PHILIPS ADD5910M Water Dispenser User Manual

Water Dispenser
ADD5910M

User Manual

Important

Necessary precautions must be taken when using electrical appliances, and these include the following:

• Read all instructions carefully before using.
• Install the appliance according to the Installation instructions in this user manual.
• Never use the appliance if the power cord or plug are damaged or if the appliance itself is faulty.
• Ensure that the power cord does not come into contact with hot surfaces.
• Never place the appliance body, plug or power cord in water or other liquids. Always wipe clean with a damp cloth.
• Do not operate the appliance when the water is below the minimal water level to avoid damaging the heating elements.
• Do not store or use this appliance outdoors.
• Do not let the cord hang over the edge of table or counter, and do not place the appliance on hot surface.
• Do not place the appliance on or near any gas or electric burner or inside heated oven.
• Do not put the appliance into a working disinfection cabinet.
• Do not freeze the appliance in the refrigerator.
• Do not lean the appliance or operate it upside down.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliances by a person responsible for their safety.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical. sensory or mental capacities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
• Children shall not play with the appliance add space and user maintenance shall not be made by children without supervision.
• Make sure to operate the appliance when children are under good custody.
• This appliance is not a toy, please make sure the children do not play with it.
• Please ensure the appliance is used on a firm and flat surface out of reach of children. to avoid being overturned in a sudden and result in the scald or hitting injury.
• To protect against a fire, electric shock or another personal injury, do not immerse any part of the appliance in water or other liquid.
• Do not touch the hot surface, water spout when the appliance is operating.
• While the appliance is under working, do not touch or block the steam outlet by hand or other stuff, do not open the water tank lid in a rush, in order to avoid the scald by the hot steam or cause any other malfunctions.
• To avoid being scalded, it is prohibited to use hand or any parts of your body to feel the temperature or steam when the appliance is using.
• Do not use the appliance to heat anything other than water. Do not fill above the ‘Max” indication. Do not operate it if water is below minimum.
• Unplug the appliance before cleaning and make sure it is cooled down thoroughly.
• If the power cord is damaged, it must be replaced by the manufacturer or its service agent or a similar qualified person in order to avoid any hazard.
• The power cord could only be replaced by the exclusive power cord if any damages.
• Do not operate the appliance when it is out of order or with malfunctions, return it to the nearest authorized service agent or manufacturer for examination, repair or replacement, do not try to disassembly it by yourself.
• This appliance is intended to be used in household and similar locations such as: — staff kitchen areas in shops, offices and other working environments: — farm houses; — hotels, motels and other residential type environments; — bed and breakfast type environments.
• Warning: misuse may cause injury.
• The heating element surface is subject to residual heat after use.
• Please save this instruction booklet.
• This product is intended to filter municipal water only. Do not put water of unknown quality or that has been microbiologically impaired into the product. Use only cold or room temperature water. Do not use for the preparation of baby food.
• Consume filtered water within 24 hours.
• Appliance outlet and other items may be hot after using.
• Be cautious of the hot steam when dispensing water 3401.
• Do not move the appliance unless the power cord is unplugged.
• Failure to follow these instructions could cause scalding or damage to the product.
• WARNING: Do not put power strips or power banks at the rear of the appliance.
• If only a small amount of water is dispensed, there may be a temperature deviation. We suggest preheating the vessel.
• There may be a big water volume or temperature deviation if limescale builds up inside the heating element. Please descale according to chapter 5.

Parts and features

This is an intant heating water dispenser. With instant heating technology, it provides hot water with different temperatures within seconds. Thanks to the Philips Micro X-Clean filter, you can always enjoy the crisp and pure tasting water at home.

1. Control panel
2. Nozzle
3. Drip tray plate
4. Drip tray
5. Water tank cover
6. Filter
7. Inner water tank
8. Water tank

Control panel

| Tea program
OD Press to quickly set 1001, 250m1.
---|---
Safety lock
When hot water a40t is chosen, press to unlock before pressing the dispense button. Press to wake up the appliance during sleep mode.
Water temperature selection
Press to choose desired water temperature.
Water volume selection,
. Press to choose desired water volume.
Dispense button
Press to start or stop dispensing.
Cleaning/descale button
Long press for 3 seconds to start the cleaning/descaling process. During cleaning/descaling. 11/419 press the button to pause, and press it again to restart. Note: the whole descale process is around 10minutes and cannot be stopped till it is finished.
Descale indicator
Lights up when it is time to descale. Lights off after the descaling process completes.
Water shortage Indicator
Lights up when the water in the water tank is below the minimum level. Please refill the water tank.
Filter lifetime indicator
4 grids light up: the filter has a full lifetime. 2 grids light up: the filter has half of the lifetime left. 4 grids flashes: the filter reaches the end of life.
Filter lifetime reset
Long press both buttons for 3 seconds to reset the filter lifetime.

