and secure to prevent reactivation.

2. Use the wall bracket to mark the holes to be drilled in the ceiling.
   Make sure not to drill any cables or pipes in the area.
   Drill at the marked points and insert the dowels. Now fasten the bracket with the corresponding screws.

3. Connect the connection cable to the terminal strip. Make sure that the cables are secure.

4. Install the ceiling light as shown in the illustration.

5. Reactivate the breaker.

Operation

The tint ceiling light is already connected to the supplied remote control and can be controlled directly. Further tint lamps and lights must first be integrated in the remote control (see chapter „Operation – Adding a new tint product“).
The tint remote control is a radio remote control.

• You do not need to “aim” at the tint products with the tint remote control to operate them.
• The tint remote control will also penetrate solid materials such as walls, doors and windows.
• The maximum range (depending on the obstacles between the tint remote control and the tint products) is approx. 30 metres in the open air.
• Each button press will be confirmed by the feedback display lighting up.

Basic functions Switching on/off

Press the standby button to switch the other tint product on and off again. The memory function will store the last “illumination state” and will start again automatically the next time the tint product is switched on.

Set colors

Press one of the four colour keys (fig. 4) to select the

• desired color:
• Short press: The color will switch in the desired direction on the color scale.
• Long press: The color will jump to a permanently stored color value.

Set white tone
Short-press to select permanently stored white tone settings: warm white, neutral white and cold white.
Long-press to set the desired white tone from a continuous scale that reaches the super-warm white range.

Set brightness
Short-press to select permanently stored brightness levels: 100%, 80%, 50%, 20%, 10% and 5%.
Long-press to set the desired brightness on a continuous scale.

Scenes
‘Scenes’ are pre-defined light settings.
Activate a scene by short-pressing the corresponding button on the remote control.

• Working light” scene: 100% neutral, bright light
• “Sunset” scene: Starts at warm-white light (50%) and then dims further after 15 minutes. After another 10 minutes, the light switches off.
• “Party” scene: Starts a bright and constantly changing sequence of colors.
• “Night light” scene: Warm-white light dimmed to 5%.
• “Campfire” scene: Simulates a campfire in warm color tones, changing between orange, red and white.
• “Romantic” scene: A constant cycle between the colors red, pink and purple.

If you are using a „tint white“ product that only emits white light, the colored light features will not be available. The tint product may be switched off.

Group functions
This is a group
The ceiling light is in the first group to begin with. It is possible to control several bulbs or other tint products with only one button. This is useful if you have more than one ‘lighting situation’ in a room, for example.
Example:

• A workplace that needs to be brightly lit.
• A seating area that needs medium brightness.
• Another area that needs different lighting.

Please note:

• You define yourself what a group actually is. You could group together the tint products in a room or on a floor, for example.
• A group can be expanded or made smaller and tint products can be moved from one group to another.
• An individual tint product could also be a group all on its own.
• You can use the tint remote control to control a maximum of 4 groups, whereby the fourth group is a combination of the other three groups.
• Think beforehand about which tint products you want to group together and try to make the groups logical and comprehensible. This means you will be able to use the groups later using the group button quickly and without having to waste time testing them.

Using the group button

• The first time the group button is pressed, the LEDs above it will show which group you are in.
• Pressing it again will advance you one group.
• You are in the next group when the following LED above the group button lights up:
  • LED 1 for the first group
  • LED 2 for the second group
  • LED 3 for the third group
  • LED 1, 2 and 3 for all groups

Adding a new tint product

• Take note of the technical specifications when purchasing new tint pro-ducts. We recommend tint tint bulbs and luminaires from Müller-Licht. When using products made by other manufacturers, it is not guaranteed that all features will be supported or will work as intended.

Integrate each product in the remote control one at a time and turn off the others during the connection.

1. Plug the new tint product in at the mains and set the corresponding light switch to I or ON.
   The new tint product will signal that it is in coupling mode by briefly increasing and decreasing its brightness and changing color if appli-cable. If this does not occur, switch the product off and on again 5 times

2. Press the group button repeatedly until all the LEDs above the group button light up.

3. Hold the tint remote control very close (< 5 cm) to the new tint product (or to its radio controller).

4. Hold down the group button until the tint product begins to blink.
   The feedback display will first blink red evenly; then, it will begin to blink more quickly.
   This means that the tint remote control has found a signal.
   Continue to hold down the group button until the new light flashes 3 times to indicate that it has been connected to the tint remote control.Keep holding down the group button until the tint product blinks again one time, which shows that it has been assigned to default group (=group 1).

