MINN KOTA 1358763 CoPilot for Freshwater Trolling Motor Owner’s Manual

June 5, 2024
MINN KOTA

MINN KOTA - logo

MINN KOTA 1358763 CoPilot for Freshwater Trolling
Motor

COPILOT ACCESSORY
FOR POWER DRIVE
Owner’s Manual
Compatible with PowerDrive motors manufactured in 2017 or after.

INTRODUCTION

THANK YOU
Thank you for choosing Minn Kota. We believe that you should spend more time fishing and less time positioning your boat. That’s why we build the smartest, toughest, most intuitive trolling motors on the water. Every aspect of a Minn Kota trolling motor is thought out and rethought until it’s good enough to bear our name. Countless hours of research and testing provide you the Minn Kota advantage that can truly take you “Anywhere. Anytime.” We don’t believe in shortcuts. We are Minn Kota. And we are never done helping you catch more fish.

REGISTRATION
Remember to keep your receipt and immediately register your product. A registration card is included with your product or you can complete registration on our website at minnkotamotors.com.


SERIAL NUMBER
Your Minn Kota 11-character serial number is very important. It helps to determine the specific model and year of manufacture.
When contacting Consumer Service or registering your product, you will need to know your product’s serial number.
We recommend that you write the serial number down so that you have it available for future reference.

NOTICE: The serial number on your CoPilot is located on a label inside your product package. We recommend placing the label on the inside of the Sideplate or storing your serial number label in a secure location.

Model:—————————————-
Serial Number:——————————
Purchase Date:—————————–
Store Where Purchased:—————–

NOTICE: Do not return your Minn Kota motor to your retailer. Your retailer is not authorized to repair or replace this unit. You may obtain service by calling Minn Kota at 800-227-6433; returning your motor to the Minn Kota Factory Service Center; or sending or taking your motor to any Minn Kota authorized service center. A list of authorized service centers is available on our website, at minnkotamotors.com. Please include proof of purchase, serial number, and purchase date for warranty service with any of the above options.
Please thoroughly read this user manual. Follow all instructions and heed all safety and cautionary notices. Use of this product is only permitted for persons that have read and understood these user instructions. Minors may use this accessory only under adult supervision.

COMPATIBLE WITH POWERDRIVE MOTORS MANUFACTURED IN 2017 OR AFTER.

This remote is not compatible with PowerDrive V2 or Legacy PowerDrive motors. Check to see that the model name on your serial number tag includes “BT” to ensure compatibility. Model names that do not end in “BT” are not compatible with this remote. Motors manufactured in 2017 have a serial number that begins with the letter R. Serial Numbers starting with a letter before R in the alphabet were manufactured prior to 2017, and are therefore not compatible.

WARRANTY

WARRANTY ON MINN KOTA COPILOT ACCESSORIES
Johnson Outdoors Marine Electronics, Inc. (“JOME”) extends the following limited warranty to the original retail purchaser only. Warranty coverage is not transferable.

Minn Kota Limited One-Year Warranty on the Entire Product
JOME warrants to the original retail purchaser only that the purchaser’s new Minn Kota CoPilot Accessory will be materially free from defects in materials and workmanship appearing within one (1) year after the date of purchase. JOME will (at its option) either repair or replace, free of charge, any parts found by JOME to be defective during the term of this warranty. Such repair or replacement shall be the sole and exclusive liability of JOME and the sole and exclusive remedy of the purchaser for breach of this warranty.

Exclusions & Limitations
This limited warranty does not apply to products that have been used commercially or for rental purposes. This limited warranty does not cover normal wear and tear blemishes that do not affect the operation of the product or damage caused by accidents, abuse, alteration, modification, shipping damages, negligence of the user or misuse, improper or insufficient care, or maintenance. DAMAGE CAUSED BY THE USE OF OTHER REPLACEMENT PARTS NOT MEETING THE DESIGN SPECIFICATIONS OF THE ORIGINAL PARTS WILL NOT BE COVERED BY THIS LIMITED WARRANTY. The cost of normal maintenance or replacement parts that are not in breach of the limited warranty is the responsibility of the purchaser. Prior to using products, the purchaser shall determine the suitability of the products for the intended use and assumes all related risk and liability. Any assistance JOME provides to or procures for the purchaser outside the terms, limitations, or exclusions of this limited warranty will not constitute a waiver of the terms, limitations, or exclusions, nor will such assistance extend or revive the warranty. JOME will not reimburse the purchaser for any expenses incurred by the purchaser in repairing, correcting, or replacing any defective products or parts, except those incurred with JOME’s prior written permission. JOME’S  AGGREGATE LIABILITY WITH  RESPECT TO COVERED PRODUCTS IS LIMITED TO AN AMOUNT EQUAL TO THE PURCHASER’S ORIGINAL PURCHASE  PRICE PAID FOR SUCH PRODUCT.