Main technical specifications

AWP210 (1-pack) AWP211 (3-pack) AWP212 (6-pack)
Rated voltage| 220-240V-
Rated frequency| 50/60Hz
Rated power consumption| 2200W-2600W
Applicable water source| Municipal tap water
Anti-shock level| I
Type of protection| IPXO
Applicable inlet water temperature| 5C-38°C

Installation

Before using the appliance for the first time

• Remove all packaging.
• Remove the tank lid and extract the inner water tank and water tank. Wash, rinse and dry thoroughly.
• Clean the appliance as per the first time cleaning instruction in chapter 5.

WARNING: PLEASE DO NOT DISASSEMBLE THIS APPLIANCE YOURSELF. ELECTRIC ELEMENTS WILL BE EXPOSED AND THERE IS A RISK OF ELECTRIC SHOCK.
Positioning of appliance

• Do not install this appliance in a very damp or hot place, or near heat source.
• Place appliance on a flat and even surface.
• Do not use this appliance outdoors. This appliance is only suitable for use indoors.
• WARNING: DO NOT INSTALL THIS APPLIANCE IN DIRECT SUNLIGHT.
• Ensure that the ventilation on both sides is never blocked or covered.

 How to use

Clean the appliance first as per the first time cleaning instruction in chapter S. Fill water tank through to the ‘MAX” mark: water will flow through the filter at a set rate and may take some time due to the action of the filter cartridge.

1. Plug in.
2. Place mug or glass on drip tray.
3. Select the desired temperature and volume (A-1).
4. Press the safety lock button to unlock the appliance (not applicable for ambient water) (A-2).
5. Press the dispense button to start dispensing (A-3).
   

Note

• The appliance will automatically go to sleep mode if no operation within 1 minute. Touch the safety lock button to wake up the appliance.
• Please discard the water in the drip tray when it’s full of water.
• There could be a temperature deviation of ±5C. There could be a volume deviation of ±10%. The actual temperature and volume depends on using environment and local tap water quality.

Clean and Maintenance

First time cleaning
1. Preparing the filter cartridge

• Remove the packaging. It is common that its surface may have some carbon powder, this is normal. These particles are harmless and are washed off during the preparation process.
• Soak the filter cartridge in clean water for 15 minutes. Shake the filter cartridge slightly to wash off the carbon powder

2. Preparing the appliance

• Remove the inner water tank.
• Ensure the seal ring is installed correctly.
• Press the filter cartridge into the the inner water tank. Ensure it is firmly secure (B-1).
• Reinsert the inner water tank into the water tank.
• Fill the water tank with 2L of cold tap water and refit the water tank into the appliance.
• Place drip tray and drip tray plate in front of the appliance (B-2).
• Place a lug or vessel under the dispense outlet.
• Plug in.
• Dispense ambient water till the water tank is empty.
• Discard the water dispensed. Your appliance is now ready to use.

Routine maintenance

• If the appliance is not used for more than 72 hours. we recommend cleaning it before using. – Discard the water in the water tank. Flush the tank. – Refill It with 1L of fresh tap water. – Dispense ambient water till the water tank is empty. – The appliance is ready to use.
• Wash. rinse and dry the inner water tank. water tank and the tank cover regularly. at least when the filter cartridge is replaced.
• Wash drip tray with soapy water. Rinse all soap away with clean water. Allow to air dry.

Note

• Water is a foodstuff. We recommend using the filtered water within 24 hours.
• Should the appliance being unused for an extended period of time (for example a holiday) we recommend removing the filter and place it in a sealed plastic bag and store in the fridge. This will help to maintain the hygiene of the fitter. Before using the filter after storage, follow the preparation and installation instructions for use as normal.
• Always switch off and unplug the appliance before cleaning.
• Ensure the appliance is cool before cleaning.
• Do not use scouring pads, solvents or abrasives to clean as they may damage the appliance.

Descaling

•  The descale Indicator lights up when the appliance requires the descale process.
• For safe and efficient operation of your appliance, it is important to descale regularly.
• Untreated scale deposits prevent the element conducting heat efficiently and may affect its performance.
• Ensure the inner water tank and filter are removed before starting descale process.

Descale Procedure

1. Remove the filter and the inner water tank.

2. Fill the water tank to the maximal water level, with 1:20 citric acid solution (16 of citric acid per 20ml water).

3. Place a 2L container under the dispense nozzle.

4. Long press the descale button for 3 seconds. (C-1)

5. The descale indicator will flash and the appliance will run a descale process. It will need around 5 mins. Caution: dispensed solution will be hot.

6. When the water shortage indicator lights up, discard the remaining citric acid solution, refill with fresh tap water to the maximal water level.