5. If desired, you can select a different group by repeatedly pressing the group button (middle LED = group 2 etc.).
   After approx. 10 seconds, the new tint product will be added to the selected group and the feedback display will stop blinking. Wait this long, not pressing any buttons during this time.
   The procedure will then end and you can use the extended group as normal.

Remove a tint product from the tint remote control

1. Switch the tint product off (to standby) with the tint remote control if necessary.

2. Select the group you would like to change using the group button.

3. Hold down the group button for approx. 5 seconds.
   The feedback display will blink red/green.

4. Select the desired tint product by pressing the group button repeatedly. The tint product will signal that it has been selected by increasing and decreasing its brightness. The tint product will blink in the order in which they are stored in the tint remote control.

5. Hold down the standby button for approx. 5 seconds. The tint product will then signal that it has been removed from the tint remote control by flashing and then dimming.

Shift a tint product from one group into another group

1. Switch the tint product off (to standby) with the tint remote control if necessary.

2. Select the group you would like to change using the group button. (If you would like to add a tint product from group 2 to group 1, for example, press the group button repeatedly until the middle LED above the group button lights up).

3. Hold down the group button for approx. 5 seconds. The feedback display will blink red/green.

4. Select the desired tint product by pressing the group button repeatedly. The tint product will signal that it has been selected by increasing and decreasing its brightness. The tint products will blink in the order in which they are stored in the tint remote control.

5. Hold down the group button again until the selected tint product starts to blink again.
   The group display for group 1 will also light up.

6. Using the group button, select (if necessary) the group to which you would like to add the tint product while the feedback display still is blinking red/green. The selected bulb will be assigned to default group (=group 1) if group button is not pressed at all. After approx. 10 seconds, the tint product will be added to the selected group and the feedback display will stop blinking. Wait this long, not pressing any buttons during this time.
   The procedure will then end and you can use the extended group as normal.

Reset

Reset to 100% light
The tint light bulbs and luminaires can be easily reset by light switch to the basic setting of warm white and 100% brightness. This may be necessary, for example, if you have dimmed the tint products before and the remote control‘s batteries are empty. This feature may also be used in the normal case if you do not have the tint remote control on hand.

1. Use the light switch to switch the tint product off and on again 3 times (interval: 1 second on, 3 seconds off).
2. The tint product will now start in its basic setting, warm white, 100%.

Resetting the tint product
Resetting the tint ceiling light is only required in exceptional cases, such as when the remote control has had to be reset or when you want to integrate the ceiling light into a smart home gateway.

1. Switch the tint product on and off 5 times (interval: 1 second on, 3 se-conds off).
2. Switch the tint product on again. Depending on the tint product, a short cycle through the colors appears or the tint product flashes briefly. The reset has occurred as desired. Wait for 10 seconds, afterwards, you can connect the tint product to a tint remote control and/or a Zigbee gateway as described above.

Resetting the tint remote control
A reset will only be required in exceptional cases, such as when the tint product no longer responds to the tint remote control after removing and reinserting the batteries.
Resetting the remote control will delete all pre-defined group settings and you will have to connect the tint remote control and the tint pro-ducts again afterwards.

1. Remove the battery compartment cover.
2. Use a pointed object or the battery compartment cover to press the reset button on the back of the remote control.
3. Then, proceed as described in the section “Resetting the tint product” and then as described in the section “Adding a new tint product”. Each tint product will then have to be connected individually one after the other. If, for example, three bulbs belong to one group, you must repeat the steps in “Adding a new tint product” 3 times.

Smart Home Ready
The tint products from MÜLLER-LICHT can be controlled using the latest Zig-bee radio standard 3.0 and are compatible with a range of light
control systems, such as Philips Hue* (without Hue Entertainment and without HomeKit integration), Samsung SmartThings, Amazon’s voice assistant (using Amazon Echo Plus or other Echo devices with integrated Zigbee Smart Home Hub)** and many more. More information about the Zigbee Alliance can be found at www.zigbee.org.
For integration in a Smart Home gateway/app, the tint product must be reset, see „Resetting the tint product“. This initially clears the connection to the tint remote control.