Minn Kota Service Information
To obtain warranty service in the U.S., the product believed to be defective, and proof of original purchase (including the date of purchase), must be presented to a Minn Kota Authorized Service Center or to Minn Kota’s factory service center in Mankato, MN. Any charges incurred for service calls, transportation or shipping/freight to/from the Minn Kota Authorized Service Center or factory, labor to haul out, remove, re-install, or re-rig products removed for warranty service, or any other similar items are the sole and exclusive responsibility of the purchaser. Products purchased outside of the U.S. must be returned prepaid with proof of purchase (including the date of purchase and serial number) to any Authorized Minn Kota Service Center in the country of purchase. Warranty service can be arranged by contacting a Minn Kota Authorized Service Center or by contacting the factory at 1-800-227-6433 or email service@minnkotamotors.com. Products repaired or replaced will be warranted for the remainder of the original warranty period [or for 90 days from the date of repair or replacement, whichever is longer]. For any product that is returned for warranty service that JOME fi nds to be not covered by or not in breach of this limited warranty, there will be billing for services rendered at the prevailing posted labor rate and for a minimum of at least one hour.

NOTICE: Do not return your Minn Kota product to your retailer. Your retailer is not authorized to repair or replace products.
NOTICE: THERE ARE NO EXPRESS WARRANTIES OTHER THAN THESE LIMITED WARRANTIES. IN NO EVENT SHALL ANY IMPLIED WARRANTIES
INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, EXTEND BEYOND THE DURATION OF THE RELEVANT EXPRESS LIMITED WARRANTY. IN NO EVENT SHALL JOME BE LIABLE FOR PUNITIVE, INDIRECT, INCIDENTAL, CONSEQUENTIAL, OR SPECIAL DAMAGES. Without limiting the foregoing, JOME assumes no responsibility for loss of use of the product, loss of time, inconvenience, or other damage.

Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations and/or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state.

FEATURES

NOTICE: Specifications are subject to change without notice. This diagram is for reference only and may differ from your actual motor.

INSTALLATION

INSTALLING THE COPILOT
Your new CoPilot accessory comes with everything you’ll need to directly install it on your trolling motor. These instructions are intended to show how to install your CoPilot into the PowerDrive. Please review the parts list, mounting considerations, and tools needed for installation prior to getting started. For additional product support, please visit minnkotamotors.com.

INSTALLATION PARTS LIST

Item /
Assembly

| Part #| Description|

Qty.

---|---|---|---
A| 2994112| CTRL BOARD V2 COPILOT RECEIVER|
B| 2994020| TRANSMIT, ASY, PD/AP COPLT (SUB)| 1
1| 2373418| SCREW-#8 X 5/8 PPHSMS S/S| 2
2| 2374092| CTRL BOARD V2 COPILOT RECEIVER| 1
3| 2390801| LANYARD. REMOTE| 1
A| 2377166| MANUAL – CO-PILOT POWERDRIVE| 1

✖ This part is included in an assembly and cannot be ordered individually.
****Not shown on Parts Diagram.

MINN KOTA 1358763 CoPilot for Freshwater Trolling Motor -
COPILOT

MOUNTING CONSIDERATIONS

WARNING

We recommend installing your CoPilot while the boat is on your trailer in a stable position. The motor should be secured and disconnected from a power source before beginning installation.

