LLURIA D-IN9 RGB LED Strip Owner’s Manual
- July 29, 2024
- LLURIA
Table of Contents
LLURIA D-IN9 RGB LED Strip
Specifications:
- Model: D-IN9 RGB
- Reference: D-IN9-RGB-1P
- Color: Red, Green, Blue
- Lumens/m: 75 (Red), 185 (Green), 40 (Blue)
- Power: 9W/m, 45W total
- Voltage: 12V
- LED Type: 5050
- LED Quantity: 60 per meter
- IP Rating: IP20
- Control System: WS2815 SPI
Product Usage Instructions
Installation:
- Ensure the power source is off before installation.
- Connect the LED strip to the power supply following the correct polarity (+ to +, – to -).
- Mount the LED strip in the desired location using the adhesive backing.
- For lengths exceeding 10m, additional power supply units may be required.
Control System Setup:
Use the DB-CT-8 control system to manage the RGB colors and effects of the LED strip. Follow the control system manual for detailed programming instructions.
Maintenance :
Regularly clean the LED strip with a dry cloth to prevent dust buildup that may affect brightness and performance.
FAQ :
-
Q: Can I cut the LED strip to a custom length?
A: Yes, you can cut the LED strip at designated cut marks to achieve a custom length. Be sure to seal the cut ends properly to avoid damage. -
Q: What is the maximum length of LED strip I can connect in series?
A: The maximum series connection length depends on the power supply capacity and voltage drop. Consult the user manual for specific guidelines on series connections.
High-quality flexible digital LED strip light
Ideal for all types of installations, general lighting, accent lighting and
decorative lighting.
For indoor use.
FEATURES
Reference
Control system
DB-CT-8
Technical data
- Potencia Power 9W/m
- Roll power 5m 45W
- IP 20
- Voltage 12V
- LED type 5050
- LEDs/m 60
- LEDs/px 1
- Px/m 60
- Chip IC WS2815
- Signal SPI
- Pixel continuity Sí Yes
- Pitch 16,7mm
- Beam angle 120º
- cutting lenght 16,7mm
- Roll length 5m
- Life time 50.000h
- Ambient temperature -25~60ºC
- Storage temperature -40~80ºC
- Warranty years 3
- Needs heatsink Sí Yes
- Needs controller Sí Yes
Dimensions
Circuit diagram
Respect the schematic that will be delivered with the position of each of elements and the resupply.
Assembly detail
- Do not bend the LED strip to adapt them to sharp radius or angle.
- Check that the direction of the arrows or the text “LLURIA” are in the right direction.
- Check the operation of the LED strip before placing it on the profi le.
- The installation of the system must be done without the power being switched on.
- Avoid using the same ignition and wiring or to put LED strips near a 220V signal or devices that may cause interference (motors, fans, washing machines, etc.).
- Follow the order of the installation according to the schematic.
- Leave zones with registers to access amplifi ers, sources and resupply.
- Avoid passing wires in front of the LEDs in the installation to avoid shadows.
- The section of the power wiring from the source to the diff erent resupplies must have a minimum section of 1.5mm for lengths of 10m, 2.5mm for lengths of 20m and 4mm for lengths of 30m.
Life time
The life time of our LEDs is 50.000h at an ambient temperature of 23ºC and
provided with a heat dissipation system.
Off cycles are recommended to extend the life of the LEDs.
Warnings
- To ensure the life of the LED, it is request to place on a surface that dissipates the heat they generate.
- Caution when handling cables to avoid damage to the welds.
- The voltage surges can cause damage.
- If diffuser is used with the dissipating profile, there may be variations in the color temperature.
Lluria reserves the right to modify specifications.