• Restrictions on individual services possible, updated information on www.mueller-licht.de/tint/kompatibilitaet
• If this service is available in your country.

Integration in a Zigbee gateway:

• Start the search in the corresponding app.
• Only now switch on the tint product (in pairing mode), even if this is specified differently in the app.
• The tint product is found by the app within a few seconds and flashes briefly for confirmation. Depending on the app, the search takes a few seconds after which the tint product is displayed in the app as a new device and can be named as required.
  A separate connection procedure must be carried out for each tint product. To avoid problems, turn off all other tint products while pairing a new tint product to the app.

The tint remote control can also be integrated in some Zigbee gateways, so that app and remote control can be used in parallel. Instructions and further information can be found at www.hey-tint.de

Cleaning

Turn off the light and turn off the room protection at the fuse box.
Clean the tint product and remote control only with a dry cloth. If not in use, keep them in a dry place protected from children.

Troubleshooting

dead and must be replaced. The tint product itself is switched off or the mains plug is not plugged in. You have selected the wrong group, or have not selected a group, using the group button. Select the right group or select “All groups” by pres- sing the group button repeatedly (all LEDs above the group button will

light up).

The wrong tint product lights up.| Use the group button to select the right group or use the group button

to select “All groups”.

The light switches off suddenly.| You have selected the “Sunset”

scene. Not an error.

You have added a new tint product and this bulb switches off when you

select a colored light function.

| The new tint product can only light up in white. Not an error.
You want to add a new tint product, but the ones that are already added are blinking.| Switch off the tint product that are already added or remove them from the product that has already been

connected.

The tint product has been added to the wrong group.| Find out for sure which group the tint product is in. Proceed as descri- bed in “Add a tint product from one

group into another group”.

I cannot add a tint product to a new

system.

| Please check whether the tint pro-

duct is in coupling mode.

remote control or a gateway. Please remove it from the existing network

Bring it closer to the remote control Switch off any nearby Zigbee devices

I have to press the standby button several times.| If the tint product has previously been switched off using the light switch, the tint remote control will have to resynchronise.

You have switched off parts of the system using a light switch. The tint

remote control is resynchronising.

Which group is my tint product in at the moment?| Simply switching the groups on and off again will tell you which group your tint product is in.

Answers to other frequently asked questions, see www.hey-tint.de

Technical data

• Frequency band of wireless RF mode: 2405-2480.0 MHz
• Maximum transmission power: <20 mW
• Radio range (free field): 30 m
• Remote control: 3V (2x AAA/LR03)

Environmental conditions:

• Temperature (operation): – 20 ° C … 40 ° C
• Temperature (storage): -25 ° C … 60 ° C
• Relative humidity: 5-95% (no condensation)

This product contains a light source of energy efficiency class F.

Declaration of Conformity
Hereby Müller-Licht International GmbH declares that the radio equipment type „Müller-Licht tint“ complies with the directive 2014/53 / EU.
The full text of the EU Declaration of Conformity is available at the following
Internet address : www.hey-tint.de

Dispose

Old appliances must not be disposed of with normal household waste. In accordance with Directive 2012/19/EU, the device must be disposed of properly at the end of its service life. The recyclable materials contained in the device are recycled and pollution of the environment is avoided.Return the old device free of charge to a collection point for electrical waste or a recycling yard.

Before disposal, remove the battery from the device and dispose of it separately.
Batteries and rechargeable batteries should not be disposed of with household waste. Every consumer is legally obliged to hand over batte- ries and rechargeable batteries to a collection point in his/her munici  pality, district or to a retailer.
All batteries and rechargeable batteries can thus be disposed of in an environmentally friendly manner. Batteries and rechargeable batteries containing harmful substances are marked with this symbol and chemical symbols (Pb for lead).
Dispose of the packaging materials in an environmentally friendly manner by placing them in the collection containers provided.
General recycling symbol Further information can be found under: www.mueller- licht.de/recycle/

Installing the ceiling light

References

• tint â–· Smartes Lichtsystem für Dein Zuhause
• tint â–· Smartes Lichtsystem für Dein Zuhause
• Start - MÜLLER-LICHT
• CSA-IOT - Connectivity Standards Alliance

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>