TOOLS AND RESOURCES REQUIRED

  • 2 Phillips Screw Driver

  • 3 Phillips Screw Driver

INSTALLATION
Installing the CoPilot Receiver

  1. a. Make sure that the Power Cables from the battery are disconnected, or that the breaker, if equipped, is “off.”
    WARNING
    Make sure the motor is mounted on a level surface and is not connected to a power source.MINN KOTA 1358763 CoPilot for Freshwater Trolling Motor - Power
Cables

  2. b. Using a #2 Phillips Screwdriver, remove the four 1/4-20 x 5/8’’ Screws from the Right Sideplate and Left Sideplate of the PowerDrive mount.MINN KOTA 1358763 CoPilot for Freshwater Trolling Motor - Sideplate Screw

  3. c. Remove the Right Sideplate.MINN KOTA 1358763 CoPilot for Freshwater Trolling Motor - Sideplate d. Swing the Left Sideplate out and away from the Base Extrusion.MINN KOTA 1358763 CoPilot for Freshwater Trolling Motor - Swing

  4. ITEM(S) NEEDED
    MINN KOTA 1358763 CoPilot for Freshwater Trolling Motor - Swing
2 e.
    Turn the Right Sideplate over and position the CoPilot Receiver (Item #2) on the inside of the Right Sideplate so that the receiver mounting holes are aligned with the Sideplate Mounting Holes. Position the wires so that they pass to the right of the CoPilot Receiver. This should consist of a Foot Pedal Connection, a Power Connection, and an Antenna wire.
    f. Using the two #8 x 5/8’’ screws (Item #1) provided, insert the screws through the receiver and into the Right Sideplate. Be sure that the wires are not
    pinched in the Sideplate Mounting Holes when tightening the two screws. Do not overtighten.
    MINN KOTA 1358763 CoPilot for Freshwater Trolling Motor -
INSTALLATION

  5. g. With the Right Sideplate laying flat, and the CoPilot receiver that was just installed facing upwards, route the yellow wire antenna around the pegs protruding from the Right Sideplate along the right and bottom edge of the CoPilot Receiver. Follow the grooves in each of the pegs.
    h. Deploy the motor.
    i. On the mount, lift the Center Housing to access the components below. The Center Housing can be released by depressing the tabs on each side that keep it latched to the Base Extrusion.

  6. j. Once lifted, using a #3 Screwdriver, remove the single screw holding the Strain Relief Bracket in place.
    k. Release the Power Cable and Motor Cable Plug from the Strain Relief Bracket.
    l. Connect the Motor Cable Plug that was previously connected to the Foot Pedal to the CoPilot receiver Power Connection that has the female receptacles.
    m. The Foot Pedal Connection from the CoPilot receiver can be connected to the Foot Pedal once the installation is complete.
    n. Place the Power Cable and the Foot Pedal Connection from the CoPilot Receiver on the Base Extrusion so that it can be captured in the Strain Relief Bracket.

  7. o. Using a #3 Screwdriver, replace the screw that was holding the Strain Relief Bracket in place.
    p. Be sure that the wires are routed in a way that they can not be pinched and reseat the Center Housing in place.
    NOTICE: The wires should pass under the Center Housing over the Base Extrusion in the notch that creates a separation from the base and the housing. The connection between the Motor Cable Plug and the Power Connection should be under the Center Housing when it is seated.

  8. q. Once the wires are in place and the Center Housing is seated, stow the motor to replace the Left Sideplate
    r. Replace the Right Sideplate.
    MINN KOTA 1358763 CoPilot for Freshwater Trolling Motor -
ReplaceMINN KOTA 1358763
CoPilot for Freshwater Trolling Motor - Left Sideplate

  9. s. Using a #2 Phillips Screwdriver, replace the four 1/4-20 x 5/8’’ Screws from the Right Sideplate and Left Sideplate of the PowerDrive mount.
    MINN KOTA 1358763 CoPilot for Freshwater Trolling Motor -
Screwdriver

COPILOT

CONTROLLING THE MOTOR WITH A COPILOT
Review the complete CoPilot section of this manual to become familiar with this feature. For more information on CoPilot or for additional product support, please visit minnkotamotors.com.

Prop ON/OFF
This button is located in the middle of the remote. It turns the propeller on or off. Press the button once to turn the propeller ON; press the button a second time to turn it OFF. The button does not need to be held down.

Steer Left & Steer Right
These buttons are located to the right and left of the Prop ON/OFF button and have an arrow symbol. They cause the motor to turn in the desired direction as long as the button is held down. If the Steer Right or Steer Left button is held for more than seven seconds, the steering will automatically stop until the button is pressed again.