7. The appliance will run a cleaning cycle.

8. The descale indicator will turn off once the descaling completes.

9. Pull out the nozzle downwards. Rinse it with clean tap water. (C-2)

10. Install the nozzle back. Ensure it is assembled in place. (C-3)

11. Re-insert the filter and inner water tank. The appliance is ready to use.

Note

•  During descaling, press descale button to pause, press it again to restart.

• DO NOT cut off the power during descaling.

• The descale process cannot be stopped till it is finished.
  Replacing the filter cartridge To ensure the best performance, please change the filter cartridge according to the filter lifetime indicator, or the suggested replacement cycle.

• Please clean and install the filter cartridge as per the first-time cleaning instructions above.

• Reset the filter lifetime by long press and for 3 seconds.

first.

Filter lifetime indicator
4 grids light up: the filter has a full lifetime.
2 grids light up: the filter has half of the lifetime left.
No grid lights up: the filter reaches the end of life.

Troubleshooting

the safety lock button to wake up the appliance.
The appliance is not connected with power.| Plug in the power plug. If it does not work, please contact
consumer care.
The appliance does not dispense hot water.| The appliance is not connected with power.| Plug in the power plug.
The water in the water tank is below the minimal water level.| Fill the water tank up to the maximal water level.
The dispense button is locked.| Press the safety lock button to unlock.
Button/display panel does not respond.| The appliance is not connected with power.| Plug in the power plug.
The appliance is in sleep mode.| Touch safety lock button to wake up the appliance.
There is condensed water on the display after dispensing hot water.| Wipe the panel with adrycloth. If It does notwork, please contact consumer care.
Leakage of the water tank| The water tank is not sitting well on the base.| Lift up the water tank and refit it Into the appliance. Ensure it is firmly inserted.
The sealing valve at the bottom of the tank Is faulty.| Please contact consumer care.
The appliance does not dispense ambient water.| The appliance is not connected with power.| Plug in the power plug.
The water in the water tank is below the minimal water level.| Fill the water tank up to the maximal water level.
The water pump is damaged.| Please contact consumer care.
Unstable water flow.| Umescale builds up in the heating element.| Follow the descaling instruction in chapter 5 to descale.
Slow water flow.| Limescale builds up in the heating element.| Follow the descaling instruction in chapter 5 to descale.
There is air in the water pump.| Fill the water tank up to the maximal water level.
Water shortage indicator lights up.| The water in the water tank is below the minimal water level.| Fill the water tank up to the maximal water level.
Odd taste of the water.| The appliance is not cleaned thoroughly after descaling.| Follow step 6-9 in chapter 5 descale instruction to clean the appliance.
The filtered water is not used for a long time.| Discard the remaining water in the water tank and refill with fresh tap water.
The filter has reached the end of life.| Please replace with a new filter cartridge.
Error Code| What does it mean| Solutions
---|---|---
El| The Inlet water temperature sensor Is abnormal.| Please contact consumer care.
E2| The outlet water temperature sensor Is abnormal.| Please contact consumer care.
ES| Dry heating alarm| Cut off the power. Contact consumer care.
EU| Display panel malfunction.| Please contact consumer care.

Guarantee and service

If you need information or if you have any questions, please visit the Philips website at www.philips.com or contact the consumer care center in your country. If there is no consumer care center in your country, go to the local dealer.

 Packing list

This symbol on the products and accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper disposal or treatment, recovery and recycling, please take these products to designated collection points where they will be accepted on a free of charge basis. In some countries you may be able to return your products to your local retailer upon the purchase of a new product. Disposing of this product correctly will help you save valuable resources and prevent any possible effects on human health and the environment, which could otherwise arise from inappropriate waste handling. Please contact your local authority for further details of your nearest collection point for WEEE. Penalties may be applicable for the incorrect disposal of this product in accordance with national legislation.
Please keep this user manual for future reference

Register your product and learn more in the website link below:www.philips.com/water
Specifications are subject to change without notice
**2021 AquaShield All rights reserved. The Philips trademark and the Philips Shield Emblem have registered trademarks of Koninklijke Philips N.V. used under license. This product has been manufactured by and is sold under the responsibility of Hong Kong AquaShield Health Technology Company Limited and Hong Kong AquaShield Health Technology Company Limited is the warrantor in relation to this product Rev A JUN 21**

Documents / Resources

| PHILIPS ADD5910M Water Dispenser [pdf] User Manual
ADD5910M, Water Dispenser, ADD5910M Water Dispenser
---|---
| PHILIPS ADD5910M Water Dispenser [pdf] User Guide
ADD5910M Water Dispenser, ADD5910M, Water Dispenser, Dispenser
| PHILIPS ADD5910M Water Dispenser [pdf] User Manual
ADD5910M Water Dispenser, ADD5910M, Water Dispenser, Dispenser

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>