JFA K600 Remote Control Instruction Manual

: October 30, 2023
: JFA

Table of Contents

DESCRIPTION
OPERATION
BASIC COMMANDS TRANSMITTER UNIT
BASIC COMMANDS OF THE RECEIVER UNIT
ENCODING THE CONTROL
Documents / Resources

JFA K600 Remote Control Instruction Manual

DESCRIPTION

The K600 allows you to control by distance¹ the main functions of the “player” and change music, folder, volume, pause, play and power.

OPERATION

Transmitter unit: Whenever an o key is pressed, an RF (radio frequency) signal, will be transmitted to the receiving unit. Receptor unit: The “led action” will light up indicating the presence of the received signal, and will transmit in IR (infra red) the code corresponding to the key pressed. The receiver can operate with two transmitters, to do this, per form steps 1 and 2 of the item “CODING THE CONTROL” for the new transmitter.

IMPORTANTE
The control panel will not work if the coding procedure is not carried out. To avoid interference, install the receiver in a location where the antennais close to the panel and at least 50 cm away from the car alarm receiver.

¹For a longer range, install the equipment in a location where the antenna is free and the most exposed as possible, the distance achieved is 600 meters in open area.

BASIC COMMANDS TRANSMITTER UNIT

Overview

Volume control (+);
Volume control ( _ );
Rewind the music;
Advance the music;
LED indicator;
Go up the folder;
Go down the folder;
Play / pause / ATT;
Power / function (switches to aux, CD, USB, radio, etc.).

BASIC COMMANDS OF THE RECEIVER UNIT

Overview

RF receiver antenna;
Led action, reception indicator;
12v power supply (black white stripe) and GND (black).
Infra-red emitter (point to the front of the player);
Memory mode key

ENCODING THE CONTROL

LEARN MODE:
The receiver has more than 220 models of audio and video devices stored in its memory see the attached table or on the website: jfaeletronicos.com

Control:

Press the “M” key on the receiving unit (Indication 1), the action LED will be constantly lit;
Press the keys on the transmitting unit (Indication 2) corresponding to the “player” model, as shown in the table, example: If you want to program the SONY cd, perform step 1 and then press the keys in sequence on the control. Check that the led will ash 1 time and then 4 times, indicating that model 14 (Sony) has been programmed.
After completing this process, press the “M” key on the receiving unit (Indication 1) or wait 10 seconds to exit the memory mode.

RECOMMENDED RECEIVER INSTALLATION

The installation of the equipment in the sound system is done through a polarized power cable. Make sure the white-striped wire from the receiver unit is connected to the battery’s direct positive (+12V) and the black wire to the negative (GND).
Intruction

The receiving unit should preferably be xed away from metal parts and the car’s bodywork (which degrades the transmission) keeping, whenever possible, the antenna unobstructed to allow the greatest possible range of the equipment. Position the infrared emitter, from the receiver unit aimed at the player’s panel, so that there are no obstacles between them. It is recommended to install the receiver unit in the trunk and the IR emitter in the center of the rear window, pointing towards the front of the player. Make sure the wires are not crushed in the installation process.
Intruction

RECOMMENDATIONS AND NOTES

Install the receptor unit at least 1 meter of the Alarms central or electronic injection module. It is recommended to install receptor in the trunk and the infrared emitting in the rear seat pointing to the front of the “CD player”.
For greater range should keep the antenna stretched and in a location that is visual and away from the car bodywork.
supply the receiving unit with 12V.
The receptor can operate with two transmitters; for this, performing steps 1 and 2 to the new transmitter. This feature is recommended for customers using the Slim control on the steering wheel and a K1200 to control by distance from the player.

TECHNICAL SPECIFICATIONS

UNITY RECEIVER	Operating voltage: 9 to 16 V

Stand-by consumption: 13 mA
Reverse polarity protection: YES
UNITY TRANSMITTER| Battery model: A 23 – 12 V
Operating Frequency: 433.92 MHz
Reverse polarity protection: NO
Radiated power (3 meters): 0.808 mW
Modulation: ASK

“This equipment operates on a secondary basis,have not the right of protection against armful interference, even of the same type of station, and notmay cause interference to systems operating in primary basis. “