Increase Speed & Decrease Speed
The Increase Speed and Decrease Speed buttons are located on the top of the remote and are identified with a positive and negative symbol. Pressing and releasing these buttons causes the speed to increase or decrease by increments of 1. The speed is adjustable from level 0-to 10. At level 0, the prop will not turn.
In audio mode 2, an audible beep is heard for each increment when changing speed. Attempting to go higher than speed 10 or lower than speed 0 will result in the speed not changing and no beep will be heard. See the Audio Mode section for more information.
If the receiver senses no foot pedal or remote operation for 1 hour, the remote speed setting is automatically set to zero. This helps prevent unintentional activation of the propeller if the prop on/off remote button is inadvertently pressed.

COPILOT GENERAL OPERATION
Operating with the Remote and Foot Pedal

  • When the Momentary/Constant Switch on the Foot Pedal is in the CON position or when the Momentary Button is held, the receiver WILL NOT RESPOND to any remote commands. When remote commands are received, the receiver will emit an audible chirp. This will indicate that the remote is functioning properly, but the Foot Pedal is active and is overriding the remote.
  • When the Momentary/Constant Switch is in the MOM position, the operator may begin using the remote at any time.
  • As soon as any remote button is pressed, the initial speed setting will be set to approximately the same value as the Speed Control value on the Foot Pedal. The prop will not automatically turn on until the Prop ON/OFF button on the remote is pressed.
  • Pressing the Momentary Button on the Foot Pedal or adjusting the Speed Control dial will override the remote and receiver function. Control of the motor will automatically go to the Foot Pedal. The prop speed will also revert to the current value of the Speed Control dial on the Foot Pedal.

Operating without the Foot Pedal
• If the foot pedal is not being used, the CoPilot receiver will always react to any commands from the CoPilot remote.

AUDIO MODES
There are three receiver Audio Modes available. The unit is factory set to Audio Mode 2. To switch from one audio mode to another, simultaneously press and hold the increase and decrease speed buttons for one second. The receiver will respond with 1, 2, or 3 audible beeps indicating the corresponding receiver audio mode change.

Audio Mode Function
Mode 1 All of the normal audible sounds are mentioned in this owner’s manual,

but no audible beeps for speed increase/ decrease or prop on/off.
Mode 2| Same as audio mode 1 plus an audible beep for speed increase/decrease and prop on/off.
Mode 3| Same as audio mode 2 plus the prop on audible tick every 1.5 seconds.

NOTICE: When the Foot Pedal (if applicable) is operating the motor and the propeller is on, the prop on indicator tick will be heard if the receiver is set to Audio Mode 3.

Audio Pattern

| What Condition Causes Audio Pattern|

Audio Mode

---|---|---
1 Beep| Pressing the Increase Speed or Decrease Speed button| Modes 2 and 3
1 Beep| Pressing the Prop ON/OFF button to turn the Prop on| Modes 2 and 3
2 Beeps| Pressing the Prop OWOFF button to turn the Prop off| Modes 2 and 3
Single tick every 1.5 seconds| When the Prop is active including when the Speed Control dial is set to 0| Mode 3
1 Beep| Switching to audio Mode 1| All
2 Beeps| Switching to audio Mode 2| All
3 Beeps| Switching to audio Mode 3| All
1 Chirp| Every time the receiver is powered up and there is at least one remote learned| All
2-second long Beep| Every time the receiver is powered up and there are no remotes learned| All
5 Beeps| The speed Control dial on Foot Pedal (if applicable) is moved after the speed has been adjusted with remote| All
Steady Tone| Heard while holding down the Learn button on the receiver| All
4 Beeps| Heard after a remote button is pressed while the receiver learns it.| All
Ten-second warbling sound that transitions into a steady tone| Heard during the process used to clear all stored remotes. after the learn switch is released, a 2-second long beep will be heard| All
1 long beep, 2 short Beeps, pause (repeat)| Powered up with Momentary/Constant Switch in the CON position (or the Momentary Button held) when the Foot Pedal (if applicable) is moved to momentary, the power-up audio will be heard| All

ADDING/REMOVING REMOTES
The CoPilot remote came from the factory already “Learned” by the CoPilot receiver. Any additional remotes must be “Learned” by the receiver. The receiver stores all “Learned” information even when the motor is disconnected from a power source.

To “Learn” Remotes
Your receiver may learn up to ten remotes. Any additional remotes can be “Learned” using the following steps. This will also work to “Learn” any remote if all remotes are erased from the receiver.

  1. a. Using a small blunt object such as a pen or screwdriver, press and hold the Learn Button located on the side of the receiver.
    b. The receiver will emit a continuous tone.
    MINN KOTA 1358763 CoPilot for Freshwater Trolling Motor -
Remotes

  2. c. Press any button on the remote.
    d. The receiver will beep 4 times confirming that it has “Learned” the remote successfully.
    MINN KOTA 1358763 CoPilot for Freshwater Trolling Motor - Remotes
2 NOTICE: “Learning” the same remote will not overwrite previously “Learned” remotes. If the receiver has “Learned” ten remotes, “Learning” an eleventh remote will overwrite the first remote.

To Erase All Remotes from the Receiver

  1. a. Remove power from the CoPilot receiver by disconnecting the Power Cables, or by making sure that the breaker, if equipped, is “off”.
    MINN KOTA 1358763 CoPilot for Freshwater Trolling Motor - CoPilot
Receiver

  2. b. Press and hold the Learn Button and power up the CoPilot receiver by reconnecting the Power Cables, or by making sure that the breaker, if equipped, is “on.”
    c. Continue to hold the Learn Button down for 10 seconds. During this time the receiver audio will emit a warble sound, slowly transition to a constant beep and then shut off.
    d. Release the Learn Button and the receiver will reboot. The receiver will emit a 2-second long beep indicating memory is empty. This audio pattern will occur each time the receiver powers up until a remote ID number is “Learned.”
    MINN KOTA 1358763 CoPilot for Freshwater Trolling Motor -
Button

REPLACING THE BATTERY

  1. a. Temporarily ground yourself by touching a grounded metal object in order to discharge any static electricity in your body.
    NOTICE: The replacement battery must be a model CR2032 coin cell type. It is strongly recommended that a name-brand battery is used.
    b. Remove the four screws on the bottom of the remote case.
    c. Separate the case halves to access the circuit board.
    MINN KOTA 1358763 CoPilot for Freshwater Trolling Motor - REPLACING THE
BATTERY

  2. d. To remove the Battery, place the tip of a finger or thumb under the exposed edge of the Battery and pry it upwards.
    e. Install the new battery with the positive (+) side of the Battery facing up and away from the Circuit Board. Ensure Battery is snapped securely in place.
    NOTICE: The replacement battery must be a model CR2032 coin cell type. It is strongly recommended that a name-brand battery is used.
    MINN KOTA 1358763 CoPilot for Freshwater Trolling Motor - REPLACING THE
BATTERY 2

  3. f. Reassemble the remote. Begin by removing the board from the front of the remote case. This is the same board that holds the battery. Leave the Keypad in place on the front of the remote.
    g. Note that the alignment peg in the back of the remote case must line up with the corresponding alignment hole in the circuit board. Place the board with the battery facing down on the back of the remote case.

  4. h. Position the back of the remote case so that the Alignment peg is towards the top when the remote is laying on a flat surface. Position the front of the remote case so the keypad and the curved buttons are towards the bottom when the remote is laying on a flat surface.
    i. Keep the back of the Remote Case flat. Place the front of the Remote Case, with the Keypad, is a place, on the back of the Remote Case. Make sure the Case is seated.
    MINN KOTA 1358763 CoPilot for Freshwater Trolling Motor -
Circuit

  5. j. Reinstall the four case screws and tighten them as required.MINN KOTA 1358763 CoPilot for Freshwater Trolling Motor - screws and tighten

COMPLIANCE STATEMENTS

ENVIRONMENTAL COMPLIANCE STATEMENT
It is the intention of JOME to be a responsible corporate citizen, operating in compliance with known and applicable environmental regulations, and a good neighbor in the communities where we make or sell our products.

WEEE DIRECTIVE
EU Directive 2002/96/EC “Waste of Electrical and Electronic Equipment Directive (WEEE)” impacts most distributors, sellers, and manufacturers of consumer electronics in the European Union. The WEEE Directive requires the producer of consumer electronics to take responsibility for the management of waste from their products to achieve environmentally responsible disposal during the product life cycle.

WEEE compliance may not be required in your location for electrical & electronic equipment (EEE), nor may it be required for EEE designed and intended as a fixed or temporary installation in transportation vehicles such as automobiles, aircraft, and boats. In some European Union member states, these vehicles are considered outside of the scope of the Directive, and EEE for those applications cabe considered excluded from the WEEE Directive requirement.

This symbol (WEEE wheelie bin) on a product indicates the product must not be disposed of with other household refuse. It must be disposed of and collected for recycling and recovery of waste EEE. Johnson Outdoors Inc. will mark all EEE products in accordance with the WEEE Directive. It is our goal to comply with the collection, treatment,  recovery, and environmentally sound disposal of those products; however, these requirements do vary within European Union member states. For more information about where you should dispose of your waste equipment for recycling and recovery and/or your European Union member state requirements, please contact your dealer or distributor from which your product was purchased.

DISPOSAL
Minn Kota motors are not subject to the disposal regulations EAG-VO (electric devices directive) that implements the WEEE directive.
Nevertheless never dispose of your Minn Kota motor in a garbage bin but at the proper place of collection of your local town council.
Never dispose of battery in a garbage bin. Comply with the disposal directions of the manufacturer or his representative and dispose of them at the proper place of collection of your local town council.

REGULATORY COMPLIANCE INFORMATION
MODEL: COPILOT

  • IC: 4397A-M05COPLT
  • FCC ID: MO5COPLT

COMPLIANCE STATEMENTS

FCC COMPLIANCE

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference.
  2. This device must accept any interference that may be received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by Johnson Outdoors Marine Electronics, Inc. could void the user’s authority to operate this equipment.

NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

INDUSTRY CANADA COMPLIANCE
This product meets the applicable Industry Canada technical specifications. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Changes or modifications not expressly approved by Johnson Outdoors Marine Electronics, Inc. could void the user’s authority to operate this equipment.

ENVIRONMENTAL RATINGS
Ambient operating temperature range: -10C to 50C
Ambient operating humidity range: 5% to 95%
Maximum operating altitude: 10,000 feet

RADIO OPERATION

  • Frequency band: 433.92 MHz
  • Maximum RF power transmitted: +7 dBm

CE MASTER USER MANUAL (FORCE CERTIFIED MODELS)

SERVICE & MAINTENANCE

TROUBLESHOOTING THE COPILOT

Cause
The Remote is not transmitting.|

Effect
The battery is discharged.

| Solution
Replace battery.
---|---|---
The receiver may not have ‘learned” the remote.| Remote needs to be learned. See the Adding/Removing Remotes section of this manual to learn the remote.
With the. foot. pedal (if applicable) connected, the MOM-. CON switch is in the CON position. An audio response will be heard if a button is pressed with the foot pedal in the CON position.| The foot pedal (if applicable) switch must be placed in  Momentary Mode (MOM). The receiver will not accept any commands from the remote with the switch in the Constant Mode (CON) position.
If the remote has been taken apart, the keypad and top case may have been installed backward.| Take the remote apart. See the Replacing the Battery section of this manual and reinstall case halves with the proper orientation.
When the receiver is powered up, it sounds like a beep pattern (1 long beep, 2 short beeps. pause, repeat).| The foot pedal (if applicable) Momentary/Constant Switch is in the CON position.| The. foot pedal (if applicable) switch m. must be .placed in the. MOM. position. The beeping sound will continue until the switch is placed in the MOM position.
The prop is not turning but the Prop ON audio pattern is still going.| Prop Speed is set at “0”.| Increase the Prop Speed above “0”
The Prop ON audio pattern occurs only in Audio Mode 3|

Switch Audio Mode to either Audio 1 or 2. See the Audio Modes section of this manual.

FOR FURTHER TROUBLESHOOTING AND REPAIR
We offer several options to help you troubleshoot and/or repair your product. Please read through the options listed below.

Buy Parts Online
You can buy parts online directly from our website at minnkotamotors.com. Orders confirmed by 12-noon central time will ship the same day if in stock. Orders after 12-noon central time will ship the next business day if in stock.

Frequently Asked Questions
We have FAQs available on our website to help answer all of your Minn Kota questions. Visit minnkotamotors.com and click on “Frequently Asked Questions” to find an answer to your question.

Call Us (for U.S. and Canada)
Our consumer service representatives are available Monday – Friday between 7:00 a.m. – 4:30 p.m. CST at 800-227-6433. If you are calling to order parts, please have the 11-character serial number from your product, specific part numbers, and credit card information available. This will help expedite your call and allow us to provide you with the best consumer service possible. You can reference the parts list located in your manual to identify the specific part numbers.

Email Us
You can email our consumer service department with questions regarding your Minn Kota products.
To email, your question, visit minnkotamotors.com and click on “Support”.

Authorized Service Centers
Minn Kota has over 800 authorized service centers in the United States and Canada where you can purchase parts or get your products repaired. Please visit our Authorized Service Center page on our website to locate a service center in your area.

Scan to visit Minn Kota service online.http://DELIVR.COM/2A49AQR

PARTS DIAGRAM & PARTS LIST

COPILOT ACCESSORY
POWERDRIVE
CoPilot Parts Diagram
MINN KOTA 1358763 CoPilot for Freshwater Trolling Motor -
Diagram

CoPilot Parts List

Assembly
A

| Part #
2994112| Description
CTRL BOARD V2 COPILOT Receiver|

Quantity
1

---|---|---|---
B Item
2| 2994020 Part # 2373418| TRANSMITTER. ASY. PD/AP COPLT Description
SCREW-#8 X 5/8 PPHSMS S/S| 1
Quantity
4| 2374092| CTRL BOARD V2 COPILOT RECEIVER|
6| 2372503| CASE. COVER, TRANSMITTER ASY| 1
8| 2375110| KEYPAD, TRANSMITTER ASSY| 1
10| 2372505| CASE. BOTTOM. TRANSMITTER ASSY| 1
12| 2373440| SCREW-#4-24 X 1/4 PHCR SS TY B| 4
14| X| PCB ASV, CO-PILOT TRANSMITTER| 1
16| 2390801| LANYARD, REMOTE| 1
•| 2005621| DECAL – CURCM/WEE CMPLNC.MARK| 1
A| 2317166| MANUAL-CO-PILOT V3| 1

✖ This part is included in an assembly and cannot be ordered individually.
Not shown on Parts Diagram.

RECOMMENDED ACCESSORIES

ON-BOARD & PORTABLE BATTERY CHARGERS
Stop buying new batteries and start taking care of the ones you’ve got. Many chargers can actually damage your battery over time – creating shorter run times and shorter overall life. Digitally controlled Minn Kota chargers are designed to provide the fastest charge that protects and extends battery life.

TALON SHALLOW WATER ANCHOR
Introducing the all-new, sleek redesigned Talon. Talon is the only shallow water anchor with up to 15’ of anchoring depth, multiple anchoring modes, and control from the bow, transom, console, remote or mobile device.

BUILT-IN WORK LIGHT
Let’s you tie lines and work from the transom any time of day — or night. Includes both white and blue LED lights with three brightness settings.

MINN KOTA 1358763 CoPilot for Freshwater Trolling Motor -
BLUETOOTH® BLUETOOTH® CONNECTIVITY
Let’s you control Talon from your mobile device and easily update it. Also opens up communication to other control options.

UP TO 15’ DEEP
Control more water and catch more fish with the first 15’ shallow water anchor.

MORE CONTROL OPTIONS

  • Control Panel
  • Wireless Remote
  • Mobile App
  • Wireless Foot Switch
  • Humminbird® Connectivity
  • i-Pilot® & i-Pilot Link TM Remote

MINN KOTA ACCESSORIES
We offer a wide variety of trolling motor accessories, including:

  • 60-Amp Circuit Breaker
  • Mounting Brackets
  • Stabilizer Kits
  • Extension Handles
  • Battery Connectors
  • Battery Boxes
  • Quick Connect Plugs

MINN KOTA - logominnkotamotors.com
Part #2377166

Minn Kota Consumer & Technical Service Johnson Outdoors Marine Electronics, Inc.
PO Box 8129
Mankato, MN 56001
ECN 40105
121 Power Drive
Mankato, MN 56001
Phone 800-227-6433
Fax 800-527-4464

©2019 Johnson Outdoors Marine Electronics, Inc.
All rights reserved.
Rev D
09/19

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

MINN KOTA User Manuals

Related Manuals